Caleg WOWMAKER M 130 Istruzioni operative
General Operating Instructions
M130.2.1EN
2
I. Quick Start Guide ..................................................................3
II. Introduction and Important Terms .........................................4
III. Flightcase .............................................................................5
IV. Studiolifter............................................................................6
V. Studioframe..........................................................................7
VI. Transport ..............................................................................8
VII. Set-Up ..................................................................................9
VIII. Starting the LED Display......................................................13
IX. Dismantling the WOWMAKER..............................................15
X. Care and Maintenance.........................................................17
XI. Important Information.........................................................18
XII. Troubleshooting ..................................................................19
XIII. Features and Specifications ................................................21
XIV. Cabling and Wiring ..............................................................25
Table of Contents
Please read these instructions carefully before first use.
In order to connect and operate the WOWMAKER M130 safely, you must
read and understand the operating instructions!
i
Static calculation from June 15, 2018, SuS-Ingenieure mbH, Ettlingen
© 06.2018 caleg Schrank und ehäusebau mbH
WOWMAKER is a brand of
caleg Schrank und ehäusebau mbH
Zum erlen 1
D - 66131 Saarbrücken
Phone +49 6893 89 470
Mail your@wowmaker.de
Internet www.wowmaker.de
Validity of this document:
The release status of this user manual is shown on the title page and is only
valid in connection with a WOWMaker of the same release status.
You can also find an overview at www.wowmaker.de/release.
Subject to technical changes.
3
I. Quick Start Guide
The Quick Start uide is a condensed version of the user guide for experienced users.
It does not replace the user guide.
Check the transport dimensions, floor load and fuses at the installation location..
4 See page 21 4 See drawing page 24
The Flightcase has four inner and four outer wheels.
The inner wheels must always have contact with the ground.
When transported on a tail lift, the four outer wheels can overhang.
4 See page 8
When the WOWMAKER has reached its designated location, first lift off the rear case and then the
front case. At least two people are required to remove the cases.
4 See page 9
Place both cases upright against each other on the floor and lock them against each other with
the butterfly locks.
4 See page 12
Check that all connections are plugged in and locked.
Connections to the socket strip:
• 1x Neutrik power cable 4 See page 25
• 2x Neutrik plugs from the display 4 See page 25
• S-Box power supply unit on socket strip 4 See page 25
• 1x power cable for Lifter control 4See page 25
Connections S-Box:
• S-Box connection with power supply unit 4See page 25
• Network cable between S-Box and display 4See page 25
Lower the device’s foot and bring the Lifter to the presentation height.
4 See page 11
Remove the slide-in panel and roll the floor of the case away to the front.
4 See page 12
The WOWMAKER is now ready for presentation and media from the S-Box’s hard disk can be
shown on the display.
If desired, other media can be connected to the S-Box via cable.
4 See page 13
1
2
3
4
5
6
7
8
4
II. Introduction and Important Terms
The WOWMAKER M130 (hereinafter referred to as WOWMAKER) is an easy-to-use plug and play solution for
the SAMSUN IF 1.5 system. It combines a mobile LED Full HD display with a lift and transport system.
It consists of 3 main components, which together make up the WOWMAKER:
1. Flightcase
The flightcase is used to transport the display system safely and easily.
2. Studiolift
The Studiolifter is an adjustable electrical lifting system.
3. Studioframe
The Studioframe is a 130 zoll (approx. 330cm) Full HD (IF-1.5mm) Samsung display.
The following is also included in delivery:
Neutrik power cable - used to connect the WOWMAKER to the 220 V power supply system (page 10)
Cable remote control - for controlling the Studiolifter (page 11)
S-Box - UHD video processor for signal processing (page 13)
Remote control - for operating the S-Box (page 13)
S-Box power supply - for powering the S-Box (page 14)
IR Extender, consisting of the IR transmitter box, the IR eye and a power supply unit (page 14)
ATTENTION: The device is only for indoor use!
If you pass the device on to a third party, please make sure they receive these operating instructions, as well
as all accessories supplied with the WOWMAKER. This includes all of the written documents supplied, as
they are also part of the operating instructions.
This device may not be used by people with impaired physical, sensory or mental abilities or by children,
unless supervised by a person responsible for their safety.
Original WOWMAKER accessories can be found at: www.wowmaker.de/equipment
5
ATTENTION: During transport, make sure that the flightcase is not tilted sideways by more than 9
degrees.
III. Flightcase
The Flightcase is designed to fit through a door with a width of 85cm and a standard height of 200cm. Due
to its dimensions and weight (~750kg including Studiolifter and Studioframe) at least 2 people are required
to move the WOWMAKER.
If a loading ramp or a forklift is available on site, a small van with a loading area of at least 302cm is sufficient.
Otherwise, a 7.5t truck with a lifting platform should be used.
ATTENTION: Observe the load limits of the tail lift.
Weight empty approx. 250kg; weight with WOWMAKER approx. 750kg
1 1
2 222 2 2
2
FRONT
BACK
1Corner castor wheels with brakes 2Butterfly locks
6
IV. Studiolifter
The Studiolifter is controlled by a wired remote control. Optionally, a permanently connected control unit with
digital height display can also be purchased for the device.
The motors in the lifting columns are not intended for constant changes in the height position of the display.
The motion sequence should not exceed 4 minutes. Afterwards, a pause of at least 18 minutes must be
observed. A slight oil smell may develop during lifting or lowering.
7
V. Studioframe
The Studioframe consists of 18 single modules (three lines of six modules each) and one S-Box (UHD video
processor). The modules have FULL FRONT service access.
Do not touch the LED front with objects or dirty hands. This can irreparably damage the front boards.
Display wiring
(marked red)
(marked blue)
8
VI. Transport
ATTENTION: The Flightcase has four inner and four outer wheels. The inner wheels must always
have contact with the ground. When transported on a tail lift, the four outer wheels can overhang.
9
VII. Set-Up
Move the WOWMAKER to its intended position. This must be flat and able to support ~ 750kg, which corres-
ponds to a floor load of ~ 600kg/m².
ATTENTION: During transport, make sure that the Flightcase is not tilted sideways by more than 9 de-
grees. Installation at maximum angle of 3 degrees.
STEP 1: Once the WOWMAKER has reached its intended position, remove the rear part of the Flightcase
(wider one). To do so, open the ten butterfly locks. If necessary, the WOWMAKER can now be repositioned.
ATTENTION: At least two people are required to remove the case. Otherwise there is a risk of
accidents. Set the rear part of the case down carefully.
STEP 2: Open the butterfly locks on the front part of the case. Remove the front part of the case and set it
down carefully.
10
STEP 3: Open the back door of the Studiolifter. Insert the cable end with the Neutrik plug from the outside in
through the brush strip and connect it to the socket strip.
Lock in place with a 1/8 turn and insert the wired remote control from the inside out. Close the door again
(does not have to be locked).
ATTENTION: If the power supply is protected with 16A, the supplied Neutrik power cable can be
used to power the multi outlet for both circuits of the display. Alternatively, both display circuits can
be protected separately with 10A each.
ATTENTION: Make sure that the cables are not pinched!
Indice
