Calculated Industries 4065 Construction Master Pro v3.0 Manuale utente

ONSTRUCTION

ASTER

User’s Guide

For Models:

4065 Construction Master Pro v3.0

4080 Construction Master Pro Trig v3.0

44080 Construction Master Pro Desktop v3.0

4065/4080 UG CVR ENGLISH_mod 7/21/04 10:43 AM Page 1

SER

’

UIDE

— 1

This User’s Guide helps you solve common construction math and

material estimation problems using the latest

Construction Master Pro

calculators—three of the most powerful feet-inch-fraction calculators

to date:

The

Construction Master Pro III

Series —

1. Construction Master Pro v3.0 (#4065)

2. Construction Master ProTrig v3.0 (#4080)

3. Construction Master Pro Desktop v3.0 (#44080)

IMPORTANT: The

Construction Master Pro Trig

does not have

Block, Concrete Footing, Drywall, or Length, Width, and Height

functions. These keys are replaced with standard trigonometric keys.

ONSTRUCTION

ASTER

3.0

SER

’

UIDE

4065UG-E-B 6/9/04 1:49 PM Page 1

2 — C

ONSTRUCTION

ASTER

/ T

RIG

/ D

ESKTOP

The

Construction Master Pro

line includes the most advanced feet-

inch-fraction calculators

designed specifically for building pro’s!

The

Pro

calculators handle practically any problem involving meas-

urements and can be used to save time, prevent errors, and accu-

rately perform common building projects such as: estimating con-

crete volume, squaring-up foundations, framing roofs, ordering lum-

ber, building stairs, walls, laying driveways, carpet or floor covering,

figuring precise angle calculations, or simply working in feet-inch-

fractions or decimal feet!

Your Calculator Helps You Solve:

• Dimensional Math Problems

• Conversions Between Feet-Inch-Fractions, Decimal Feet,

Decimal Inches, and Yards

• Imperial/Metric Conversions

• Problems Involving All Common Fractions —

1/2” to 1/64”!

• Area/Volume Calculations

• Board Feet/Lumber Calculations

• Circle Calculations

• Column/Cone Area and Volume

• Compound Miter Cuts for Crown Moulding

• Material Estimations and Costs

• Polygons

• Rake-Walls

• Right Angle/Triangle Solutions

• Roofing Materials

• Stair Layout (Risers/Treads)

• Studs

• Weight/Volume Conversions

Pro and Desktop Models (

NOT AVAILABLE ON TRIG MODEL

#4080)

Also Solve:

• Block/Bricks, Concrete Footings and Drywall

• Instant Square-up, Perimeter, Wall Area, Room Area and

Volume

INTRODUCTION

4065UG-E-B 6/9/04 1:49 PM Page 2

SER

’

UIDE

— 3

GETTING STARTED..........................................................................8

KEY DEFINITIONS .........................................................................8

Basic Operation Keys ..................................................................8

Convert ÇKey –

Unit Conversions and Second Functions

....8

Memory and Storage Functions...................................................9

Recall ®Key...........................................................................10

Dimensional Measurement Unit Keys........................................10

Area and Volume Keys (NOT AVAILABLE ON TRIG MODEL #4080)....11

Weight Keys...............................................................................12

Construction Project Keys..........................................................13

Block/Brick Keys (NOT AVAILABLE ON TRIG MODEL #4080)..............13

Circular/Arc Function Keys ........................................................13

Column/Cone Key......................................................................15

Compound Miter/Crown Moulding Keys....................................15

Drywall Keys (NOT AVAILABLE ON TRIG MODEL #4080)....................16

Footing Keys (NOT AVAILABLE ON TRIG MODEL #4080) ...................16

Polygon Key...............................................................................16

Right Triangle/Roof Framing Keys.............................................17

Hip/Valley and Jack Rafter Keys................................................18

Rake-Wall Function....................................................................20

Roof Materials/Covering Keys ...................................................21

Stair Key ....................................................................................21

Studs..........................................................................................23

Trigonometric Keys (TRIG #4080 AND DESKTOP #44080

MODELS ONLY)...........................................................................23

ENTERING DIMENSIONS............................................................25

Entering Linear Dimensions.......................................................25

Entering Square/Cubic Dimensions...........................................25

SETTING FRACTIONAL RESOLUTION.......................................27

Setting Fraction Resolution –

Using the Preference

Setting Mode

...........................................................................27

Setting Fraction Resolution –

Using

Ç..................................28

Converting Fractional Value to Different Resolution..................28

Setting Fixed/Constant Fractional Resolution............................29

CONVERSIONS (LINEAR, AREA, VOLUME) ..............................30

Linear Conversions....................................................................30

