CAME VER KIT Manuale utente

CAME UNITED KINGDOM LTD

UNIT 3

ORCHARD PARK INDUSTRIAL ESTATE,

TOWN STREET, SANDIACRE,

NOTTINGHAM NG10 5BP

TEL: 0115 921 0430

FAX: 0115 921 0431

INTERNET - www.cameuk.com

E-MAIL - [email protected]

TECHNICAL

HELPLINE

0115 921 0430

VER KIT

Installation Instructions

Kit U 4281 includes:

1 x 001 V 600 Gearmotor built-in control panel and courtesy light

1 x 001 AF 43S Radio receiver 433.92 MHz

1 x 001 TOP-432SA Radio transmitter 433.92 MHz

1 x 001 TOP-A433N Radio antenna 433.92 MHz

Kit U 4281-B includes:

1 x 001 V 600 Gearmotor built-in control panel and courtesy light

1 x 001 AF 43S Radio receiver 433.92 MHz

1 x 001 TOP-432SA Radio transmitter 433.92 MHz

1 x 001 TOP-A433N Radio antenna 433.92 MHz

1 x 001 DOC-P Weatherproof pushbutton

1 x 001 V0675 Belt transmission guide

INTRODUCTION

These instructions will show you how to install a VER automatic traction system for

overhead and sectional doors.

1 - VER unit

2- incorporated control panel

Accessories

3- Radio receiver

4- Internal pushbutton

UNDER NO CIRCUMSTANCES SHOULD THIS EQUIPMENT BE OPERATED UNLESS FITTED TO A GATE.

FAILURE TO COMPLY WILL INVALIDATE THE GUARANTEE.

rotomraeG thgieW ylppuSrewoP noitprosbarotoM rewopxaM elcycytuD ecrofnoitcarT deepsegarevA

006V gK7,5 .c.aV032 xamA6 W031 %05 N005 nim/m6

007V gK9,5 xamA11 W062 N058

CHARACTERISTICS

GEAR MOTOR TECHNICAL CHARACTERISTICS

General description:

- Automatic traction system for overhead and sectional

doors;

- Designed and built entirely by CAME Cancelli automatici

S.p.A., in full compliance with current safety standards UNI

8612, and with an IP 40 protecting rating;

- Guaranteed for 12 months, unless tampered with by

unauthorized personnel.

Versions:

V600

Single-phase ratiomotor with mechanical end-stops and

built-in control board; 230V AC power with 50÷60Hz

frequency; 130W max. motor power and up to 500N in

traction power.

V700

Single-phase ratiomotor with mechanical end-stops and

built-in control board; 230V AC power with 50÷60Hz

frequency; 260W max. motor power and up to 850N in

traction power. Sliding guides:

V0671

Guide unit with chain L = 3,02 m; - for garage-type doors up

to 2,4 m tall with counterweights

- for garage-type doors up to 2,2 m tall with springs and

sectionals

V0672

Guide unit with chain L = 3,52 m;

- for garage-type doors up to 2,9 m tall with counterweights

- for garage-type doors up to 2,7 m tall with springs and

sectionals

V0673

Guide unit with chain L = 4,02 m;

- for garage-type doors up to 3,4 m tall with counterweights

- for garage-type doors up to 3,25 m tall with springs and

sectionals

V0675

Guide unit with belt L = 3,02 m;

- for garage-type doors up to 2,4 m tall with counterweights

- for garage-type doors up to 2,2 m tall with springs and

sectionals

V0676

Guide unit with belt L = 3,52 m;

- for garage-type doors up to 2,9 m tall with counterweights

- for garage-type doors up to 2,7 m tall with springs and

sectionals

V0677

Guide unit with belt L = 4,02 m;

- for garage-type doors up to 3,4 m tall with counterweights

- for garage-type doors up to 3,25 m tall with springs and

sectionals

Accessories

V201

Transmission adapter arm for garage-type doors with

counterweights (it substitutes the arm supplied), see pg. 7;

Optional accessories:

V0670

Emergency battery connection card with support for 2

batteries (12V-1,2Ah - ESCLUSE);

V121

Cable release device and transmission for connection to the

lock;

V122

Improved transmissionarm for sectional gates, see pg. 6;

Technical specifications:

- 24V DC gear motor; reduction gear unit housed in a die-

cast aluminium casing. The unit features an irreversible

reduction gear with worm screw and helicoidal.

