Caple AS610BK Manuale utente

Instruction manual for wall chimney hoods

Model codes: AS610BK / AS910BK

Contact Caple on 0844 800 3830 or for spare parts www.4caple.co.uk

1. For ease of installation, the light assembly should be fitted using a magnetic

screwdriver before the hood is installed on the wall.

2. The plastic cover is to protect the light assembly in transit. Once the light is

fitted to the hood, the plastic cover is easily removed by slackening the screws

and pulling the cover off.

4. For ease of installation, the light assembly should be fitted using a magnetic

screwdriver before the hood is installed on the wall.

5. The plastic cover is to protect the light assembly in transit. Once the light is

fitted to the hood, the plastic cover is easily removed by slackening the screws

and pulling the cover off.

Installing the Ductwork

1. Plan where the ductwork will run between the hood and the outside. The

hoods exhaust vertically but can be ducted to the rear behind the chimney

duct through an outside wall or vertically up through the ceiling to the

roof. A short straight duct run will produce the most air flow. Length and

elbows will reduce the efficiency of the blower.

2. Install a roof or wall cap. Connect a 6 round metal duct to the cap and

work backwards toward the hood. Ensure joints are completely sealed

with duct tape.

Fixing to the Wall

1. Before mounting the hood, plug in and test all functions for correct operation.

2. Remove the filters from the bottom of the hood to pre vent damage during the installation.

3. With assistance, hold the hood temporary in position ensuring the bottom is above the minimum clearance for

the cooking surface. Mark on the wall the holes for the two mounting screws.

4. Drill the holes and install the mounting bracket (1) . Use the appropriate screws and screw anchors for your

wall type (e.g. reinforced concrete, drywall, etc.). If necessary, prepare back wall with cross framing for secure

installation.

5. Mount the hood onto the bracket (2).

Connect a 6 aluminum duct tube (not included) to the exhaust piece using duct tape on all seals. (C)

7.

to roof cap

to wall cap

hood

decorative

chimney duct

38

39

40

Mounting bracket

Hook

1

2

mushroom tapping screw

3

6. Install two mushroom tapping screw into the wall.

Installing Guideline

Wall Mounted-Duct-out

1200~1700mm

650~700mm

Note:The above installation guideline for references only , please contact your local dealer

for a installation service.

Fixing the Decorative Chimney

Flu

1

2

3

.

.

.

Carefully losen but do not separate the telescopic chim ney duct pieces.

Arrange the electrical power supply within the dimen sions of the

decorative chimney duct.

Adjust the width of the support bracket to match the upper duct. Fix it

to the ceiling using the screws (B) so that it is centered in line with your

hood and at a distance from the ceiling indicated.

C

1. Separate lamp cover and left bracket by unscrewing.

2. Install right bracket to the cooker hood, then tighten the screws.

3. Connect two cables.

4. Re-Install left bracket and tighten the screws.

Questo manuale è adatto per i seguenti modelli

1

Indice

Altri manuali Caple Cappa di ventilazione

Manuali Cappa di ventilazione popolari di altre marche

emmeti

emmeti RECUPA MED A-140 Guida

Nibe

Nibe F135 Manuale utente

Kuppersberg

Kuppersberg INTRO 60 Istruzioni di installazione e manutenzione

Zephyr

Zephyr Spruce AK9834BS Guida all'installazione

Hisense

Hisense MH6INBG Manuale utente

Miele

Miele DA 1255 Manuale utente

Broan

Broan 46000 Manuale utente

GE

GE Profile PV977 Istruzioni originali

FALMEC

FALMEC FFRIA24W5FS Manuale utente

Whirlpool

Whirlpool RH2600XL-1 SERIES Manuale utente

Küppersbusch

Küppersbusch DX ISLA Manuale utente

ETNA

ETNA AV360RVS Manuale utente

JUNO

JUNO JDF603E6 Manuale utente

Miele

Miele DA 6708 D Manuale utente

Tricity Bendix

Tricity Bendix LE 150 Manuale

AEG

AEG X68163BV1 Manuale utente

AEG

AEG 125 D Manuale utente

Smeg

Smeg KSEV97X Manuale utente