Calculated Industries Construction Master IV Manuale utente
CONSTRUCTION MASTER®IV
For Today's Construction Professional
User’s Guide
2 — Construction Master IV
Table of Contents
The Construction Master®IV...........3
GETTING STARTED...........................4
Key Definitions/Functions................4
Fractional Settings.........................13
Entering Dimensions.....................14
Basic Math Operations..................16
Percentage Calculations ...............18
Memory Operation.........................19
Paperless Tape.............................20
EXAMPLES.......................................22
Linear Calculations........................22
Area Calculations..........................24
Volume Calculations .....................27
Volume/Weight Calculations ........31
Board Feet/ Lumber Calculations..32
Right-Triangle Calculations..........32
Hip/Valley & Jack Rafters..............39
Stair Problems (Risers/Treads)....43
Circle Problems.............................46
Appendix A.......................................47
Battery & Auto Shut-Off.................47
Default Values...............................47
Appendix B.......................................48
Repair and Return ...........................50
Warranty...........................................51
User's Guide — 3
THE CONSTRUCTION MASTER®IV
Designed for today’s construction pro-
fessional, the Construction Master®IV
is so simple, even the novice user will
find it easy to solve hundreds of di-
mension-related problems right in feet,
inches and fractions!
♦Solve Dimensional Math
♦English/Metric Conversions
♦Calculate Areas/Volumes
♦Solve Right-Triangle Problems
♦Find Regular and Irregular Hip,
Valley and Jack Rafters
♦Calculate Stair Risers, Treads
and Stringers
♦Solve Raked Wall Stud Lengths
♦Volume/Weight Conversions
♦Estimate Board Feet
♦Find Circular Areas,
Circumferences and Arcs
♦Material Estimations
♦Paperless Tape Function
♦And much, much more!
4 — Construction Master IV
GETTING STARTED
Key Definitions/Functions
Basic Function Keys
[+] [–] [x] [÷] [=]
Arithmetic operation keys.
[%]
Four-function percent key.
[0] – [9] and [ • ]
Digits used for keying-in numbers.
[Off] — Off Key
Turns all power off, clearing all non-
permanent registers.
[On/C] — On/Clear Key
Turns on power. Pressing once
clears the display. Pressing twice
clears all temporary values.
[Conv] — Convert Key
Used with the dimensional keys to
convert between dimensions or with
other keys to access special func-
tions.
[] — Square Root Key
Used to find the square root of a
non-dimensional or area value.
User's Guide — 5
[Conv] [ ] — x2Function
Finds the square of a linear or non-
dimensional value.
[M+] — Memory Key
Adds the displayed value to Mem-
ory. Clears when the calculator is
shut off.
[Conv] [M+] — Memory Minus (M–)
Subtracts the displayed value from
Memory.
[Conv] [Rcl] — Memory Clear
Clears Memory without changing
current display.
[Rcl] — Recall Key
Used with other keys to recall stored
values and settings.
[Rcl] [x] — Imperial/Metric Mode
Changes the defaults of the calcula-
tor by setting to Imperial (English) or
Metric mode. Note: This setting is
not affected by the ALL CLEAR
function.
6 — Construction Master IV
Dimension Keys
[Weight] — Weight Key
Enters or converts (a volume value)
to tons, pounds, metric tons or kilo-
grams. Repeated presses will cycle
through these units.
[Conv] [%] — Weight/Volume
Enters or converts the Weight per
Volume setting as Tons/Yard³,
Lbs/Yd³, Lb/Ft³, Metric Ton/m³ or
kg/m³. Repeated presses will cycle
through these settings.
[Cu] — Cubic Key
Defines a volume (e.g., 5 [Cu]
[Yds]).
[Sq] — Square Key
Defines an area (e.g., 5 [Sq][Feet]).
[Yds] — Yards Key
Enters or converts to yards.
[Feet] — Feet Key
Enters or converts to feet as whole
or decimal numbers. Also used with
the [Inch] and [/] keys for entering
Feet-Inch values (e.g., 6 [Feet] 9
[Inch] 1 [/] 2). Repeated presses
toggle between Feet-Inch and Deci-
mal Feet.
User's Guide — 7
[Inch] — Inch Key
Enters or converts to inches. Entry
can be whole or decimal numbers.
Also used with the [/] key for enter-
ing fractional inch values (e.g., 9
[Inch] 1 [/] 2). Repeated presses
during conversions toggle between
Fractional and Decimal Inches.
[ / ] — Fraction Bar Key
Used to enter fractions. Fractions
can be entered as proper (1/2, 1/8,
1/16) or improper (3/2, 9/8). If the
denominator (bottom) is not entered,
the calculator's fractional accuracy
setting is automatically used.
[m] — Meter Key
Enters or converts to meters.
