BURG WATCHER Door eGuard DG 8200 Manuale utente

BURG-WÄCHTER KG

Altenhofer Weg 15

58300 Wetter

GermanyDoor eGuard DG 8200 06/2017

www.burg.biz

<1sec.

4,0“ TFT

105°

14–26 mm

38–110 mm

AAA

25+2000

OUTDOOR

INDOOR

Door eGuard DG 8200

Operating Instructions

Door eGuard

English |2

Structure

Figure

Digital spyhole

Charge indicator lamp

1 attachment screw

4 x AAA batteries

Holding plate

Camera

Fastening sleeve

Tightening tool

technical function and usage without prior notice to users.

· Use of this product other than that for which it is intended for or

any modiﬁcation to the original speciﬁcation will invalidate any

guarantee given.

· Use of this product in any environment or in any way other than

speciﬁed here will also invalidate the guarantee.

Attention

1. Please read this user manual carefully before using our product.

2. Never attempt to repair or modify this product or its accessories by

yourself, to avoid injury and invalidating guarantee!

3. Any accidental factor such as being struck by lightning or any incorrect

operation could cause

a memory loss on the micro sd-card.

Keeping copies of the pictures is strongly recommended in case of

memory loss. We are not responsible for any loss of data.

4. DO NOT use any chemicals to clean this product, such as alcohol or

benzene thinner.

5. Please change the batteries soon after the low-battery indicator shows,

in order to avoid any damage to this product which could be caused by

battery weeping.

Dear customer,

thank you very much for deciding for Door eGuard manufactured by

BURG-WÄCHTER. Door eGuard is a battery-operated system with a camera

and colour monitor, easy to install and providing its user with the certainty

of being able to see anything happening outside the entrance door without

being seen. Thanks to its large adjustment range, this door spyhole can

be used with any common door with a thickness from 38 to 110mm. The

camera optics can cover existing holes in the door of 14– 26mm. Thanks to

the camera optics with a large viewing angle, even persons hidden near the

door can be identiﬁed.

Important: Please read the entire User Manual before you start to

mount the device.

Let us wish you a high level of security and

quality of living with your electronic spyhole.

Your BURG-WÄCHTER KG

Installation instructions

1. Fixing the camera on the outside of the door.

Replace the existing door position or drill a

14mm hole at the desired position. Peel off the 3M protective ﬁlm and

then guide the camera into the hole from the outside. Take care that the

cable is guided through the door without kinks. Make sure that the bell

push button is located under the camera and align the camera vertical to

the ﬂoor before ﬁxing the camera to the door.

2. Attaching the monitor holder.

Release the monitor holding plate from the rear of the monitor by

unscrewing the screw on the bottom of the monitor using a screwdriver.

Peel off the 3M protective ﬁlm from the rear of the holding plate and

guide the camera cable through the hole in the middle. Make sure that

the arrow on the holding plate points upwards before ﬁxing the holding

plate with the 3M adhesive strip to the inside of the door. Pull the camera

cable through the ﬁxing sleeve and screw this tight using the enclosed

assembly tool.

Door eGuard

English |3

3. SD card

Insert a micro SD card into the card slot in order to be able to save more

than 25 images and export data. To open the SD slot, push the sheet

metal holder towards the bottom of the device. Now the slot can be

folded open. Insert the micro SD card so that the contacts of the slot and

the SD card are on top of each other. Close the sheet metal holder again

and to ﬁx, push this towards the top of the device.

4. Monitor assembly

Insert the plug of the camera cable into the monitor in such a manner that

the cable points towards the SD card slot. Excess cable should be carefully

stowed in the depression on the back side of the screen. Make sure that it

cannot be crushed by the monitor holder.

Push the monitor parallel to the door onto the holder so that the bottom

plate with the screw hole disappears into the intended recess in the

bottom of the screen housing.

By pulling down the monitor slowly, this hangs into the top holder.

Using the screw, ﬁx the device to the door through the hole on the

bottom of the screen housing.

Door

Installation:

Slide the lid upwards to open, as shown in diagram.

Put in the batteries according to the “+” “-” sign on the lid.

Take the reverse steps to close the lid.

Attention:

1. DO NOT force when opening and closing the lid to avoid lid damage.

2. DO NOT press the lid to the opposite direction when opening to avoid any

lid damage.

3. When the low battery indicator is on, please replace all batteries to avoid

any damage to this product by battery weeping.

When the batteries run out, the low battery indicator will ﬂash to remind

users to replace the batteries. The following types of batteries can be used in

this product: AAA, 1.5V alkaline battery. Any abandoned batteries should be

disposed according to local environment protection rules and regulations.

Installation and replacement of batteries

Door eGuard

English |4

Operation instruction

Parts speciﬁcations

Button functions:

No basic function multi functions

Up · In the live view, press UP button to enter picture

browse mode;

· After enters picture browse mode, press UP button

to browse pictures backwards;

· In setting mode, press Up button to adjust the item

you selected;

Menu · Press Menu button to enter menu page;

· When deleting pictures, press Menu button you

can then choose to delete the current photo;

· In picture browse and setting mode, press and

hold the menu button to exit the current page.

Down · In picture browse mode, press Down button to

browse pictures onwards;

· In setting mode, press Down button to adjust the

item you selected;

· In the live view, press Down button to take

picture.

