Carrier UPC Open Guida rapida alla configurazione

A member of the United Technologies Corporation family · Stock symbol UTX · Catalog No. 11-808-468-01 · 6/1/2017

Verify that you have the most current version of this document from www.hvacpartners.com or your local Carrier

office.

Important changes are listed in Document revision history at the end of this document.

Corporation. All other trademarks are the property of their respective owners.

 
 
 
Contents 
UPC Open overview and specifications...................................................................................................................... 1 
What is the UPC Open?........................................................................................................................................1 
Specifications ........................................................................................................................................................2 
Safety considerations...........................................................................................................................................3 
Installing the UPC Open .............................................................................................................................................. 4 
Mounting the UPC Open ......................................................................................................................................4 
Wiring the UPC Open for power..........................................................................................................................4 
To wire for power................................................................................................................................... 5 
Addressing the UPC Open....................................................................................................................................5 
Wiring for communications.................................................................................................................................5 
Wiring specifications for BACnet MS/TP and ARC156........................................................................ 6 
To wire the controller to the BACnet network 
...................................................................................... 6 
Wiring the UPC Open to the CCN network ........................................................................................................7 
Wiring specifications for CCN ............................................................................................................... 7 
To wire the CCN equipment to the UPC Open...................................................................................... 8 
Wiring devices to the UPC Open's Rnet port ....................................................................................................8 
Rnet wiring specifications..................................................................................................................... 8 
ZS Sensor overview ............................................................................................................................... 9 
SPT sensor overview ............................................................................................................................. 9 
To wire the ZS or SPT sensor to the UPC Open .................................................................................10 
Wireless sensor overview ...................................................................................................................10 
To install the Wireless Adapter for wireless sensors.........................................................................11 
To wire an Equipment Touch to the UPC Open..................................................................................12 
Start-up.......................................................................................................................................................................14 
Select or create a custom control program and graphic for the UPC Open............................................. 14 
To install the UPC Open into an i-Vu® Control System................................................................................ 15 
Configure the UPC Open's properties ............................................................................................................. 16 
Troubleshooting .........................................................................................................................................................18 
LED's .................................................................................................................................................................... 18 
To get the serial number .................................................................................................................................. 19 
To restore defaults............................................................................................................................................. 20 
To replace the UPC Open's battery ................................................................................................................. 20 
Compliance ................................................................................................................................................................21 
FCC Compliance................................................................................................................................................. 21 
CE Compliance ................................................................................................................................................... 21 
BACnet Compliance........................................................................................................................................... 21 
Appendix: Single Point Linkage and Device Address Binding ...............................................................................22 
Single Point Linkage ......................................................................................................................................... 22 
Device Address Binding .................................................................................................................................... 23 
Document revision history ........................................................................................................................................24 
 

What is the UPC Open?

The UPC Open (Universal Protocol Converter) is a general purpose protocol converter. The UPC Open can convert

proprietary equipment data into open protocol data, enabling a stand-alone, single piece of equipment to reside

on a BACnet network, where it can be monitored or controlled by a Building Automation System (BAS).

NOTE A future release of the UPC Open will support installation on a Modbus, N2, or LonWorks network.

UPC Open overview and specifications

Specifications

Driver

drv_upcopen_x-xxx-xxx

Maximum number of control

programs

Maximum number of

BACnet objects*

1050

* Depends on available

memory

Total available memory for application is 551244 bytes.

Obtain available memory information by viewing a Module Status report after the

control program is loaded.

Power

24 Vac ±10%, 50–60 Hz

10 VA power consumption (16 VA with BACview® device attached)

26 Vdc (25 V min, 30 V max)

Single Class 2 source only, 100 VA or less

We highly recommend using a dedicated transformer to power the UPC Open.

BAS port (Port 1a)

3-pin port supports EIA-485 2-wire communications.

Protocols supported (DIP switch selectable):

○BACnet MS/TP (m)

○BACnet ARC156

○Modbus (RTU) (future)

○Johnson N2 (future)

○LonWorks (future)

This port must be configured as a BAS port.

