Broadata USW-88 Manuale utente
USW-88
UNIVERSAL 8X8MATRIX SWITCH
BCI reserves the right to make changes to the products described herein without
prior notice or consent. No liability is assumed as a result of their use or
application. All rights reserved.
©2008 Broadata Communications, Inc.
BCIUSW-88 User’s Manual
Universal 8x8 Matrix Switch
SAFETY INSTRUCTIONS AND
COMPLIANCE DECLARATIONS
PLEASEOBSERVETHEFOLLOWINGSAFETY
PRECAUTIONSASOURPRODUCTS CONTAIN
CLASS I LASER PRODUCTS
WARNING
Do not disconnect the fiber optic connector while the unit is powered
up. Exposure to laser radiation is possible when the laser fiber optic
connector is disconnected while the unit is powered up.
Although the fiber optic connectors in this product emit only Class 1
energythatisbelowthelevelsconsidered to be hazardous, one should
neverstaredirectlyintoafiberopticconnectororanunconnectedfiber
end unless one can be certain that no exposure to laser energy could
occur.
CAUTION
This manual is intended for use by trained service personnel. The use
of controls, making adjustments, or performing operations other than
those specified may result in hazardous radiation exposure.
Thefollowinglabelorequivalentislocatedonthesurfaceoflaserproducts.
Thislabelindicatesthat the product is classified as a CLASS 1 LASER
PRODUCT.
SURGEPROTECTION DEVICERECOMMENDED
This product contains sensitive electrical components that may be
damaged by electrical spikes, surges, electric shock, lightning strikes,
etc. Use of surge protection systems is highly recommended in order
to protect and extend the life of your equipment.
BCIUSW-88 User’s Manual
Universal 8x8 Matrix Switch
Broadata Technical Support, (800) 214-0222
4
TABLE OF CONTENTS
1.0 PRODUCT DESCRIPTION .............................................5
2.0 OPERATION CONTROLS AND FUNCTIONS ...............6
3.0 REMOTE CONTROL ......................................................9
3.1 IR CUSTOM CODE ......................................................10
3.2 DISCRETE IR CODES .................................................10
3.3 IR RECEIVER ...............................................................11
4.0 RS-232 PROTOCOL.....................................................12
4.1 PIN ASSIGNMENT........................................................12
4.2 COMMANDS .................................................................13
5.0 VIDEO CONNECTION DIAGRAM.................................16
6.0 RACK INSTALLATION ...................................................17
7.0 SPECIFICATIONS..........................................................18
8.0 SERVICE PROCEDURE ...............................................20
8.1 REPLACEMENT POLICY .............................................20
8.2 RETURN AND REPAIR SERVICE .................................20
9.0 LIMITED WARRANTY ....................................................21
BCIUSW-88 User’s Manual
Universal 8x8 Matrix Switch
1.0 PRODUCT DESCRIPTION
The USW-88 Series is a high performance Universal Matrix Switcher
Systemthatprovides8x8videoswitchingfor HDMI/DVIsignals.Standard
versions of the USW-88 support all optical switching, or hybrid
optical/electrical switching for HDMI/DVI signals. When configured for
opticalswitching,only onemultimodefiberis requiredperinputor output
port.Inaddition, thedistancebetweenthe switchandHDMI/DVIdevices
can be up to 400m when connected by fiber cable.
TheUSW-88isatrueHDMI1.3switch,supportingjitter-free,high-quality
HDMI/DVIDisplaywith10-bitdeepcolordigitalvideoformatand Dolby
orDTS featureddigital audioformat.Itcomeswiththreetypesofswitching
control:manualcontrolpanel,PCbasedcontrolsoftwarethroughstandard
RS-232/422,orremoteIRcontrol.
The USW-88 comes in a 3-RU packaging design.
TheUSW-88hasthefollowingconfigurations:
USW-88DVI 8x8 Universal Switch, DVI
USW-88HDMI 8x8 Universal Switch, HDMI
USW-88FOP 8x8 Universal Switch, Optical
USW-44D44F 8x8 Universal Switch, 4-DVI, 4-Optical
USW-88HDMI 8x8 Universal Switch, 4-HDMI, 4-Optical
8x8
DVI DV
I
88
8x8
HDMI HDMI
88
8x8
Optical
Optical 88
8x8
Optical
DVI
Optical
DVI
44
44
8x8
Optical
HDMI
Optical
HDMI
44
44
Model Description I/O Configuration
BCIUSW-88 User’s Manual
Universal 8x8 Matrix Switch
Broadata Technical Support, (800) 214-0222
6
2.0 OPERATION CONTROLS AND FUNCTIONS
FrontPanel
1. Display monitor: This monitor displays switch settings
informationwith each output and input selection.
2. IRsensor:ForremoteIRcontrol.
3. POWER: Press this button to turn the system on. Once the
system turns on the LED will turn Green and when entering
Standby Mode it will turn Red.
4. EDID:Therewillbetwoselectionsshownonthe DisplayMonitor:
1. TV mode and 2.Standard Mode, press the number key to
firstselectthedesiredinput and thenpressoneortwoto select
the EDID mode. The LED will turn on when setting the EDID.
After the selection is made, press CONFIRM key to confirm.
TV Mode meansthedevice willusedisplay’sEDID. Thefactory
default setting is TV mode. When EDID is switched to a TV
Mode, the USW-88 will first detect the output source’s EDID
fromA-D and then record it in the USW-88 unit, regardless of
theoutputsourcesfromE-H.Ifthefirstdetected output source
is DVI it will pass on to the next source, until the first HDMI is
detected. The detection priority is HDMI v1.3 > HDMI v1.2 >
DVI.Inorderto ensure alloutputisdisplayable output from E-H
must be of a lower standard than output fromA-D.
