Car Solutions Video Interface Manuale utente
Warning
When installing the main unit, do not remove or alter existing
vehicle fasteners, including nuts, bolts, screw, clips, and fittings.
Never detach, move or alter existing vehicle wiring, including
electrical grounds and straps. Alteration of existing vehicle
components may make vehicle unsafe to operate. Should be
no any electronic devices or magnetic pole around installation
place.
Air bags are vital part of a safety system. Never install main unit
in a way which will alter air bag wiring or interfere with air bag
deployment. Air bags must function properly in the event of an
accident.
Before installing, check the location of pipe, tank, electrical
cables and others.
ead and follow the instruction manual.
Wiring location must not interfere driving, get in or out from car.
Use electrical tape to insulate the ends of all wires, even if they
are not used. Proper insulation prevents arcs, shocks and fires.
When installation is complete, test all vehicle electrical systems
to ensure they operate correctly, including lights, horn, brake
lights, and emergency flashers.
According to our sales policy, any problems caused by user’s
mistake, careless can not be guaranteed.
Caution
All steps of installation should be done by well-trained specialist.
During installation ignition key should be taken off and after all
installation finish connect power cable with interface for the last step.
Do not install the main unit in places where it ma be exposed to dew
condensation (around the air conditioning hose, etc), or in locations
where it may come in contact with water, high levels of moisture, dust
or oily smoke
Install wiring in a manner in which cables will not come in contact with
metal parts. The wiring may be damaged by contact with metal parts,
resulting in fire and shocks. Avoid all contact with hot surfaces when
wiring the main unit. High temperatures may damage wiring, causing
shorts, arcing and fires.
Kindly check all parts are in the box, when receiving the product, if
anything missing, inform to the supplier or manufacturer.
Warning / Caution
www.car-solutions.com
Car-Solutions.com
Table of Contents
1. Specifications
1.1 Main Specifications
1.2 Functions
1.3 System Diagram
1.4 Components
1.5 Exterior
2. Installation
2.1 Installation Diagram
2.2 Installation
2.3 CAN wire Installation
3. Settings
3.1 DIP Switch
3.2 emote Control
3.3.1 Parking guidelines/3D PDC
3.3.2 PIP(picture in picture)
3.3.3 Factory Mode -IMAGE, PA K
3.3.4 Factory Mode – UTIL 1
3.3.5 Factory Mode – UTIL 2
3.3.6 Factory Mode – INFO
3.3.7 Factory Mode – OSD Analog GB
3.3.8 Factory Mode – OSD Video
4. Trouble Shooting
1
2
3
4
5
6
7
8
9
10
11
12
13
14
16
19
20
21
22
www.car-solutions.com
Car-Solutions.com
1. Specifications
-1-
1.1 Main Specifications
1. Car Compatibility
Volvo S 0, XC 0 2015 year
2. Components
Interface* 1EA
3. MULTIMEDIA INTE FACE input specification
3 * A/V input (video external input)
1 * CVBS( ear Camera) input
2 * Analog GB input (Navigation system, HDMI)
1 * LCD input (Car system input)
4. MULTIMEDIA INTE FACE output specification
1 * LCD output
5. Power specification
Input power : 8VDC ~ 18VDC
Consumed power : 5WATT
www.car-solutions.com
Car-Solutions.com
1. Dynamic PAS(Parking assistance system)+3D PDC(Parking
distance control)
- moving parking line according movement of steering
wheel
- Front / ear car distance sensor display in external mode
2. Support PIP display – showing sources at the same time
(Picture in Picture)
1. Specifications
1.2 Functions
-2-
www.car-solutions.com
Car-Solutions.com
1. Specifications
-3-
1.3 System Diagram
DIS LAY
A/V 1
NAVIGATION Input
(Analog RGB)
CVBS
(Rear camera)
Car Screen Input
(CAR MAIN BOARD)
A/V 2
A/V 3
VIDEO
CI CUIT
VIDEO MUX
MCU
ower Input
(+8VDC ~ +18VDC)
POWE
CI CUIT
Dip S/W
A/V OUT HEADREST
MONITOR
Remote control Switch for source toggle
OEM Button (Can Signal)
Car Installation
OEM LCD
Rear Camera ower
(+12 VDC)
HDMI Input
(Analog RGB-2)
www.car-solutions.com
Car-Solutions.com
1.4 Components
1. Specifications
-4-
AV cable * 1ea
TOUCH OUT cable * 1ea EA CAME A
POWE cable * 1ea
(HA ETC0002)
(HAVCAB0002)
MODE cable * 1ea
(HA ETC0001)
GB_IN cable(9P) * 1ea
(H GBCA0013)
I cable * 1ea
(HI CAB0002)
(HTOUCH0004)
7P POWE cable * 1ea
(HTOUCH0068)
LVDS IN/OUT cable * 1ea
(HLCDCA0028)
TOUCH IN cable * 1ea
(HTOUCH0009)
www.car-solutions.com
Car-Solutions.com
① ⑥ ⑦
⑨
⑩⑪
② ③ ④ ⑤
⑫
-5-
Dimension
Width 164mm
Length 91mm
Height 19mm
①MODE
②I
③POWE
④TOUCH OUT
⑤EA
⑥GB-IN(HDMI)
⑦GB-IN(NAVI)
⑧AV/INOUT
⑨LVDS IN
⑪TEST
⑩T/S-IN
⑫LED
1. Specifications
1.5 Exterior
⑧
⑬
⑬ DIP S/W
www.car-solutions.com
Car-Solutions.com
2. Installation
-6-
2.1 Installation Diagram
※ Pl ease connect ACC cabl e t o B+ cabl e
R
E
A
R
(9V O
U
T)
G
N
D
AV1
AV2
AV3
EA C
Audio L
Audio
AV/OUTVideo
EA -C
N.C
N.C
ACC
CAN-L
CAN-H
GND
COMMAND
MONITOR
Supplied LCD IN
Supplied LCD OUT
OEM LCD Cable
www.car-solutions.com
Car-Solutions.com
3. Settings
-9-
3.1 DI Switch
PI N
PI N Funct i on
Funct i on
Dip S/W Selection
Dip S/W Selection
1Displaying GB input ON : RGB mode ski p
OFF : RGB mode di spl ay
2Displaying A/V 1 ON : A/V 1 mode ski p
OFF : A/V1 mode di spl ay
3Displaying A/V 2 ON : A/V 2 mode ski p
OFF : A/V2 mode di spl ay
4Displaying A/V 3 ON : A/V 3 mode ski p
OFF : A/V3 mode di spl ay
5, Sel ect Car model 5-ON, -OFF : V40
5, -OFF : S 0, XC 0
7Setup of rear camera use ON : CVBS4
OFF : MAI N
8no use
※Example DIP S/W usage
- Use input mode : A/V2, A/V3
- Use original navigation
- External rear camera
▷DIP S/W : 1 ON (hide INPUT MODE)
▷DIP S/W : 2,3 OFF (A/V1,2 display)
▷DIP S/W : 4 OFF (A/V3 display)
▷DIP S/W : 5 ON/OFF
▷DIP S/W : 6 ON/OFF
▷DIP S/W : 7 ON (display external rear cam)
▷DIP S/W : 8 OFF
※ON : DOWN / OFF : U
Default: #8 OFF
www.car-solutions.com
Car-Solutions.com
Altri manuali per Video Interface
1
Indice