[cm] — Centimeter Key
Enters or converts to centimeters.
[mm] — Millimeter Key
Enters or converts to millimeters.
[Bd Ft] — Feet Key
Enters or converts cubic values to
board feet. One board foot is equal
to 144 cubic inches (1 foot x 1 foot x
1 inch).
8 — Construction Master IV
Right Triangle/Rafter Keys
[Pitch]
This key is used to enter or calculate
the pitch (slope) of a roof (or right tri-
angle). Pitch is the amount of "Rise"
over 12 inches (1 meter, if metric) of
"Run." Pitch may be entered as:
a dimension 9 [Inch] [Pitch]
an angle 30 [Pitch]
a ratio 0.75 [Conv] [Pitch]
a percentage 75 [%] [Pitch]
A pitch entry will remain in perma-
nent storage until revised or reset. A
solution will be replaced by its en-
tered value once the calculator is
cleared.
[Rise] — Rise Key
Enters or calculates the rise or verti-
cal leg (height) of a right triangle.
[Run] — Run Key
Enters or calculates the run or hori-
zontal leg (base) of a right triangle.
[Diag] — Diagonal Key
Enters or calculates the common or
diagonal leg (hypotenuse) of a right
triangle. Typical applications are
“squaring" slabs or finding common
rafter lengths.
User's Guide — 9
[Conv] [Diag] — Rake Walls
This function finds the decreasing
stud sizes in a raked wall based on
computed or entered values for
pitch, rise and/or run. Repeated
presses display stud sizes from
longest to shortest.
The on-center spacing of a raked
wall can be permanently stored by
entering a dimension prior to solving
for stud sizes (12 [Inch] [Conv]
[Diag]). Default on-center spacing is
16 inches (Metric Mode: 600 mm).
[Hip/V] — Hip/Valley Rafter Key
Finds the regular or irregular hip/
valley rafter length. If an irregular
pitch is entered, the irregular hip/
valley rafter length is displayed, oth-
erwise the regular (45º) hip/ valley
rafter length is displayed.
[Conv] [Hip/V] — Irregular Pitch
Enters and displays the irregular
pitch value used to calculate lengths
of the irregular hip/valley and jack
rafters.
10 — Construction Master IV
[Jack] — Jack Rafter Key
Finds the jack rafter sizes – from
largest to smallest – for both regular
and irregular pitched roofs. The ini-
tial jack rafter values displayed are
from the regular pitched side. After
showing the minimum value, the cal-
culator will display the sizes for the
irregular pitched side. An on-center
spacing can be entered by pressing
[Jack] (i.e., 12 [Inch] [Jack]). The
default spacing is 16 inches (Metric
Mode: 600 millimeters).
[Conv] [Jack] — Irregular Side Jacks
Operates same as [Jack], but dis-
plays the irregular pitched side jack
rafters first. The calculator uses the
same on-center spacing as the regu-
lar pitch sided jack rafters unless a
new on-center spacing is entered
(e.g., 19.2 [Inch] [Conv] [Jack]).
Altri manuali per Construction Master IV
3
Indice
Altri manuali Calculated Industries Calcolatrice
Calculated Industries
Calculated Industries ScheduleCalc Manuale utente
Calculated Industries
Calculated Industries ULTRA MEASURE MASTER 8020 Manuale utente
Calculated Industries
Calculated Industries Mortgage PaymentCalc 3401 Manuale utente
Calculated Industries
Calculated Industries Construction Master 5 Manuale utente
Calculated Industries
Calculated Industries Measure Master 4018 Manuale utente
Calculated Industries
Calculated Industries Machinist Calc 4086 Manuale utente
Calculated Industries
Calculated Industries SCALE MASTER CLASSIC 6020 Manuale utente
Calculated Industries
Calculated Industries 3265 Manuale utente
Calculated Industries
Calculated Industries CONVERSIONCALC PLUS Manuale utente
Calculated Industries
Calculated Industries 8525 Manuale utente
Calculated Industries
Calculated Industries ULTRA MEASURE MASTER 8025 Manuale utente
Calculated Industries
Calculated Industries Measure Master 4018 Manuale utente
Calculated Industries
Calculated Industries PROJECTCALC Manuale utente
Calculated Industries
Calculated Industries Hot Rod Calc 8703 Manuale utente
Calculated Industries
Calculated Industries 4088 Manuale utente
Calculated Industries
Calculated Industries 3430 Manuale utente
Calculated Industries
Calculated Industries Construction Master ConcreteCalc Pro 4225 Manuale utente
Calculated Industries
Calculated Industries Ultra Scale Master 6250 Manuale utente
Calculated Industries
Calculated Industries ConstructionMaster HeavyCalc 4320 Manuale utente
Calculated Industries
Calculated Industries Construction Master IV Manuale utente