LOCK
GHF
786
DEC
453
RECORD RESTORE
ALL OUTCONFIRM
AB
OUT
12
EDID
POWER
USW - 88
UNIVERSAL 8 x 8 SWITCH
DISPLAY MONITOR
IN
FUNCTIONS
12345678910
BCIUSW-88 User’s Manual
Universal 8x8 Matrix Switch
StandardModemeansthedevicewilluseinternalbuilt-inEDID.
When EDID is on Standard Mode, the USW-88 will use the
built-in EDID. In this case, Video Supports is less than 1080p,
10 bits (max), andAudio Supports is PCM2.
5. LOCK: Press this button to lock all the functions and press it
again to release the lock. When LED turns green, the lock is
activatedandwhenit turns red thekeylockhasbeen released.
6. CONFIRM:Pressthisbuttonaftereachandeveryselectionto
confirm the setting. If this button is not pressed after 20
seconds, the selection will be cancelled.
7. ALL OUT: Press this button to set all the outputs to display
with the same input.After pressing theALLOUT button, press
an input number and then press CONFIRM to confirm the
selection.
8. RECORD:Pressthis button tochooseyoursix pre-setsettings.
First press the setting number, and when all the input/outputs
are being set, be sure to press RECORD to record it into the
system. The factory default settings are 1.12345678,
2.87654321,3.11223344,4.55667788,5.11221122,6.33443344.
9. RESTORE:Selectthis buttoninorderto restoreyoursixpre-set
settings, then press CONFIRM key to confirm your selection.
10. OUTA~H & IN 1~8: Press the output source selection button
inorder to choose which input port corresponds to the desired
output port. First select your output port from A-H, wait 2
seconds, then choose the desired input port from ports 1-8,
pressing CONFIRM key will confirm your setting. Each output
selection only allows a single input setting each time.
BCIUSW-88 User’s Manual
Universal 8x8 Matrix Switch
Broadata Technical Support, (800) 214-0222
8
IR RX
RS-232 USB
POWER
(PROGRAM)(UPGRADE)
RS-232
(CONTROL)
HG
OUTPUTS F E
ABCD
INPUTS
7 68
234 1
5
FAN
PWR
LINK
PWR
LINK
PWR
LINK
PWR
LINK
PWR
LINK
PWR
LINK
PWR
LINK
PWR
LINK
PWR
LINK
PWR
LINK
PWR
LINK
PWR
LINK
PWR
LINK
PWR
LINK
PWR
LINK
PWR
LINK
1234567
8
POWER 100-240VAC
RearPanel
1. OUTPUT A~H: These slots are where you connect the video
displaythrough HDMI, DVI or Optical connections.
2. RS-232(UPGRADE):Thisslotis where youconnectaD-sub9
malepinconnectorcableto your host, in ordertoupgradeyour
firmware.
3. RS-232(CONTROL):Thisslotis where you connect aD-sub9
female pin connector cable to your host so you can control
USW-88 switch settings.
4. USB(PROGRAM):This slotiswhereyouconnect aUSBb-type
connector cable to your host for System Program firmware
downloading.
5. IR RX: This slot is where you can extend your IR receiver with
an IR extender cable that accepts only 38KHz.
6. INPUT 1~8: These slots are where you connect the video
sourcesthrough HDMI, DVI or Optical connections.
7. POWER: This LED will turn GREEN when power is on.
8. Power 95-240 VAC: This is theAC power entry and switch.
BCIUSW-88 User’s Manual
Universal 8x8 Matrix Switch
3.0 REMOTE CONTROL
Section 3.1 shows the IR code for the remote control. There are a total
of four dipswitches located at the rear bottom of the remote control.
WhendipswitchesareallsettoON(upperposition), the remote control
isabletocontrolallthe outputsandinputs.For example, when outputA
wishes to select input 5, first press 1, wait a second, then press 5, and
instantly output displayA will show input source 5’s image.
Forothersettingspleaserefer to Section 3.2.Forexample,whenall the
dipswitches are set to OFF, this setting is for output A, so it can only
controlinputselections. WhenoutputAwishestoselectinput 3,pressing
3 will allow output displayAto only show input source 3’s content. For
additional settings please refer to Section 3.2.
BCIUSW-88 User’s Manual
Universal 8x8 Matrix Switch
Broadata Technical Support, (800) 214-0222
10
3.1 IR Custom Code
3.2 Discrete IR Codes
OutputA 0cx88 0x89 0x8A 0x8C 0x8D 0x8E 0x90 0x91
Output B 0cx88 0x89 0x8A 0x8C 0x8D 0x8E 0x90 0x91
Output C 0cx88 0x89 0x8A 0x8C 0x8D 0x8E 0x90 0x91
Output D 0cx88 0x89 0x8A 0x8C 0x8D 0x8E 0x90 0x91
Output E 0cx88 0x89 0x8A 0x8C 0x8D 0x8E 0x90 0x91
Output F 0cx88 0x89 0x8A 0x8C 0x8D 0x8E 0x90 0x91
Output G 0cx88 0x89 0x8A 0x8C 0x8D 0x8E 0x90 0x91
Output H 0cx88 0x89 0x8A 0x8C 0x8D 0x8E 0x90 0x91
Select /
Dipswitch Input
1Input
2Input
3Input
4Input
5Input
6Input
7Input
8
No. DATA
188
289
38A
48C
58D
68E
790
891
992
095
BCIUSW-88 User’s Manual
Universal 8x8 Matrix Switch
3.3 IR Receiver
TheUSW-88also comeswitha IRextensionreceiver(seefigurebelow).
Use this receiver, one can remote control the USW-88 at a designated
fieldofview.
Indice
Altri manuali Broadata Commutatore a matrice
