Bticino Sfera Keypad Module Guida utente
353000
Sfera Keypad Module
Installer manual
04/16-01 PC
2
Sfera Keypad Module
Installer manual
3
Contents
1 Introduction 4
1.1 Warnings and recommendations 4
2 Description 5
2.1 Main functions 5
2.2 Front view 6
2.3 Back view 7
3 Configuration 8
3.1 Master code 8
3.1.1 New master code 8
3.1.2 Deleting master codes 10
3.2 Passepartout code 11
3.2.1 New passepartout code 11
3.2.2 Deleting passepartout codes 13
3.2.3 Replacing the passepartout code 14
3.3 Resident code 16
3.3.1 New resident code 16
3.3.2 Deleting the resident code 19
3.3.3 Replacing the resident code 20
4 Advanced configuration 22
4.1 Connection to the PC 22
4.2 Door lock control 23
4.2.1 Door lock control with stand-alone Keypad module 353000 23
4.2.2 Door lock control with Sfera Speaker Module 351100/351200/351300
and Keypad module 353000 23
4.3 Reset 24
5 Appendix 25
5.1 Technical data 25
4
1 Introduction
1.1 Warnings and recommendations
Before proceeding with the installation we recommend that you read the content of this manual
very carefully.
The warranty will automatically become void in case of negligence, improper use, and tampering
by unauthorised personnel.
The Sfera Keypad Module must only be used with BTicino 2 wire digital systems.
Front covers that may be used with the Sfera BTicino Keypad Module:
Front cover 353005 Front cover 353001/02/03
Sfera Keypad Module
Installer manual
5
2 Description
2.1 Main functions
The BTicino Sfera Keypad Module can be used by residents to open a door lock using previously
stored numerical codes.
The device consists of a backlit pushbutton panel with 12 keys and luminous indicators, for con-
trolling that the code has been entered correctly.
Programming can be performed in two ways:
- using the TiSferaDesign software supplied with the product (chapter 4);
- following specific procedures, performed directly on the keypad (chapter 3).
In order to configure the master codes remove the front cover and press the programming push-
button indicated in the legend (chapter 2.2).
The secret code must consist of minimum 4 and maximum 9 digits.
Three different types of codes may be programmed:
- MASTER Code providing access to the programming of other codes.
It can only be used for programming, not for access..
- PASSEPARTOUT It can be used to open the door lock the entrance panel is associated to.
It’s not linked with any apartments.
It can only be used for access, not for programming.
- RESIDENT It can be used to open the door lock the entrance panel is associated to.
It’s linked to an apartment of the system.
It can only be used for access, not for programming.
This manual refers to the Sfera wired stand-alone Keypad Module or paired with the
Sfera Speaker Module (351100/351200/351300).
If the Sfera Keypad Module is installed linked to the Display Module (352500) refer to
the Display manual for the code programming.
6
2 Description
2.2 Front view
1 - Digital keypad + key illumination LED.
key for the selection of the door lock release code.
key for the replacement of the codes.
2 - Mini-USB programming connector.
3 - Programming pushbutton.
4 - Red LED on steady: access denied, or programming error.
5 - Green LED on steady: access granted, or programming successful.
3
2
5
4
1
Sfera Keypad Module
Installer manual
7
2.3 Back view
1 - Connection of door lock pushbutton (CP-P1) and tamper (CP-P2 – future application).
2 - Local relay contacts.
3 - Connection to the BUS.
4 - Connector for the connection to subsequent modules.
5 - Connector for the connection to previous modules.
6 - Configurator sockets.
3 2 1
5
4
6
8
3 Configuration
3.1 Master code
(only with Sfera Speaker Module 351100/351200/351300 and the associated Sfera Pushbutton
Modules 352000/352100 or only with the Sfera Keypad Module)
For safety reasons, the system gives the installer the possibility of programming a“MASTER” code.
This can be used to access the programming of the other codes (passepartout and resident codes).
To access programming mode, a master code must be assigned to the device.; up to 20 master
codes may be saved.
The keypad module will indicate that the code has been accepted or deleted by means of audible
signals and the switching on of the green LED. If an unrecognised code is entered, programming
will stop. This interruption is confirmed by a long beep, and the red LED coming on.
3.1.1 New master code
1 Press the programming pushbutton until the green
LED flashes and a confirmation beep is heard.
2 Press the key. 4 Press the key.
A short beep confirms the
programming of the new
master code
3 Enter the code (4
to 9 digits).
Sfera Keypad Module
Installer manual
9
If the procedure has been successful, the
green LED stays on for approximately 1 second
before starting to flash again.
Enter another code, or finish.
6 Press the programming pushbutton, or wait 30
seconds to exit the procedure.
A short beep and the LEDs switching off indicate that the programming procedure has been
terminated. The Sfera Keypad Module is now ready for normal operation.
During programming, some rules must be followed:
- keys must be pressed consecutively (maximum 2 seconds between pressures);
- the programming sequence must be started within 30 seconds from the moment the
programming pushbutton has been pressed and must be completed in one stage.
5 Re-enter the code to confirm.
Wrong code:
red LED on and long beep
NO
Correct code:
green LED on and short beep.
OK
10
3 Configuration
3.1.2 Deleting master codes
1 Press and hold down the programming pushbutton;
the green LED flashes.
- The procedure will delete all the stored Master codes.
- During the procedure press the programming pushbutton.
- To stop the deletion procedure release the programming pushbutton.
- To only delete a specific code use the TiSferaDesign software.
2 Continue holding down the pushbutton;
the device emits 1 beep per second, and a long beep
after ten seconds
3The red LED flashes and then switches off to confirm
that the deletion has been performed.
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Bticino Tastiera
