CAME FA70230CB Manuale utente

Swing-gate operator

FA70230CB

INSTALLATION MANUAL

FA01335-EN

English

p. 3- Manual FA01335-EN - 04/2019 - © CAME S.p.A. - The contents of this manual may change, at any time, and without notice. - Original instructions

GENERAL PRECAUTIONS FOR INSTALLERS

Important safety instructions.

Follow all of these instructions. Improper installation can cause serious bodily harm.

Before continuing, also read the general precautions for users.

Use this product only for its specifically intended use. Any other use is hazardous. • The manufacturer can not be held

liable for any damage caused by improper, unreasonable, and erroneous use. • This manual's product is defined by the

Machinery Directive 2006/42/CE as partly-completed machinery. • Partly-completed machinery is an assembly that

almost constitutes a machine, but which, alone, cannot ensure a clearly defined application. • Partly-completed machinery

is only destined to be incorporated or assembled to other machinery or other partly-completed machinery or apparatuses

to build machinery that is regulated by the Machinery Directive 2006/42/EC. • The final installation must comply with

the Machinery Directive 2006/42/EC and the current European reference standards. • The manufacturer declines any

liability for using non-original products; which would result in warranty loss. • All operations indicated in this manual must

be carried out exclusively by skilled and qualified personnel and in full compliance with current regulations. • Laying of

cables, installation and testing must follow state-of-the-art procedures as dictated by applicable standards and laws. • All

the components (e.g. control panels, photocells, sensitive edges, etc.) necessary for the conformity of the final installation

in accordance with the Machinery Directive 2006/42/EC and with the reference harmonized technical standards are

identified in the CAME products general catalog or in the website www.came.com. • Make sure the mains power supply

is disconnected during all installation procedures. • Check that the temperature ranges given and those of the location

match. • If necessary, add suitable reinforcements to the anchoring points. If necessary, add suitable reinforcements

to the anchoring points. • Make sure that the operator, in the installation place, does not get wet by direct jets of water

(sprinklers, water cleaners, etc.). • Make sure you have set up a suitable dual pole cut off device along the power

supply that is compliant with the installation rules. It should completely cut off the power supply according to category III

surcharge conditions. • Demarcate properly the entire site to prevent unauthorized personnel to enter; especially children

and minors. • In case of manual handling, have one person for every 20 kg that need hoisting; for non manual handling

use proper hoisting equipment in safe conditions. • Use suitable protections to prevent any mechanical hazards due to

persons loitering within the operating range of the operator. • The electric cables must pass through special pipes, ducts

and cable glands in order to guarantee adequate protection against mechanical damage. • The electrical cables must not

touch any parts that may overheat during use (such as the motor and the transformer). • Before the installation, check that

the guided part is in good mechanical condition, and that it opens and closes correctly. • The product cannot automate

any guided part that includes a pedestrian gate, unless the latter can be enabled only when the pedestrian gate is secured.

• Make sure that people cannot be entrapped between the guided and fixed parts, when the guided part is set in motion.

• All fixed controls must be clearly visible after installation, in position that the guided part is directly visible, but far away

from moving parts. In the case of a maintained action command, this must be installed at a minimum height of 1.5 m from

the ground and must not be accessible to the public. • If not already present, apply a permanent tag, that describes how

to use the manual release mechanism, close to the mechanism. • Make sure that the operator has been properly adjusted

and that the safety and protection devices, and the manual release, are working properly. • Before turning over to the final

user, check that the system complies with the harmonized standards and the essential requisites of Machinery Directive

2006/42/CE. • Any residual risks must be indicated clearly with proper signage affixed in visible areas. All of which must

be explained to end users. • Fit, in plain sight, the machine's ID plate when the installation is complete. • If the power-

supply cable is damaged, it must be immediately replaced by the manufacturer or by an authorized technical assistance

center, or in any case, by qualified staff, to prevent any risk. • Keep this manual inside the technical folder along with

the manuals of all the other devices used for your automation system. • Remember to hand over to the end users all the

operating manuals of the products that make up the final machinery.

p. 4- Manual FA01335-EN - 04/2019 - © CAME S.p.A. - The contents of this manual may change, at any time, and without notice. - Original instructions

Main points of danger for people

Do not transit through during maneuvering.

Danger of entrapment.

Danger of hand entrapment.

Danger of foot entrapment.

DISMANTLING AND DISPOSAL

CAME S.p.A. employs an Environmental Management System at its premises. This system is certified and compliant with the UNI EN ISO 14001 regulation

standard to ensure that the environment is respected and safeguarded. Please continue safeguarding the environment. At CAME we consider it one of the

fundamentals of our operating and market strategies. Simply follow these brief disposal guidelines:

DISPOSING OF THE PACKAGING

The packaging materials (cardboard, plastic, and so on) should be disposed of as solid household waste, and simply separated from other waste for recycling.

Always make sure you comply with local laws before dismantling and disposing of the product.

DISPOSE OF RESPONSIBLY!

DISPOSING OF THE PRODUCT

Our products are made of various materials. Most of these (aluminium, plastic, iron, electrical cables) are classified as solid household waste. They can be recycled

by separating them before dumping at authorized city plants.

Whereas other components (control boards, batteries, transmitters, and so on) may contain hazardous pollutants.

These must therefore be disposed of by authorized, certified professional services.

Before disposing, it is always advisable to check with the specific laws that apply in your area.