Permanently lubricated with liquid grease.

- ABS automation container and cover with window for lamp

to illuminate the area. The unit is mounted on and

supported by the sliding guide.

- Built-in electric control panel.

- Microswitch end-stops;

- Galvanised cold-formed plate sliding guide; front

tensioning and fastening wall terminal; ABS back motor unit

support and connector terminal. The guide has a built-in

emergency release device and the transmission arm’s

hook; the guide has holes for possible connection of

additional brackets.

- Chain or belt sliding system.

Attention! to insure easy installation and conformance with

current safety, norms, we reccomend installation of CAME

safety and control accessories.

* For heights exceding 540 mm., it is necessary to use additional brackets or struts

Cable exit

400 212

140 18

540 max*

A - Sectional door

B - Spring-balanced overhead door

C - Overhead door ith counter eight balancing

EXAMPLES

APPLICATIONS

USE ONLY 250V FUSES

EXAMPLES OF APPLICATIONS

EXTERNAL DIMENSIONS

POWER SUPPLY PLUG & OUTLET

A - Sectional door

B - Spring-balanced overhead door

* For heights exceeding 540mm, it is necessary to use additional brackets or struts

C - Overhead door with counterweight

balancing or canopy door

M6x14

V122

Upper edge of door

30 ÷60 cm

Spring-bar

UNIT ASSEMBLY

PREARRANGEMENT OF TRANSMISSION GUIDE

- Fasten the bracket to the transmission guide’s front terminal with the nuts and bolts provided;

TRANSMISSION GUIDE FASTENING

- Fasten the transmission guide in the following manner:

a) for sectional doors, fasten the bracket directly to the wall over the spring-release coiling shaft using

adequate dowels and screws; if the distance between the coiling shaft and the gate’s upper ledge is

between 30 and 60 cm, apply the V122 arm (read the technical documentation provided with the

accessory);

V201

10 ÷20 mm

Fig. 1

b) for spring garage-type doors, fasten the bracket on the fixed frame with adequate screws or rivets.

c) for garage-type doors with counterweights or canopy doors, verify the maximum door sliding

point (fig.1) and consequently fasten the bracket on high with adequate screws or rivets.

N.B.: for garage-type doors with counterweights it is necessary to use the V201 adapter arm (read

the technical documentation provided with the accessory).

Ø7

M6x14

- Raise and set the guide horizontally to establish the distance from the ceiling; then fasten the angle

sections or fastening brackets provided (cutting off any excess part) to the guide’s back terminal.

N.B. the transmission guide has three ø7 holes for further fastening should it prove necessary to

reinforce the unit.

- Prepare the chase for electric wiring.

- Lift and fasten the transmission guide to the ceiling at right angles to the wall.

SLIDING LEVER FASTENING

- Centrally fix the sliding lever to the door’s upper crosspiece with the rivets provided;

- Mount the unlocking handle by screwing it to the preassembled unlocking unit’s revolving plug and

fasten it in the recommended position with the lock nut;

- Move the sliding runner and hook it to the transmission arm after removing the preset screw.

N.B.: if the adapter arm (V201) is used, hook the carriage to the sliding runner.

ø6,3x45

CAME

ø3,9x13

V121

GEAR MOTOR INSTALLATION

- Remove the automation container cover by unscrewing the ø3.9x13 screw;

- Fasten the container to the sliding guide’s back terminal in the desired position with the ø6.3x45

screws provided;

GEAR MOTOR UNLOCKING

- Turn the handle as illustrated; the rehooking of the release will take place automatically at the first

manoeuvre, re-setting the handle in the original position.

