Cama HANDI-LIFT 7 Manuale utente
INSTALLATION MANUAL
FOR HANDI-LIFT 7
Handi-lift 7
2010 Page 1 Version 1.0
Table of contents
1
Introduction 2
1.1
Check the parts and drawing: 2
1.2
Electrical installation: 2
2
Forces on the building 3
3
Install the rails
3.1
Column installation:
3.2
Upper and lower rail installation:
Installing the lift unit 8
.1
Place the lift unit on the rail: 8
.2
Connect the electrical: 11
.3
Load cell adjustment: 11
.
Handicap symbol 11
5
Installation Test Certificate Cama Lifts 12
Handi-lift 7
2010 Page 2 Version 1.0
1Introduction
1 1 Check the parts and drawing:
Before you start installing please read this installation manual.
Check the received parts for transport damage.
Next, study carefully the installation drawing that comes with the lift to ensure that all
angels and dimensions are correct and all dimensions are there.
1 2 Electrical installation:
If the drawing does not show where to install the Control boxes, please sort out where
they all go. And make sure that the electrical supply and electrical wiring for the Handi-
Lift are there before installing the rail or columns.
You need 1x220V + earth protected by a 10 Amp fuse.
We recommend that you make a measurement of the earth connection.
Handi-lift 7
2010 Page 3 Version 1.0
Wall Mounted Rail
1. The top (Main) rail fixings are M10x160mm studs & 'Rawl' R-KF2 Kemfast Resin into
the wall.
2. The Lower rail fixings must be made using No.12x75mm csk screws & rawlplugs.
There are 250mm between the fixing bolts in the rail.
The bending strength in the rail will spread the force to 3 bolts
and the load in each bolt is therefore 1/3 x Fh
Stanchion Mounted Rail
1. Support stanchions must be fixed to concrete landing and treads, concrete strength
assumed to be 30N/mm2
2. Fixings used are M8 ramset 'Dynabolt'.
3. Pull out forces is 3.3kn and push in forces is .2kn
2Forces on the building
Handi-lift 7
2010 Page Version 1.0
3Install the rails
3 1 Column installation:
If the Handi-Lift is installed on columns you have to start with them.
Place the columns after the measurements on the drawing they are usually numbered
with the lowest number at the foot of the stairs.
When installing the columns be accurate that the columns are plum.
3 2 Upper and lower rail installation:
The rail system contains two types of rail, one for the lower rail and one for the upper
rail. If the upper rail is divided start to assemble the rail by using the assembly fittings
for rail. The lower rail does not need to be assembled before it is installed.
Mark measurement A from
the first and last raise parallel
with the staircase.
(See fig 2 on next page).
Note!
Some lifts has a different
angel than the staircase.
Handi-lift 7
2010 Page 5 Version 1.0
fig. 2
Mark measurement B
Mark measurement C from the first and last
raise parallel with the staircase.
Note! Measurement C is the upper edge of the
inner profile.
Make a line through mark A-A and D.
And make a line through mark C-C.
fig. 1
fig. 2
Place the upper rail on the wall
or columns and fasten it in
each end, on a wall installation
drill ø12-1 mm holes in the
wall for glue bolts. Minimum
90mm into the wall.
On an installation on columns
drill ø8,5mm holes and make a
M10 threads.
Be careful not to hit the rail.
Do the same with the support rail for the lower rail. Using a ø10mm drill bit for ø10 raw
plugs.
Handi-lift 7
2010 Page 6 Version 1.0
Note! For wall installation we recommend that you use M10 glue bolts for the upper rail
when mounted on a wall with the threaded rod minimum 90mm into the wall. And for the
lower rail, we minimum recommend ø10 raw plugs with M8x70mm screws.
For installation on columns we recommend that you fasten the rail with M10x25 8.8 bolts
with a nut on the inside of the column.
fig. 6
fig. 7
fig. 8
Make sure that the holes are nice and clean,
you might need to remove the rail to get all the
dust out.
Make sure that all measurements are correct.
fig. 9
Fill the holes with glue and insert the M10
threaded rod in the hole.
Handi-lift 7
2010 Page 7 Version 1.0
fig. 10
Install and tighten the support rail for the lower
rail
fig. 11
Install the aluminium rail on the support rail
using the M5x10mm countersunk screws.
fig. 12
After letting the glue set for a half-hour in 20
o
C
you can tighten the nuts on the glue bolts.
Or follow the instructions on the glue.
Handi-lift 7
2010 Page 8 Version 1.0
4Installing the lift unit
4 1 Place the lift unit on the rail:
Hand wind platform in it’s down position and remove the front cover from the lift unit.
Install the loose carrying arms
Handi-lift 7
2010 Page 9 Version 1.0
fig. 13
Please use tape to protect the rail.
Optional: To make the lift easier to handle you
can disassemble the platform, if necessary.
We recommend you install the lift with the
platform assembled.
Before inserting the lift to the rail make sure
that the upper limit switch is removed.
fig. 14
fig. 15
fig. 16
Insert the lift to the rail from the top.
Altri manuali per HANDI-LIFT 7
1
Indice