Converting Feet-Inch-Fractions to Decimal Feet.......................30

Converting Decimal Feet to Feet-Inch-Fractions.......................30

Converting Fractional Inches to Decimal Inches.......................31

TABLE OF CONTENTS

4065UG-E-B 6/9/04 1:49 PM Page 3

4 — C

ONSTRUCTION

ASTER

/ T

RIG

/ D

ESKTOP

Converting Decimal Inches to Fractional Inches.......................31

Square Conversions ..................................................................31

Cubic Conversions.....................................................................31

PERFORMING BASIC MATH WITH DIMENSIONS.....................32

Adding Dimensions....................................................................32

Subtracting Dimensions.............................................................32

Multiplying Dimensions..............................................................32

Dividing Dimensions ..................................................................32

Percentage Calculations............................................................33

MEMORY OPERATION ................................................................33

Basic Cumulative Memory (M+).................................................34

Permanent Storage Registers (M1 and M2)..............................34

PAPERLESS TAPE OPERATION.................................................35

EXAMPLES –

USING THE CONSTRUCTION MASTER PRO

......37

LINEAR MEASUREMENT EXAMPLES........................................37

Adding Linear Measurements....................................................37

Cutting Boards...........................................................................37

Window Measurement...............................................................38

Calculating the Center Point......................................................38

AREA CALCULATIONS ................................................................39

Square Area (x2) ........................................................................39

Area of a Rectangular Room (LxW) ..........................................39

Using Multi-Function WKey to Find Area, Square-up and

Perimeter (NOT AVAILABLE ON TRIG MODEL #4080)......................39

VOLUME CALCULATIONS...........................................................40

Rectangular Containers (LxWxH)..............................................40

Using the Multi-Function hKey to Find Volume, Area,

Square-Up, Perimeter, Wall Area and Room Area

(NOT AVAILABLE ON TRIG MODEL #4080) ......................................40

Volume of a Cylinder..................................................................41

Volume of a Cone ......................................................................41

WEIGHT/VOLUME CONVERSIONS............................................42

Weight Conversions...................................................................42

Weight per Volume/Volume Conversions...................................42

BLOCKS/BRICKS (NOT AVAILABLE ON TRIG MODEL #4080)...............43

Number of Blocks, Based on Calculated Area .........................43

Number of Blocks, Based on Entered Area...............................43

Number of Blocks, Based on Calculated Perimeter ..................44

Number of Blocks, Based on Length.........................................44

Number of “Face” Bricks ...........................................................45

Number of “Paver” Bricks .........................................................45

4065UG-E-B 6/9/04 1:49 PM Page 4

SER

’

UIDE

— 5

BOARD FEET –

LUMBER ESTIMATION

.....................................46

Total Board Feet –

With Dollar Cost

..........................................46

Number of Board Feet Based on Entered Volume....................46

CIRCLE AND ARC CALCULATIONS............................................47

Circumference and Area of a Circle...........................................47

Arc Length –

Degree and Diameter Known

...............................47

Arc Length –

Degree and Radius Known

..................................47

Arc Calculations –

Arc Length and Diameter Known

................48

Arched/Circular Rake-Walls –

Chord Length and Segment Rise

Known

.....................................................................................49

Arched Windows........................................................................50

COMPOUND MITER.....................................................................51

Compound Miter Cuts................................................................51

CONCRETE/PAVING....................................................................52

Volume of Concrete for a Driveway...........................................52

Concrete Columns.....................................................................53

Complex Concrete Volume........................................................54

Polygon, Finding Angles Based on Entered Radius and

Number of Sides.....................................................................55

Concrete Footings (NOT AVAILABLE ON TRIG MODEL #4080)...........56

Squaring-up a Foundation .........................................................57

DRYWALL (NOT AVAILABLE ON TRIG MODEL #4080)...........................58

Number of Drywall Sheets for a Given Area..............................58

Number of Drywall Sheets for a Given Length..........................58

GRADE/SLOPE.............................................................................59

Back-Fill on a Slope –

Percent of Grade Known

.......................59

RIGHT TRIANGLE AND ROOF FRAMING EXAMPLES..............60

Roof Framing Definitions ...........................................................61

Degree of Pitch..........................................................................63

Percent Grade............................................................................63

Pitch Ratio or Slope...................................................................63

Common Rafter Length..............................................................64

Common Rafter Length –

Pitch Unknown

.................................64

Angle and Diagonal (Hypotenuse).............................................65

Rise............................................................................................65

Rise and Diagonal......................................................................65

Sheathing Cut............................................................................66

Regular Hip/Valley and Jack Rafters ........................................66

Jack Rafters –

Using Other Than 16 Inch On-Center

Spacing

..................................................................................67

