C-me Xcorpio Manuale utente
User’s Manual
User’s Manual
User’s Manual
Version 1.0
XcorpioXcorpio
www.cme-pro.com
Trademarks:
CME and Xcorpio are the registered trademarks of Central Music Co. All the other
trademarks belong to their respective owners.
FCC INFORMATION (U.S.A)
1.
IMPORTANT NOTICE: DO NOT MODIFY THIS UNIT!
This product, when installed as indicated in the instructions contained in this manual,
meets FCC requirements. Modi cations not expressly approved by CME may void
your authority, granted by the FCC, to use the product.
2.
IMPORTANT: When connecting this product to accessories and/or another product
use only high quality shielded cables. Cable(s) supplied with this product MUST be
used. Follow all installation instructions. Failure to follow instructions could void
your FCC authorization to use this product in the USA.
3.
NOTE: This product has been tested and found to comply with the limits for a Class
B Digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
environment. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used according to the instructions found in the users
manual, may cause interference harmful to the operation of other electronic devices.
Compliance with FCC regulations does not guarantee that interference will not occur
in all installations. If this product is found to be the source of interference, which
can be determined by turning the unit “OFF” and “ON”, please try to eliminate the
problems by using one of the following measures:
Relocate either this product or the device that is being affected by the interference.
Utilize power outlets that are on different branch (circuit breaker or fuse) circuits or install
AC line lter(s).
In the case of radio or TV interference, relocate/reorient the antenna. If the antenna lead-in
is 300 ohm ribbon lead, change the lead-in to co-axial type cable.
If these corrective measures do not produce satisfactory results, please contact the local
retailer authorized to distribute this type of product. If you cannot locate the appropriate
retailer, please contact CME.
The above statements apply ONLY to those products distributed in the USA.
Contents
Welcome!......................................................................4
Contents in the Xcorpio package....................................5
About the special accessories of Xcorpio........................5
Connections of Xcorpio..................................................6
Installation and Un-installation of the Xcorpio Driver......7
Installing the Driver..........................................................................................7
Uninstalling the Driver...................................................................................10
Control panel of Xcorpio...............................................11
Installing contral panel....................................................................................11
Removing contral panel..................................................................................13
Introduction of control panel..........................................................................13
Input Gain and Output Volume.......................................................................14
Hardware Monitoring.....................................................................................15
Skin Change....................................................................................................15
About .............................................................................................................15
Minimize and Close........................................................................................16
ASIO control panel.......................................................17
Speci cations..............................................................19
Xcorpio User's Manual
4
Welcome!
We’re pleased that you choose a CME audio interface product and would like
to congratulate you on your decision. With the Xcorpio Audio System, you’
ve purchased a sophisticated product representing the state of the art in studio
technology—and we’re convinced that this innovative development will prove
to be extremely useful to you in the coming years and, above all, provide you
with a great deal of entertainment.
We will explain this product and related technical issues based on practical
examples in the studio environment. We hope you nd this manual both
informative and entertaining to read, and hope you nd lots of enjoyment in the
Xcorpio system.
Xcorpio audio uses USB 2.0 as the interface to connect to your computer.
The High data transfer band width allows recording at high sampling rates via
USB. Ultra-high quality AD / DA converters captures all of the sound precisely.
The use of balanced signals pathes eliminates noise and cuts down on external
interference.
In the control panel of Xcorpio, users can select a suitable signal type for each
channel independently. It is very convenient for users to connect different
devices to each connector at the same time and select the right xed gain. For
more accurate monitoring, Xcorpio features not only line outputs but also a
headphone output with a hardware volume control. Moreover, the hardware
monitoring function makes monitoring easy and complete.
There are signal LEDs and clip LEDs on both input and output channels
to indicate the status of signals coming in and going out. The ASIO driver
is designed for use with USB and helps Xcorpio to work ef ciently. High
sampling rate recording tasks won’t be a problem with Xcorpio’s low latency
support even in multi-track recordings.
Xcorpio User's Manual
5
Contents in the Xcorpio package
Before installing Xcorpio, please make sure you found all the items in the
Xcorpio package as show below.
•
1 Xcorpio audio interface (Xcorpio A or Xcorpio I, depends on the model
you chose)
•
1 USB cable (about 1.8m)
•
1 protective pouch
•
1 metal clasp (including screw)
•
1 user’s guide (This manual)
•
1 driver CD
About the special accessories of Xcorpio
There are two special accessories in the Xcorpio package. One is the protective
pouch and the other one is the metal clasp. With the pouch, you can take the
Xcropio out and protect it from damage. In mobile condition, the metal clasp is
more helpful for usesr to hang Xcorpio on the belt or guitar strap.
If you want to use the clasp, please follow the steps below to assemble it.
1. Please take out the attached metal clasp and screw from the Xcorpio
package. Please note that you have to use the screws in the package. It
may damage the electrical circuit of Xcorpio if you use other screw, and
this kind of damage is not covered under warranty.
2. Lock the screw into the small hole slightly on the back of Xcorpio rst.
Then unlock the screw.
3. Put the metal clasp on the indent on the back of Xcorpio and lock it with
screw.
Xcorpio User's Manual
6
You can lock the metal clasp in different directions. (see above)
Connections of Xcorpio
The design of Xcorpio is simple and clear, users can get familiar with it in a
very short time. Below is the detail of Xcorpio’s connectors. (Below the Xcorpio
A is used as the example)
1. Headphone output (stereo, 3.5mm TRS)
2. Line output, left channel (un-balanced, RCA, black)
3. Line output, right channel (un-balanced, RCA, red)
4. Headphone volume control knob
5. Headphone output LEDs, green one is for signal LED, red one is for clip
LED.
6. Left input channel LEDs, green one is for signal LED, red one is for clip
LED.
7. Right input channel LEDs, green one is for signal LED, red one is for clip
LED.
Xcorpio User's Manual
7
8.
Analog input jack, left channel (balanced, XLR, black)
9.
Analog input jack, right channel (balanced, XLR, red)
10. USB port
Installation and Un-installation of the Xcorpio Driver
Note: Please do not connect Xcorpio to USB port of your computer before the
setup program requires you to do so.
Installing the Driver
Please insert the driver CD of Xcorpio into the CD-ROM drive of your
computer. The auto-run program will start up automatically. Click “Driver
Installation or Un-installation” to begin the installation procedure.
Note: The current installation program only supports
English, so just click OK to start installation.
Click the icon on the left of Install the driver to install driver.
Xcorpio User's Manual
8
Select I accept the agreement then click Install.
The Setup program will search to see if Xcorpio driver has
already been installed. If it nds a previous driver, the setup
program will un-install it rst. It will take a moment, so
please wait.
The Setup program asks you to connect the Xcorpio
to the computer. Please use a standard USB cable to
connect Xcorpio and computer now. You do not need to
click any button.
Xcorpio User's Manual
9
Once connected the Setup program will initialize Xcorpio,
which will take several minutes. Please wait.
Please unplug Xcorpio from USB port of computer.
The Setup program asks you to connect the Xcorpio again.
Please plug Xcorpio again.
Xcorpio User's Manual
10
Click Exit to complete the driver installation.
Once the driver installation is complete, the Xcorpio should appear as
“Xcorpio WDM Audio” in the “Sound, Video and game controllers” in the
Device Manager.
Uninstalling the Driver
Note: Before un-installing the driver, you have to un-plug the Xcorpio from
the computer.
It is the same procedure as driver installation, please run the setup program.
The current installation program only supports
English, click OK to start the procedure.
Questo manuale è adatto per i seguenti modelli
2
Indice
Altri manuali C-me Accessori