CCN port (Port 2)

5-pin port supports EIA-485 3-wire connection to a single Carrier CCN controller

LON-OC port

14-pin communication port supports the LonWorks Option Card (future)

Rnet port

The UPC Open only supports ZS sensors, Equipment Touch, and wireless sensors

with the 6.04.xxx or later driver.

Supports:

•Up to 10 ZS sensors (5 per control program)

•One Wireless Adapter that communicates with up to 15 wireless sensors

•One Equipment Touch

•Up to 4 SPT Standard sensors and one SPT Plus, SPT Pro, or SPT Pro-F

sensor.

NOTE ZS sensors, a Wireless Adapter, and an Equipment Touch can share the

Rnet, but not SPT sensors.

Local Access port

For system start-up and controller troubleshooting using Field Assistant or

Equipment Touch

Battery

10-year Lithium CR2032 battery retains the following data for a maximum of

10,000 hours during power outages: control programs, editable properties,

schedules, and trends.

Protection

Built-in surge and transient protection circuitry - internal solid state Polyswitches

on the incoming power and network connections.

Real time clock

Battery-backed real time clock keeps track of time in the event of a power failure

UPC Open overview and specifications

Status indicators

LED's indicate status of communications, running, errors, and power.

Environmental operating

range

-22 to 150°F (-30 to 66°C), 0 to 90% relative humidity, non-condensing

Storage temperature range

-24 to 140°F (-30 to 60°C), 0 to 90% relative humidity, non-condensing

Physical

Rugged GE C2950HF Cycoloy plastic

Overall dimensions

5-3/16 in. (13.2 cm)

4-1/8 in. (10.5 cm)

Mounting hole dimensions

4-7/8 in. (12.4 cm)

2-1/20 in. (5.2 cm)

3/16 in. (.5 cm)

Panel depth

2 in. (5.1 cm)

Weight

.44 lbs (.2 kg)

BACnet support

Conforms to the BACnet Advanced Application Controller (B-AAC) Standard Device

Profile as defined in ANSI/ASHRAE Standard 135-2012 (BACnet) Annex L,

Protocol Revision 9

Listed by

UL-916, (Canadian Std C22.2 No. 205-M1983), CE, FCC Part 15-Subpart B-Class

Safety considerations

WARNING Disconnect electrical power to the UPC Open before wiring it. Failure to follow this warning could

cause electrical shock, personal injury, or damage to the controller.

Installing the UPC Open

1 Mount the controller (page 4).

2 Wire the controller for power (page 4).

3 Set the controller's address (page 5).

4 Wire the controller to the BACnet MS/TP or BACnet ARC156 network (page 5).

5 Wire the controller to the CCN network (page 5).

6 Wire devices to the controller's Rnet port (page 8).

Mounting the UPC Open

WARNING

When you handle the UPC Open:

•Do not contaminate the printed circuit board with fingerprints, moisture, or any foreign material.

•Do not touch components or leads.

•Handle the board by its edges.

•Isolate from high voltage or electrostatic discharge.

•Ensure that you are properly grounded.Screw the UPC Open into an enclosed panel using the mounting slots

on the coverplate. Leave about 2 in. (5 cm) on each side of the controller for wiring. Mounting hole dimensions 4.8

in. (12.2 cm) between mounting slot center lines.

Wiring the UPC Open for power

CAUTION The UPC Open is powered by a Class 2 power source. Take appropriate isolation measures when

mounting it in a control panel where non-Class 2 circuits are present. The UPC Open is a half wave device. Half

wave and full wave devices cannot share power. Examples of a full wave device are a CVC or ICVC in an applied

chiller.

Carrier controllers can share a power supply as long as you:

• Maintain the same polarity

• Use the power supply only for Carrier Open controllers

Installing the UPC Open

To wire for power

1 Remove power from the power supply.

2 Pull the screw terminal connector from the controller's power terminals labeled Gnd and Hot.

3 Connect the transformer wires to the screw terminal connector.

NOTE If using a grounded transformer, connect the ungrounded lead to the Hot terminal to avoid damaging

the transformer.

4 Apply power to the power supply.

5 Measure the voltage at the UPC Open’s power input terminals to verify that the voltage is within the operating

range of 21.6–26.4 Vac.