4065UG-E-B 6/9/04 1:49 PM Page 5

6 — C

ONSTRUCTION

ASTER

/ T

RIG

/ D

ESKTOP

Irregular Hip/Valley and Jack Rafters –

Descending, with

On-Center Spacing Maintained

..............................................68

Irregular Hip/Valley and Jack Rafters –

Ascending, with

Jacks Mating at Hip/Valley

......................................................70

Rake-Wall –

No Base

.................................................................72

Rake-Wall –

With Base

..............................................................73

ROOFING MATERIALS ................................................................74

Roof Covering –

Entering Pitch, Length and Width

..................74

Roof Covering –

Entering Rise, Run (No Pitch) and Area

.........75

STAIR LAYOUT EXAMPLES ........................................................76

Stair Layout Definitions..............................................................76

Stairs –

Given Only Floor-to-Floor Rise

.....................................78

Stairs –

Given Only the Run

......................................................80

Stairs –

Given Rise and Run

.....................................................81

Stairs –

Given Rise and Run, Using “Riser Limited” Function

for Code Restrictions

..............................................................82

Baluster Spacing........................................................................83

STUDS..........................................................................................84

BASIC D:M:S AND TRIGONOMETRY EXAMPLES.....................84

Converting Degrees:Minutes:Seconds ......................................84

Time Calculations Using D:M:S.................................................84

TRIGONOMETRIC FUNCTIONS..................................................85

Converting Percent Grade to D:M:S..........................................86

Converting Tangent/Pitch to Angle.............................................86

Converting Roof Angle in Degrees to Pitch in Inches................86

Angle –

Rise and Hypotenuse Known

.......................................87

APPENDIX A –

DEFAULT SETTINGS

............................................88

APPENDIX B –

PREFERENCE SETTINGS

....................................89

How to Set Preferences.............................................................91

Accessing Preference Settings..................................................92

APPENDIX C –

CARE INSTRUCTIONS

.........................................94

APPENDIX D –

IMPORTANT NOTES FOR OWNERS OF

PREVIOUS CONSTRUCTION MASTERS

..................................95

APPENDIX E –

ACCURACY/ERRORS, AUTO SHUT-OFF,

BATTERIES, RESET

....................................................................96

ACCURACY/ERRORS..................................................................96

Error Codes................................................................................96

AUTO SHUT-OFF .........................................................................96

BATTERIES...................................................................................97

Replacing the Battery(ies)..........................................................97

Battery Replacement Instructions..............................................97

4065UG-E-B 6/9/04 1:49 PM Page 6

SER

’

UIDE

— 7

RESET KEY..................................................................................97

APPENDIX F –

AREA/VOLUME FORMULAS

................................98

AREA FORMULAS........................................................................98

SURFACE AREA/VOLUME FORMULAS .....................................99

REPAIR AND RETURN .................................................................100

WARRANTY...................................................................................101

INDEX.............................................................................................104

4065UG-E-B 6/9/04 1:49 PM Page 7

8 — C

ONSTRUCTION

ASTER

/ T

RIG

/ D

ESKTOP

KEY DEFINITIONS

Basic Operation Keys

On/Clear

— Turns power on. Pressing once clears

the display. Pressing twice clears all temporary

values.

OTurns all power off, clearing all non-permanent

registers.

+ – x Arithmetic operation keys.

÷ =

%Four-function (+, -, x, ÷) percent key. (See page 33

for examples.)

0– 9and •Keys used for entering digits.

)(DESKTOP ONLY)Enters “00” to save keystrokes (e.g.,

1 ) to enter 100).

Backspace Key

— Used to delete entries one key-

stroke at a time (unlike the ofunction, which

deletes the entire entry).

Convert ÇKey —

Unit Conversions and Second Functions

The Çkey is to convert between measurement units or to access

the second functions listed below:

Ç x

Clear All

— Clears all values, including Memory.

Resets all permanent entries to default values

(except Preference Settings which are retained).

Note: Use only when necessary, as it resets all stored values to

factory defaults. See page 88 for a listing of default values.

Ç %

— Squares the value in the display. For example,

to square the value 10, enter 1 0 then Ç %.

Ç B

Square Root Function ( )

— Used to find the

square root of a non-dimensional or area value

(e.g., 1 0 0 Ç B = 10).

Ç /

x10y

— Allows entry of an exponent. For example,

8 Ç / 1 4 is 8 times 10 to the 14th power.

GETTING STARTED

4065UG-E-B 6/9/04 1:49 PM Page 8

SER

’

UIDE

— 9

Ç ÷

1/x

— Finds the reciprocal of a number (e.g., 8

Ç ÷ = 0.125).