DISPOSE OF RESPONSIBLY!

p. 5- Manual FA01335-EN - 04/2019 - © CAME S.p.A. - The contents of this manual may change, at any time, and without notice. - Original instructions

PRODUCT DATA AND INFORMATION

Legend

This symbol shows which parts to read carefully.

This symbol shows which parts describe safety issues.

This symbol shows which parts to tell users about.

The measurements, unless otherwise stated, are in millimeters.

Description

Irreversible operator with control board and jointed transmission-arm for swing gates with each leaf up to 2.3 m long.

Intended use

Ideal for applying in private homes and apartment buildings, on small-to-medium gate posts

Any installation and/or use other than that specified in this manual is forbidden.

Description of parts

Gearmotor

Cover

Control board

Release hatch

Brace for fastening to gate

Joint arm

Transmission arm

Transformer

Gearmotor

Rubber shim

Brace for fastening to the post

Limit-switch microswitch

p. 6- Manual FA01335-EN - 04/2019 - © CAME S.p.A. - The contents of this manual may change, at any time, and without notice. - Original instructions

Control board

All wiring connections are quick-fuse protected.

For the system to work properly, before fitting any plug-in card, you MUST CUT OFF THE MAIN POWER SUPPLY and remove any batteries.

Before working on the control panel, cut off the mains power supply and remove the batteries, if any.

Gearmotor terminals

Line fuse

Power supply terminal board

Terminal board for connecting the transformer

Control board fuse

Terminal board for connecting control and safety devices

programming status warning LED

Terminal board for connecting the antenna

Connector for plug-in radio frequency card (AF)

DIP for programming

ACT Trimmer: automatic closing time adjustment

Trimmer OP.TIME: adjustment of gearmotor working time

Trimmer DELAY 2M: adjustment of the M2 motor closing delay time

Button for programming

Accessories fuse

24V

TS 5C1 7 2 1 11 10 ES ES 12V 0CT

U V W X Y E L N

L2T L1T

1 32

1012 11

p. 7- Manual FA01335-EN - 04/2019 - © CAME S.p.A. - The contents of this manual may change, at any time, and without notice. - Original instructions

Dimensions

200 235

230

Limits to use

With irreversible gearmotors, an electric lock must be installed.

MODELS FA70230CB

Gate-leaf length (m) 2,3 2 1,5 1

Gate-leaf weight (Kg) 200 215 250 300

Technical data

MODELS FA70230CB

Power supply (V - 50/60 Hz) 230 AC

Motor power supply (V) 230 AC

Board power supply (V) 24 AC

Stand-by consumption (W) 5,5

Power (W) 160

Condenser (µF) 10

Current draw (mA) 1,4

Working temperature (°C) -20 ÷ +55

Torque (Nm) 180

Opening time at 90° (s) 15

Work time (s) 14 ÷ 120

Duty cycle (%) 30

Motor thermal protection (°C) 150

Protection rating (IP) 54

Insulation class I

Reduction ratio (i) 735

Fuse table

MODELS FA70230CB

Line fuse 5 A F

Control-board fuse 315 mA F

Accessories fuse 3.15 A F

p. 8- Manual FA01335-EN - 04/2019 - © CAME S.p.A. - The contents of this manual may change, at any time, and without notice. - Original instructions

Cable types and minimum thicknesses

Cable length (m) up to 20 from 20 to 30

230 V AC Power supply 3G x 1.5 mm2 3G x 2.5 mm2

Power supply to motor 230 V AC 3G x 1.5 mm2 3G x 2.5 mm2

TX Photocells 2 x 0.5 mm2 2 x 0.5 mm2

RX photocells 4 x 0.5 mm2 4 x 0.5 mm2

12 V DC electric lock 2 x 1 mm2 2 x 1.5 mm2

Command and control devices * no. x 0.5 mm2 * no. x 0.5 mm2

*no. = see product mounting instructions - Warning: the cable section is merely indicative as it depends on the motor power and cable length.

When operating at 230 V and outdoors, use H05RN-F-type cables that are 60245 IEC 57 (IEC) compliant; whereas indoors, use H05VV-F-type cables that

are 60227 IEC 53 (IEC) compliant. For power supplies up to 48 V, you can use FROR 20-22 II-type cables that comply with EN 50267-2-1 (CEI).

To connect the antenna, use the RG58 (we suggest up to 10 m).

If cable lengths differ from those specified in the table, establish the cable sections depending on the actual power draw of the connected devices and

according to the provisions of regulation CEI EN 60204-1.

For multiple, sequential loads along the same line, the dimensions on the table need to be recalculated according to the actual power draw and

distances. For connecting products that are not contemplated in this manual, see the literature accompanying said products

p. 9- Manual FA01335-EN - 04/2019 - © CAME S.p.A. - The contents of this manual may change, at any time, and without notice. - Original instructions

INSTALLATION

The following illustrations are just examples, as the space available for fitting the operator and accessories varies depending on the area where it is

installed.

The drawings refer to the left-side gearmotor.

Preliminary operations

Set up the junction boxes and corrugated tubes you will need to make connections coming from the junction pit.

An operator (FA70230CB) and a gearmotor (FA70230) must be installed on two-leaf gates .

FA70230CB must be installed on the leaf that must start the opening maneuver first.

FA70230 must be installed on the leaf that must start the opening maneuver subsequently.

The number of tubes depends on the type of system and the accessories that are going to be fit.

Setting up the gearmotor

Carefully remove the gearmotor cover.

p. 10 - Manual FA01335-EN - 04/2019 - © CAME S.p.A. - The contents of this manual may change, at any time, and without notice. - Original instructions

Establishing the brackets fastening points