6 Insert the screw terminal connector into the UPC Open's power terminals.

7 Verify that the Power LED is on and the Run LED is blinking.

Addressing the UPC Open

EIAYou must give the UPC Open a MAC address that is unique on the MS/TP or ARCNET network. You can address

the UPC Open before or after you wire it for power

1 If the UPC Open has been wired for power, pull the screw terminal connector from the controller's power

terminals labeled Gnd and Hot. The controller reads the address each time you apply power to it.

2 Using the rotary switches, set the controller's address. Set the Tens (10's) switch to the tens digit of the

address, and set the Ones (1's) switch to the ones digit.

EXAMPLE If the controller’s address is 25, point the arrow on the Tens (10's) switch to 2 and the arrow on

the Ones (1's) switch to 5.

10's

1's

CAUTION The factory default setting is 00 and must be changed to successfully install your UPC Open.

Wiring for communications

The UPC Open communicates using BACnet on the following types of network segments:

•MS/TP communicating at 9600 bps, 19.2 kbps, 38.4 kbps, or 76.8 kbps

•ARC156 communicating at 156 kbps

NOTE For more networking details, see the Open Controller Network Wiring Installation Guide.

Installing the UPC Open

Wiring specifications for BACnet MS/TP and ARC156

Cable:

22 AWG or 24 AWG, low-capacitance, twisted, stranded, shielded copper wire

Maximum length:

2000 feet (610 meters)

WARNING Do not apply line voltage (mains voltage) to the controller's ports and terminals.

To wire the controller to the BACnet network

1 Pull the screw terminal connector from the controller's power terminals labeled Gnd and Hot.

2 Check the communications wiring for shorts and grounds.

3 Connect the communications wiring to the controller’s screw terminals labeled Net +, Net -, and Shield.

NOTE Use the same polarity throughout the network segment.

4 Set the communication type and baud rate.

For...

Set DIP switches 1 and 2

to...

DIP switch 3

Set DIP switch 4

to...

Set DIP switches 5 through 8 to...

MS/TP (m)

The appropriate baud

rate. See the MS/TP

Baud diagram on the

controller.

N/A

Off/Off/Off/Off

ARC156

N/A. Baud rate will be

156 kbps regardless of

the DIP switch settings.

N/A

Off

N/A

NOTE Use the same baud rate for all controllers on the network segment.

5 For MS/TP, verify that the EIA-485 jumpers are set to EIA-485 and 2w.

6 Wire the controllers on a BACnet MS/TP or BACnet ARC156 network segment in a daisy-chain configuration.

7 If the UPC Open is at either end of a network segment, connect a BT485 to the UPC Open.

8Insert the power screw terminal connector into the UPC Open's power terminals.

9 Verify communication with the network by viewing a Module Status report in the i-Vu® interface.

Altri manuali per UPC Open

Indice

Altri manuali Carrier Convertitore multimediale

Carrier

Carrier UPC Open Guida rapida alla configurazione

Manuali Convertitore multimediale popolari di altre marche

SoundTraxx

SoundTraxx Blunami BLU-2200 Manuale utente

SPROLINK

SPROLINK VA1 Manuale utente

Acclaim Lighting

Acclaim Lighting DDC-1-AC Manuale utente

Nikon

Nikon AF-S TC-20E III Manuale utente

Axis

Axis AXIS Q7406 Manuale utente

Omega

Omega TAC80B-J Manuale utente

Zoom

Zoom Thunderbolt TAC-2R Manuale utente

OST

OST iConverter 10/100M Manuale utente

Vertiv

Vertiv Netsure Manuale utente

birddog

birddog MINI Manuale utente

Roland

Roland GI-10 Manuale utente

Wallenstein

Wallenstein WX310 Manuale utente

Pace

Pace MSS 200-1 Manuale utente

Solar Converters

Solar Converters EQ 12/24-50 Manuale utente

CYP

CYP EL-7400V Manuale utente

TIE

TIE MIDI 1i1o Manuale utente

DCS

DCS Vivaldi Upsampler Manuale utente

Westermo

Westermo MCW-211 SERIES Manuale utente