bvk otcaccess C5 Manuale utente
OTCaccess C5 introduction
Dear field operator,
We are introducing you to OTCaccess C5 –new generation, smart lock system, designed to ease
the access process as well as secure valuable assets.
OTCaccess is a unique access management solution developed by BVK Technology. It is
designed to manage multiple scattered access points (places that need to be accessed) with
OTCs (One Time Codes).
An OTC is a One Time Code used by a field operator to unlock a certain location. The OTCs are
generated based on the person who is going to use it (a certain field operator), the lock that needs
to be accessed, the starting time within which the field operator will access and the action to be
taken at the lock (unlock, exit penalty mode, manually synchronize the time of the device, etc.).
Therefore, in case one of this factor is wrong at the moment of entrance, an OTC could be either
generated in advance or requested at the moment of access.
A field operator, the person who will unlock the lock, is defined by a PIN-code. Each PIN-code is
unique and cannot be shared with other field operators. A PIN-code may or may not include autho-
rization level of the field operator depending the corporate policies. Please ask your administration
about your status.
OTCaccess locks are designed to work in offline environments, however, once connected to the
network, all the actions taken regarding the lock will be real-time monitorable by the monitoring
center.
FCC Compliance Information
OTCaccess C5 controller with FCC ID: 2A4FC2105
OTCaccess MiniSmart Bluetooth Keypad with FCC ID: 2A4FC2303
OTCaccess Secure Safe Lock FCC ID: 2A4FC2103
The devices comply with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) the devices
may not cause harmful interference, and (2) the devices must accept any interference received, including interference
that may cause undesired operation.
Note: The equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation.
The equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation.
If the equipment does cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications to this product not authorized by BVK Technology could void the electromagnetic compatibility
(EMC) and wireless compliance and negate your authority to operate the product.
Getting started
Before You Start Using the Device:
- As a field operator, make sure you know your PIN code in advance. If you are using the
system for the first time, make sure you received your PIN code via SMS and/or e-mail. PIN digits
may vary between 4-6 digits based on your corporate preferences. In case you forgot your PIN
code, or haven’t received one, contact your administrator.
- Make sure you have got an 8-digit OTC from your administration via SMS/e-mail/phone
call/custom application.
- Make sure that you know for which door your OTC is generated for.
- In case you have to use OTCaccess mobile app to request the OTC yourself, please check
“OTCaccess Mobile App User Manual”.
- Ask your administration if the device have got a Time Delay or an Opening Window defined.
In case it does, please check “Time Delay” and “Opening Window” sections of this manual.
- Make sure that the OTCaccess device conforms installation standards and that it is in
working state.
1 www.bvktechnology.com
Note: It is preferred for devices to work online in order to make sure that all actions are
monitored real-time by the operation center.
LCKD/ # - the state of the lock. LCKD means that the lock is
locked, number (or rotating numbers) indicates which lock is
unlocked. The number of the lock will be shown instead once
you enter a valid OTC and unlock it.
CLSD/ # - the state of the door. CLSD means that the door is
closed, -- means that the door is open. number (or rotating
numbers) indicates which door is closed/open. The number of
the door will be shown once you open/close it.
PNLT1/PNLT2 - In case many wrong OTC entries were
made, the device gets into 1st Penalty or 2nd Penalty Mode.
To get more information about Penalty mode, check “1st
Penalty Mode” and “2nd Penalty Mode” sections of this
manual.
BLE –whether the Bluetooth of the device is on or off. If your
use case requires to use mobile app over Bluetooth, make
sure the BLE icon is shown on the display.
T –The device is test mode
2 www.bvktechnology.com
OFLN/ONLN –the connection status of the device. OFLN
means that the device is offline, ONLN means that the device
in online. Contact your administrator whether your device
should be online or offline.
whether your device should be online or offline.
Main Screen –The main screen will display the
current state of the device. It will guide you through
OTC validation process.
ARMED –shows that the device is ready to accept
an OTC.
Date –alternatively, “ARMED” will be changed with
the current date
C –The temperature of the environment.
Time –alternatively, the temperature will be
changed with the current time
3 www.bvktechnology.com
1. Enter function code “11”.
Note: Function code number may vary.
Confirm with your administrator.
2. Press green tick button.
3. Enter your PIN code.
Note: In case you forgot your PIN code, or
haven’t received one, contact your administra-
tor.
4. Press green tick button.
5.Enter your OTC.
Note: You should receive your 8-digit OTC
code by SMS/e-mail/phone call. Contact your
administration to get an OTC.
6. Press green tick button.
Unlocking Safe
4 www.bvktechnology.com
1. Enter function code “12”.
Note: Function code number may vary.
Confirm with your administrator.
2. Press green tick button.
3. Enter your PIN code.
Note: In case you forgot your PIN code,
or haven’t received one, contact your
administrator.
4. Press green tick button.
Unlocking Top Box
5 www.bvktechnology.com
In case your code is valid the keypad’s buzzer make 2 short and 1 long beep, the led
on the keypad will turn green and “OTC Valid. Lock01 Unlocked” message will be
displayed. The lock will get unlocked.
Note: There is a 30 seconds timeout for
each entry (function, PIN code, OTC). In
case the entry exceeds 30 seconds, the
OTC validation process will restart.
The cancel button will bring you back to
the first step of your entrance.
7. In case your code is valid the keypad’s buzzer make 2 short and 1 long beep,
the led on the keypad will turn green and “OTC Valid. Lock02 Unlocked” message
will be displayed. The lock will get unlocked.
Note: There is a 30 seconds timeout for each entry (function, PIN code, OTC). In
case the entry exceeds 30 seconds, the OTC validation process will restart.
The cancel button will bring you back to the first step of your entrance.
Close Code
In case the OTCaccess set works offline the system might require a Close Code.A close
code is the guarantee that the door is really closed.
In case your system requires a Close Code Follow the steps:
6 www.bvktechnology.com
6. Press green tick button.
5. Enter your OTC.
Note: You should receive your 8-digit OTC
code by SMS/e-mail/phone call. Contact
your administration to get an OTC.
After 10 (default value, can vary) consecutive invalid
PIN/OTC entries the device enters 1st penalty mode.
1st penalty mode device behavior: For 180 seconds every
3 seconds. (default values, can vary) the device will make
a beep sound, keypad’s led will get blue and will not
accept any OTC entries. After 180 seconds, the device will
come back to operational state.
Penalty Mode
Note: Each your wrong PIN/OTC entry is recorded by the system. Do not forget that excessive
wrong entries will lead to penalty mode!
This practice is used in order to scare the thief.
7 www.bvktechnology.com
2. After the administrator
assures you that Close Code
was issued to the system,
press green tick button.
1. The close code will appear
automatically, after you success-
fully unlocked the door with an
OTC and afterwards locked the it
back, on the screen of the
keypad. Once you get this code
you should contact your administ-
ration and report the Close Code.
After 1st penalty mode is closed, in case 5 (default value,
can vary) more consecutive invalid PIN/ OTC entries are
done, the device enters 2nd penalty mode.
Once the device is in 2nd penalty mode it will not accept any
OTC entries unless a Penalty Mode Off OTC is entered to
the device.
To get a Penalty Mode Off OTC, contact your administrator.
1. Enter function code “04”.
2. Press green tick button.
3. Enter your PIN
4. Press green tick button.
2nd Penalty Mode
Once you get the code follow these steps:
8 www.bvktechnology.com
Altri manuali per otcaccess C5
1
Indice