Power Button · After installing new batteries, press and hold

power button to start.

Time setting

Date setting

Ringtone setting

Volume setting 0: silent mode

3: Max volume

Auto power-off setting

Save ﬁle in

· local ﬁle (data can not be downloaded)

· micro sd-card (data can be loaded from the

sd-card via card reader)

To observe outdoors

• Under normal mode, you can observe outdoors

once you press the power button.

• When visitors press the door bell, the bell will ring inside the room.

The screen will automatically turn on showing the image of outside.

It will automatically power off once the set time is reached.

• Under normal mode, press “ ” will take a picture

of outdoors and save it automatically.

Back side of screen case

camera data wire connector

micro sd-card socket

System settings

• Under normal mode, press “ “ to enter setting mode.

• Then you should see the below setting mode page.

• Press “ “ to find different settings:

Time--Date--Ringtone--Volume--

Auto power-off time--Save file in

• Press “ “ to change the settings.

• In TIME/ DATE setting, press “ ” will increase the current number; Holding

the button down will accelerate the adjustment.

• After the setting is changed, the system will automatically save the result

and exit the setting page in a few seconds.

• If you need to exit the setting page, press and

hold “ “.

Door eGuard

English |5

Visitors

• When visitors press the door bell button on the door viewer camera,

the door bell will ring inside the room.

• Meantime, the screen will automatically turn on, showing the image of

outdoors. It will automatically power off once it reaches the set time.

• Also as the door bell is pressed, the camera will automatically take a photo

of the visitors and the photo will be stored in the set file in case the host is

out, so as to check the visitors‘ identity afterwards or

to use the information for security purposes

Replay and delete of the photos

• Under normal mode, press “ ” to replay photos.

• When you browse the photos, press “ ” or “ ” to choose photos.

Current photo number/total number

Month/ date

Shooting time

When you check the photos, press button “ ” to choose to delete the

current photo.

After a short press on the button, you will see below icon:

• Press “ ” to confirm to delete.

Caution

Alterations and modiﬁcations that are not explicitly authorised by the

responsible approval agency, can lead to a deprivation of the permission to

use the device.

Important: Legal note

Acquisition, recording and saving of video surveillance data

(sound and vision) are regulated by strict German guidelines.

Please note the valid provisions regarding data protection laws

that are stipulated in the Federal Data Protection Act resp. Land

Protection Act. For other countries the respective national data

protection laws are valid.

Disposal

Dear customer,

Please help us avoid unnecessary waste. Should you ever intend to dispose of

this device, please bear in mind that many components of the device contain

precious materials, which can be recycled.

Please be aware that electrical and electronic equipment and

batteries shall not be disposed of as household waste, but rather

collected separately. Please obtain information on the collecting

points for electrical waste from the responsible authority of you

municipality.

If you have any questions concerning the EC

declaration of conformity, please use [email protected].

Choose your auto-store ﬁle

• Users can choose to save photos in local file or TF card.

• The default store is local file.

Memory Card Installation

• There is NO micro sd-card included. This should be purchased by

user separately.

• Please insert the micro sd-card before installing batteries.

• Before inserting the micro sd-card, make sure the metal cover above

the micro sd-card socket is pushed towards the OPEN mark.

• Lift and open the upper of the metal cover and insert micro sd-card

into the metal cover.

• Then replace the metal cover and push back to LOCK mark.

• Max. 8GB micro sd-card can be used, over HDSC Class 6 is suggested.

Speciﬁcations

Door thickness 38~110mm

Camera 0.3 Mega pixels

LCD Screen 4.0" TFT

Resolution QVGA (480x 320)

Power 4 AAA,

1.5V alkaline battery

Local memory

storage

Approx 25 photos (The amount could differ depending

on the type of environment the camera is situated in)

Exterior card

type

Micro SD-card (TF), max 8GB

Photo volume

for 1

2,000pc (lab condition, the actual volume could differ

under different circumstances)

Size 139(w) x77 (H)x 15.8(D)mm

Weight 185g

Mistakes and changes reserved.

Altri manuali BURG WATCHER Sistema di interfono

BURG WATCHER

BURG WATCHER TSE 3004 Manuale utente

Manuali Sistema di interfono popolari di altre marche

Bticino

Bticino LINEA 3000 Manuale utente

MSI

MSI MSI-140 Manuale utente

golmar

golmar Stadio Plus Manuale utente

CyberData

CyberData 011211 series Manuale

Vidos

Vidos duo M1021 Manuale utente

Vimar

Vimar ELVOX 7539/E Manuale utente

SSS Siedle

SSS Siedle BTSV 850-03 Manuale utente

Dahua

Dahua VTO Series Manuale utente

Elvox

Elvox 5651 Manuale utente

Videx

Videx VIDEOKIT Series Manuale utente

Rocom

Rocom Doortello Business FW T2.05W2.04 Manuale utente

Viking

Viking E-35-EWP Manuale utente

Safeguard Supply

Safeguard Supply LRA-EX1000 Manuale utente

SSS Siedle

SSS Siedle BFCV 850 Series Manuale utente

GRD

GRD MAX V2 Manuale utente

Alecto

Alecto ADI-250 Manuale utente

Aiphone

Aiphone IE-8MD Manuale utente

Perel

Perel EDB4 Manuale utente