Cambro MHWS18 Manuale utente

www.cambro.com

OWNER’S

MANUAL MOBILE HANDWASH STATION

This owner’s manual applies to the following

Mobile Handwash Station models:

MHWS18

Strainer

Weep Hole

Plug Kit

Paper Towel

Holder Kit

Soap

Dispenser Kit

2" Plug

Faucet Kit

Wheel

Axle Kit

Inlet Tube Kit

1 Cylinder Style Bumper

Pump Base Kit

Foot Pump Kit

Universal Drain

Valve Kits

Anchor Kit

Display Wrap

S21009

Strainer

H21018

Weep Hole

Plug Kit

S21007

2" Plug

H21012

Faucet Kit

S21010

Wheel

H21011

Axle Kit

47262

1 Cyclinder Style Bumper

H21014

Inlet Tube Kit

H21010

Anchor Kit

H21017

Soap

Dispenser Kit

H21015

Paper Towel

Holder Kit

I. Parts Checklist

H21016

Pump Base Kit

H19007(x1) H19008(x6)

Universal Drain Valve Kits

H21013

Foot Pump Kit

H21029

Display Wrap

Filling the Freshwater Tank

Fill the freshwater tank with a standard hose until water begins to overow

and/or use a nger to feel if the water has reached the max ll line. The ll

time from empty to full will take 2-3 minutes on average.

Operating the Unit:

Repeatedly depress foot pump to start and continue

the ow of fresh water from the faucet. When

nished, simply discontinue depressing foot pump.

Draining the Freshwater Tank:

To drain the freshwater tank, release the drain port on the side of the unit

opposite the wastewater drain valve.

Draining the Wastewater Tank:

To drain wastewater, a standard garden hose can be attached (optional) to

the threaded end of the wastewater valve on the side of the unit. By turning

the valve left a quarter turn, the wastewater tank will begin draining.

(Check local ordinance for wastewater disposal.)

Scan to watch

videos for lling

and draining

this unit.

II. Usage Guidelines

45˚

II. Usage Guidelines (continued)

Soap Dispensers

• Use access key to unlock and remove lid. If access key is lost, use

a flathead screwdriver to unlock soap dispenser lid.

• Press the clip to remove the dispenser from the mounting plate.

• Four AA batteries (not included) are installed on the underside

of the dispenser.

Unit weight (empty):

53.6 lbs. (24,3 kg).

Unit weight (full):

224.7 lbs. (101,9 kg).

Note

Soap dispenser can leak from the top during transport. Recommend to

transport with soap dispenser empty and/or do not tilt unit back more

than 45 degrees to prevent soap spillage.

III. Care and Maintenance

Cleaning and Water Maintenance:

• Use a mild soap to clean all surfaces and component parts.

Cleaning for Storage:

• Drain all water from the tanks.

• Flush tank with a solution of chlorine and water.

• Depress the foot pump to run the clorine solution through the lines.

• Drain all water from the tanks and while the drains are open, continue to

depress the foot pump to clear all of the liquids from the lines.

Short Term Storage:

• Keep the yellow plugs in. Plugs out will invite contamination.

Long Term Storage:

• Leave yellow plugs out to promote air circulation and complete drying of

the tanks. Remove plug at the weep hole near top handle and tilt unit flat

or even upside down to remove all excess water left in freshwater tank.

Removing the Wastewater Tank:

• Anchors on rear of unit must be unscrewed to remove the wastewater

tank (if needed). Do not over tighten the anchors when reinstalling the

wastewater tank.

Weep hole

Telephone 714 848 1555 Toll Free 800 854 7631 Customer Service 800 833 3003

Printed in USA 12/21

UMMHWS18

D092102

TO ORDER REPLACEMENT PARTS:

• Call Cambro Customer Service at 800 833 3003

• From International markets, call 714 848 1555

• Email customerservice@cambro.com

• Call your local Cambro Representative or Distributor

Please visit www.cambro.com/parts for a complete list of replacement parts for the MHWS18.

IV. Replacement Parts

Cambro warrants to the original buyer that if a product proves defective:

1. Within 1 year from the date of manufacture, Cambro will replace the product free of charge; or,.

2. After 1 year and up to 2 years from the date of manufacture, Cambro will grant a credit of 2/3 off replacement product; or,.

3. After 2 years and up to 3 years from the date of manufacture, Cambro will grant a credit of 1/3".

RETURN POLICY: Cambro Manufacturing products cannot be returned without prior written factory authorization (RMA). The restocking charge is 15% plus any costs

required to recondition the equipment. No returns accepted after 90 days from date of invoice. Electrical components returned are subject to inspection prior to credit