Cannon Security Products Wall Safe Manuale utente
TV Mount Wall Safe
OWNERS MANUAL
Rev (9/13)
1
Index
Safe Information……………………………………………………………...……………Pg. 2
Warning
Standard Features
Installation/Mounting…………………………………………………...………………...Pg. 3
Set Up………...……………………………………………………...……………………...Pg. 4
Opening the Door with the Key
Installing the Batteries
Opening the Door with the Keypad
Lock Out (Wrong Try Penalty)
Changing the Access Codes
Locking/Closing the Door
Warranty………………………………………………………...…………………………..Pg. 6
Unit Information/Record
DO NOT LOCK THIS IN YOUR SAFE
Important: Taking the time to fill out the information below and stapling a copy of your receipt
to this manual will help expedite any service needs.
(888) 220-1116
Purchased From:
Purchased Date:
Serial Number:
Key Number:
2
Safe Information
Warning
Install safe before using.
After installing, change the default factory codes.
Don’t put emergency key(s) or manual in the safe.
Standard Features
TV Mount for TV’s holds up to 65 inches and 80lbs. Maximum VESA of 400 x 400.
Hidden storage compartment.
Quick drop down access door.
Two user access codes.
Lock out after ten (10) wrong entries for three (3) minutes.
Electronic or Mechanical Access.
LED Lighted Compartment.
3
Included Hardware
4
Mounting the Wall Safe
The Wall Safe can be mounted into a standard residential wall with a depth of at least 7.88
inches and a wall area of at least 22.84 inches (horizontal position) X 26.78 inches (vertical
position).
Make a hole in the wall that is approximately 14.37 inches X 14.37 inches.
Carefully place the safe into the wall. Don’t forcefully insert, the unit should slide into the
opening easily.
Note: There should be a .25 inch gap between the safe and wall.
Open the door and locate the 4 mounting tabs (2 on each side of walls). Mark holes for
pre-drilling.
Remove the safe and pre-drill holes at the marked locations.
Reinsert safe into the wall and secure it with four (4) wood screws (A) and four (4) 3/8”
flat washer (L).
5
Installing the TV Mount Arm
The TV Wall Safe requires the TV arm to be attached after installation. Locate the TV arm, Shaft (K), and
two (2) M8x16 Button Head Socket Screws (J) in preparation of the installation.
Insert the end of the TV arm into the mounting bracket on the safe (as pictured below).
While holding the TV arm in the mounting bracket on the safe, insert the Shaft (K) and use the
two (2) M8x16 Button Head Socket Screws (J) to secure the TV arm to the wall safe. Use caution
not to over tighten and/or strip the heads of the screws.
6
Fitting the Brackets to the TV
Installation of the TV brackets may require the use of Plastic Sleeves (B) if the back of the TV is not flat
or the mounting holes are recessed. Locate the TV brackets, M6 Flat Washers (M), Scews (D, E, F, G, H,
or I), and Plastic Sleeves (B).
Choosing the scew length and diameter.
oHand thread screws into the threaded inserts on the back of the TV to determine the
correct screw diameter and lenghth. Important: The incorrect screws can cause
potential damage to person or property. See image below to the left:
Line up the holes on the TV brackets to the mounting holes on the back of the TV and assure the
TV brackets are level, see image above to the right. Important: If the TV brackets do not lay flat
against the TV or the mounting holes are recessed, use the four (4) Plastic Sleeves (B) between
the TV brackets and TV.
After lining up the holes, install the needed hardware as pictured above. Important: Do not
over tighten the screws.
7
Mounting the TV to the Wall Safe
CAUTION: YOU WILL NEED INSTALLATION ASSISTANCE WITH THESE
STEPS.
Lift TV onto bracket as shown in Diagram 1, making sure it is secure to the top lip of the bracket.
Center TV onto the bracket as shown in Diagram 2.
Tighten set screw to bottom of bracket as show in Diagram 3.
Diagram 1 Diagram 2
Diagram 3
8
Setting Up the Wall Safe
Opening the Door with the Key
In an emergency or electronic failure, the safe can be accessed by using a backup key. The key
slot is hidden behind the logo name plate on the front of the safe.
Use an allen wrench to unscrew the logo plate.
Insert the key into the lock and turn counter-clockwise to open.
Installing/Replacing the Batteries
With the door in the open position, locate the black battery compartment cover inside the safe
on the roof/top.
Remove the black battery compartment cover by pressing the tab to the left and pulling
down.
The battery tray will drop down. Install four (4) new AA Alkaline Batteries and reinsert the
battery tray with ‘INSERT INWARD’ facing into the compartment.
Reinstall the black battery compartment cover.
9
Opening the Door with the Keypad
If opening for the first time, the default access codes are ‘1234’ and ‘123456’. Batteries must
be installed to work.
Enter the current one (1) to eight (8) digit code followed by the (#) button.
If the code is correct, the door will open automatically.
Note:
If the (*) button is pushed when entering the code, the process starts over.
If there are five (5) beeps with yellow LED flashes the code entered is not recognized as
the current code.
Lock Out (Wrong Try Penalty)
After ten (10) wrong entries the lock will go into lock out for three (3) minutes. Do not press any
buttons during the lockout period, it will restart the three (3) minute lock period.
Changing the Access Codes
To program your access codes, follow the instructions below:
Setting Main Code Number:
oOpen the door.
oPress the ‘RESET’ button in the upper right corner of the inside of safe. System
will beep twice and yellow LED lights up.
oInput the new one (1) to eight (8) digit code followed by the (*) button.
oYour new code is now recorded.
Setting secondary code number:
oOpen the door.
oPress the ‘0’ button twice (0-0) on the keypad.
oPress the ‘RESET’ button in the upper right corner of the inside of safe. System
will beep twice and yellow LED lights up.
oInput the new one (1) to eight (8) digit code followed by the (*) button.
oYour new code is now recorded.
Note: When entering the new code, the (*) button is not active.
Locking/Closing the Door
Slowly lift up on the bottom of the door.
Push upwards firmly until door lock engages.
Indice
