Cairn FuraLED Manuale utente
Quick Start
FURALED
DUALPORT COUPLING
The FuraLED dual port coupling houses two UV LEDs (typically 340nm and 385nm for Fura-2, although a
Fura-8 variant is available), photodiodes providing optical feedback for each channel, excitation filters and
a dichroic mirror to split the two wavelengths.
Each LED has individual focus (Z), and XY adjustments to optimise output when connected to your micro-
scope.
This short guide details how to align your FuraLED coupling. For general power supply operation, please
refer to the OptoLED user manual.
For the purpose of this Quick Start, all words in bold blue refer to parts labelled in diagrams throughout
this document.
340nm
385nm
340nm LED X&Y
adjustments
385nm LED X&Y
adjustments
340nm LED
focus
385nm LED
focus
Quick StartQuick Start
1) Attach the coupling to your microscope
Cairn microscope adapters are either supplied to couple onto an existing epi-illuminator or are used in
place of the epi-illuminator as a ‘direct’ coupling.
a. If attaching to your existing epi-illuminator, a male bayonet coupling is normally supplied,
which attaches to your microscope epi-illuminator via a large grub screw.
2) Align and focus the 340nm LED at the back focal plane of the objective
** IMPORTANT SAFETY NOTE - UV LEDs ARE NOT VISIBLE BY EYE AND WILL CAUSE DAMAGE IF
LOOKED AT DIRECTLY.
ALWAYS VIEW THE LED LIGHT BY SHINING AT A PIECE OF WHITE PAPER AND VIEW THE
FLUORESCENCE AT A LOW POWER **
a. Move to a blank objective position on the objective nosepiece, remove any cover caps and
place a small piece of white paper in this position. Alternatively, place a centering tool in the
light path.
b. Ensure your Fura-2 cube is in place in your microscope.
c. Turn on the 340nm LED channel on the OptoLED controller
d. Using the 2.5mm allan key (provided), turn the 340nm LED focus until the image of the
LED comes into sharp focus on the paper, please refer to Figure 1 below.
e. Using the same 2.5mm allan key, centre the position of the 340nm LED using the 340nm
3) Repeat the steps above for X, Y and Z adjustment for the 385nm LED
Once the FuraLED channels have been aligned and focussed, the coupling should not need further ad-
justment unless removed from the microscope. We recommend periodically checking the alignment to
ensure your illumination is optimal.
Figure 1
Quick StartQuick Start
Coupling variation – FuraLED in reflected position of dual port coupling
When configured with an additional transmitted (longer wavelength) channel, the FuraLED coupling is
reflected via a dichroic mirror (typically 400LP). The same adjustments are present for each UV channel,
along with an additional mirror adjustment for both UV LEDs (if required) and X,Y,Z adjustments for the
transmitted channel.
W.White
340nm
385nm
Transmitted LED
X&Y
adjustments
Transmitted LED
focus
adjustment
FuraLED
horizontal
adjustment
FuraLED
vertical
adjustment
1) Align the 340nm and 380nm channels on the FuraLED as per the previous instructions
2) Perform any final positional adjustment (moving both UV LEDs equally) via the dichroic mirror
a. Adjust the FuraLED horizontal and vertical adjustments on the dual port coupling.
These may be via blue thumb screws (as in the image above) or using the 1.5mm
allan key supplied with current dual port couplings.
Quick Start
3) Focus and align the transmitted LED
a. Loosen the blue thumb screw which locks off the transmitted LED focus adjustment and
slide the LED head in Z within the coupling until the image of the LED comes into sharp
focus on the piece of paper (or centering tool). Lock off this position by
securing the thumb screw. A notch is present in the LED housing to help locate this
lock off screw and prevent the LED being fully pulled out of the coupling.
b. Adjust the position of the transmitted LED using the transmitted LED X and Y adjustment
thumb screws until centred.
Please contact us if you have any questions or issues during setup or operation
Indice
Altri manuali Cairn Microscopio