Ç –

Change Sign (+/–)

— Toggles the sign of the dis-

played value to positive or negative.

Ç +

Pi (

)

— Constant = 3.141593

Ç •

Degrees:Minutes:Seconds

— Converts between

D:M:S and decimal degree formats.

Ç 0

Total Cost

— Calculates total material cost given a

unit dimension and an entered Per Unit Cost.

Ç ß

Access Preference Settings

— Used to access

various customizable settings, such as dimensional

answer formats (see Preference Settings on page

89).

Memory and Storage Functions

Your calculator has two types of Memory:

1) basic memory or semi-permanent, cumulative µ;

2) non-cumulative Storage Registers (M1-M3).

Semi-Permanent Memory

— Adds any displayed

number, dimensioned or unitless, to the semi-per-

manent, cumulative Memory. Values can be sub-

tracted from this Memory using Ç µ

(M–)

. ®

µwill display the value in the Memory. ® ®

will display and clear the value in the Memory. Ç

®will clear the cumulative Memory without dis-

turbing the existing display.

ß 1 – 3

Storage Registers (M1) through (M3)

— Stores

the displayed value in non-cumulative, permanent

Memory (e.g., 1 0 ß 1). Good for storing a

single value, for future reference (® 1 = 10).

Note: Non-cumulative means it only accepts one value (does not

add or subtract) and a second entered value will replace the first.

Permanent means the value is stored even after the calculator is

shut off. To delete a stored value, enter a new value or perform a

Clear All

Ç x

4065UG-E-B 6/9/04 1:49 PM Page 9

Altri manuali per 4065 Construction Master Pro v3.0

Indice

Altri manuali Calculated Industries Calcolatrice

Calculated Industries

Calculated Industries 8305 KitchenCalc Pro Manuale utente

Calculated Industries

Calculated Industries Quilter's FabriCalc 8400 Manuale utente

Calculated Industries

Calculated Industries KitchenCalc 8300 Manuale utente

Calculated Industries

Calculated Industries PIPE TRADES PRO 4095 Manuale utente

Calculated Industries

Calculated Industries Quilter's FabriCalc 8400 Manuale utente

Calculated Industries

Calculated Industries 4054 Manuale utente

Calculated Industries

Calculated Industries PIPE TRADES PRO 4095 Manuale utente

Calculated Industries

Calculated Industries Construction Master 5 4050 Manuale utente

Calculated Industries

Calculated Industries ConstructionMaster HeavyCalc 4320 Manuale utente

Calculated Industries

Calculated Industries 3423 Manuale utente

Calculated Industries

Calculated Industries 3265 Manuale utente

Calculated Industries

Calculated Industries 3405 Manuale utente

Calculated Industries

Calculated Industries ProjectCalc Plus MX 8528 Manuale utente

Calculated Industries

Calculated Industries ULTRA MEASURE MASTER 8025 Manuale utente

Calculated Industries

Calculated Industries 8015 Manuale utente

Calculated Industries

Calculated Industries 8509 Manuale utente

Calculated Industries

Calculated Industries Frame Master II Manuale utente

Calculated Industries

Calculated Industries 3416 Manuale utente

Calculated Industries

Calculated Industries Material Estimator Manuale utente

Calculated Industries

Calculated Industries Construction Master IV Manuale utente

Calculated Industries

Calculated Industries ULTRA MEASURE MASTER 8020 Manuale utente

Calculated Industries

Calculated Industries 4088 Manuale utente

Calculated Industries

Calculated Industries 3420 Manuale utente

Calculated Industries

Calculated Industries Pocket Handyman IV Manuale utente

Manuali Calcolatrice popolari di altre marche

HP 35s Manuale

Casio

Casio CFX-9970G Manuale utente

LEXIBOOK

LEXIBOOK EL350 Manuale utente

HP HP-97 Manuale utente

Citizen

Citizen SDC-414N Manuale utente

Casio

Casio fx-3800P Manuale utente

Canon

Canon P26-DHIII Manuale utente

Citizen

Citizen 520DPA Manuale utente

Sharp

Sharp EL-9900 Manuale utente

Casio

Casio FX-9860GII - SOFTWARE VERSION 2-00 Manuale utente

Casio

Casio MS-7UC Manuale utente

Sharp

Sharp WriteView EL-W506 Manuale tecnico

Casio

Casio FC-200 Manuale utente

Casio

Casio fx-CG50 Manuale utente

HP HP-67 Guida utente

Royal

Royal CBC2000 Manuale utente

Heathkit

Heathkit IC-2009 Manuale utente

Universal

Universal UNV-15907 Manuale utente