- If there is a V121 cable release device (read the technical documentation accompanying the

accessory for assembly instructions), turn the handle as illustrated to lock and the ratiomotor.

b) if in the clos re

TECHNICAL DESCRIPTION ZL55 CONTROL PANEL

The card is powered with a 230V (AC) power outlet and its

input is protected with a 1.6A line fuse. Control systems are

The total power consumption of 24V accessories (which are

protected by a 3.15A fuse) must not exceed 40W.

Fixed operating time of 80 sec.

Safety

Photocells can be connected to obtain:

- Re-opening during the closing cycle (2-C1), the photocells

on detecting an obstacle while closing the door, cause the

movement direction to be reversed until opening is

complete;

- Total stop (1-2), stop of the garage-type door with the

exclusion of the automatic closing cycle. To resume the

movement, use the pushbutton or the radio control;

- Amperometric safety device: see below, fig A and fig B.

Other functions

- Automatic closing. The automatic closing timer is

automatically activated at the end of the opening cycle. The

preset, adjustable automatic closing time is automatically

interrupted by the activation of any safety system, and is

deactivated after a STOP command or in case of power

failure;

- Obstacle detection. When the motor is stopped (gate is

closed, open or half-open after an emergency stop

command), the transmitter and the control pushbutton will

be deactivated if an obstacle is detected by one of the

safety devices (for example, the photocells);

- "Operator present" function. Gate operates only when the

pushbutton is held down (the radio remote control system is

deactivated);

- Pre-flashing. After an opening or closing command, the

flasher connected to the 10-E flashes for 5 seconds before

beginning the procedure;

- Type of command:

- «open-stop-close-stop»for pushbutton and radio

transmitter;

- «open-close»for pushbutton and radio transmitter;

- «open only»for pushbutton and radio transmitter.

Accessories connected

- Courtesy Light (24V-25W). A light that illuminates the

manoeuvring zone; after an opening command, the light

remains on for a fixed time of 2 minutes and 30 seconds.

Optional accessories

- Courtesy Light (24V-25W), connect it to terminal blocks W-

- Flashing signal light when gate is in motion (24V-25W

max.),

connect it to terminal blocks 10-E;

- V0670 board card for emergency battery.which is

automatically connected in case of power failure; battery is

recharged when line power is restored;

- AF radiofrequency board (see table on pg. 24) for remote

control.

Adjustments

- Trimmer TCA = adjustment automatic closing time;

- Trimmer SENS = adjustment sensitivity of amperometric

safety system.

Caution! Shut off the mains power and disconnect the

batteries if fitted before servicing the inside of the unit.

In the presence of an obstacle, the amperometric device:

a) completely stops the door during opening and subsequently closes it automatically (if activated);

b) if in the closure phase, the movement of the door is reversed.

N.B.: In situation (b), if an obstacle is detected three times, the door wing stops during aperture, and automatic closure is

disactivated. Use the keyboard or the radio transmitter to resume movement of the bar.

Altri manuali per VER KIT

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali CAME Porta

CAME

CAME Corsa Series Manuale utente

Manuali Porta popolari di altre marche

ENFORCER

ENFORCER Enforcer SK-990A Manuale utente

Electri-Chef

Electri-Chef TR18 Manuale del proprietario

BEA

BEA PBR45x Manuale utente

GE 19298 Manuale utente

Sterling Plumbing

Sterling Plumbing Frameless Bypass Shower Door SP5465-45 Manuale utente

GE 19214 Manuale utente

Ives

Ives 55 Manuale utente

Algoma Hardwoods

Algoma Hardwoods STC 39 Manuale utente

Ives

Ives Surface Bolt 43 Manuale utente

Therma-Tru

Therma-Tru Double-door Manuale utente

Erreka

Erreka PREMIS 200 Manuale utente

Ives

Ives Surface Bolt 144 Manuale utente

Lennox Hearth Products

Lennox Hearth Products MPB-35 Manuale utente

Ives

Ives Offset Top Pivot 7245F Manuale utente

KitchenAid

KitchenAid KBAU181V Manuale

Ives

Ives 670 Manuale utente

Ives

Ives Mortise Bolt S48 Manuale utente

American Standard

American Standard Acrylux 6000Y1.BE5 Manuale utente