Campbell Hausfeld WS090001AV Istruzioni per l'installazione e il funzionamento

Additional Model Instructions Model WS090001AV

Addendum to Owner’s Manual

IN170138AV 2/99

BUILT TO LAST

Shielded Metal

Arc Welder

Description

Thank you for purchasing the

Campbell Hausfeld 70 amp Arc Welder,

Model #WS090001AV. This instruction

sheet is to be used in conjunction with

the standard owner’s manual included

with the welder (IN198904AV). Please

refer to this sheet for WS090001AV

assembly instructions.

Please read all

warning instructions in

the owner’s manual

before operating.

Components

The WS090001 comes with the

following additional equipment:

• Automatic amperage adjustment -

low position for 1/16” rods and

high position for 5/64” rods--for

ease of use.

• Cable storage clips (shown in

Handle Assembly) for safer storage

of welding cables.

Handle Assembly

1. Align the end holes on the handle

with the holes on top of the welder,

then secure with screws (Figure 1).

!NOTICE

MANUAL

2. Insert cable clips by pressing inward

on sides of clip and pushing into

the slots on front of handle as

shown in Figure 2. Repeat for

opposite side of handle.

Electrode Holder Assembly

(Refer to Figure 3)

1. Remove insulation handle from the

holder body by pulling the two

pieces apart.

2. Slide the other weld cable through

the handle.

3. Loosen the wire clamping screw

and slide the bare cord wire under

the clamp block. Tighten the

clamping screw and make sure the

wire is secure.

4. Slide the handle over the electrode

holder body and press to stop.

Make sure the handle is secure and

there is no exposed metal on the

holder.

Figure 3 - Electrode Holder

Figure 2

Figure 1

For parts, product & service information

visit www.campbellhausfeld.com

Ref. Part Number

No. Description for WS090001 Qty

1Electrode holder assembly - cord not included (includes ref. # 2-7) WC200000AV 1

2 Electrode holder handle - cord not included WC200001AV 1

3 Electrode holder body WC200002AV 1

4 Insulation cap WC200003AV 1

5 #10-24 x .5” machine screw * 1

6 #10-24 x 7/16” square nut * 1

7 Work clamp WC100300AV 1

8 Handle WC301300AV 1

9 #8-36 x 3/4” pan head screw * 2

10 Safety decal (right) DK404300AV 1

11 Safety decal (left) DK404400AV 1

12 Welding cable 6 AWG (6 ft) * 2

13 Power cord 14-3 AWG (6 ft) Type SJT WC000100AJ 1

14 High/off/low thermal indicator WC401000AV 1

15 Strain relief WC102000AV 2

16 Cord storage clip WC301301AV 2

* Standard hardware item, available at local hardware or welder supply store

Additional Model Instructions WS090001

For Replacement Parts, call 1-800-746-5641

Address parts correspondence to:

The Campbell Group

Attn: Parts Department

100 Production Drive

Harrison, Ohio 45030

Please provide following information:

- Model number

- Serial number (if any)

- Part description and number as

shown in parts list

Altri manuali Campbell Hausfeld Sistema di saldatura

Campbell Hausfeld

Campbell Hausfeld WS2800 Istruzioni per l’uso

Campbell Hausfeld

Campbell Hausfeld WF2050 Istruzioni per l’uso

Campbell Hausfeld

Campbell Hausfeld WS0970 Manuale di servizio

Campbell Hausfeld

Campbell Hausfeld IN972101AV Manuale di servizio

Campbell Hausfeld

Campbell Hausfeld DW3130 Manuale di servizio

Campbell Hausfeld

Campbell Hausfeld WG4000 Manuale di servizio

Campbell Hausfeld

Campbell Hausfeld ARCITECH WS2100 Manuale di servizio

Campbell Hausfeld

Campbell Hausfeld WS0970 Manuale di servizio

Campbell Hausfeld

Campbell Hausfeld WS0900 Manuale di servizio

Campbell Hausfeld

Campbell Hausfeld WG204498AJ Manuale utente

Campbell Hausfeld

Campbell Hausfeld WT2531 Manuale utente

Campbell Hausfeld

Campbell Hausfeld WF1800 Istruzioni per l’uso

Campbell Hausfeld

Campbell Hausfeld WK250000AV Manuale di servizio

Campbell Hausfeld

Campbell Hausfeld WG3060 Istruzioni per l’uso

Campbell Hausfeld

Campbell Hausfeld WG3000 Istruzioni per l’uso

Campbell Hausfeld

Campbell Hausfeld WF2034 Istruzioni per l’uso

Campbell Hausfeld

Campbell Hausfeld WG3020 Istruzioni per l’uso

Campbell Hausfeld

Campbell Hausfeld WT6000 Manuale utente

Campbell Hausfeld

Campbell Hausfeld WT5000 Manuale

Campbell Hausfeld

Campbell Hausfeld WG2020 Manuale di servizio

Campbell Hausfeld

Campbell Hausfeld WG2060 Manuale di servizio

Campbell Hausfeld

Campbell Hausfeld Welder/Generator Manuale utente

Campbell Hausfeld

Campbell Hausfeld WT2531 Manuale utente

Campbell Hausfeld

Campbell Hausfeld WS0970 Manuale di servizio

Manuali Sistema di saldatura popolari di altre marche

Berner

Berner PLASMACUT 54 Manuale utente

Pro Spot

Pro Spot PR-155 Manuale utente

Forney

Forney 210 Manuale utente

Thermal Arc

Thermal Arc 400S Manuale utente

Lincoln Electric

Lincoln Electric HANDYMIG 170I Manuale utente

GYS

GYS PROTIG 201 AC/DC Manuale utente

TAFA

TAFA 30*8B35 Manuale utente

Lincoln Electric

Lincoln Electric INVERTEC V350-PRO CE Manuale utente

ESAB

ESAB Buddy Arc 145 Manuale utente

CIGWELD

CIGWELD 636804 Guida rapida

Red-D-Arc

Red-D-Arc DC-400 Manuale utente

Hobart Welding Products

Hobart Welding Products Spool Gun DP 3035-10 Manuale utente

Elettro

Elettro HI-MIG 3000 SYNERGIC Manuale utente

WIA

WIA Weldmatic 270 CP132-2 Manuale utente

Sonics

Sonics H520T Manuale utente

Miller

Miller Big Blue 400D Manuale utente

NewArc

NewArc RT2000 Guida rapida

Hypertherm

Hypertherm powermax1000 Manuale utente