CARVIN V3M Manuale utente

- 1 -

How to bias:

V3M

Rev A

9/22/2011

www.carvinservice.com

- 2 -

Only a certified technician should bias Carvin amps, this is very

dangerous, you can get hurt, please be very careful when working

with any tube amp!

If you have changed the tubes make sure they are a matched set.

-The Bias for the V3M, V3MC should be 80mA at 50W setting, with 120VAC.

STEP 1

These are the tools you will need:

1. A flat head screw driver “small”.

2. A multi-meter, w/ milli amp

reading.

3. Banana to clip leads.

4. Drill

5. Amp stand (optional).

STEP 1A

You have to remove the bottom cover by

removing the screws as indicated. It’s a total of

10 screws.

STEP 2 Set it in an amp stand. Be very careful with the

tubes they can break.

NOTE: If you don't have an amp stand then

support the chassis on some blocks of wood so

that the power tubes are not touching anything -

they get very hot

- 3 -

STEP 3

Plug in speaker to output 1 or 2, they are

both the same, both jacks are in parallel.

NOTE: For speaker setup click on

“Troubleshooting” and “Speakers”.

IMPORTANT: Do NOT turn on the

amplifier without a speaker plugged in!

STEP 4

Make sure the OHM setting is correct.

Improper setting will result in damage to

the amp!

NOTE: On the back is where you will

find the OHM setting, make sure the

speaker matches the OHM setting.

STEP 5

Set the switch in the back to 50W.

NOTE: This step is very important, if

you don’t set this to 50W setting you will

not get the correct bias setting when you

adjust it later in the procedures.

- 4 -

STEP 6

A) Lower the volume down on All channels.

B) Unplug your guitar cord from the input of the amp.

NOTE: If you have signal going through

the amp, it will not be the true reading,

when you set the bias.

STEP 7

A) Connect the leads to the meter. B) Set your meter to the milliamp (mA) position.

Make sure the fuse inside is good. Set meter to DC Current, not AC current.

NOTE: If the Fuse inside your meter is open, the meter will never work. It will

always read 0mA. In the meter above, mA and COM is selected, you have the

option to plug in the lead on (A) but because the setting will be set to 80mA it’s

best to use mA.

STEP 8

1. 2.

Connect clips from meter to Standby Switch. It’s easier to clip the leads to the

wires that go from the standby switch to the main circuit, see picture above.

IMPORTANT: Never power the amp ON before connecting the leads, you will

get a big spark, you may blow the fuse of the Meter and or damage the amp.

- 5 -

STEP 9

Plug in AC Cord.

NOTE: Sometimes when the AC Cord is

new it does not want to go in all the way.

Push firmly to force it in, if that is the

case.

STEP 10

Turn the Power Button ON. Wait 2

minutes for the amp to get hot, after the 2

minutes you should see the meter read

current. Your Meter will start low then

increase up to 80mA, adjust it accordingly.

NOTE: Do Not turn ON the Standby

switch, leave it on STANDBY.

STEP 11

Check your meter at this point, if it goes

over 80mA, lower it by turning the bias

potentiometer with the screw driver, clock

wise, if it’s under 80mA bring it up by

turning the potentiometer the other way.

Bias Potentiometer above.

- 6 -

It is OK and normal for the bias reading to fluctuate a little bit and may not be

exactly 80mA but as close as possible.

IMPORTANT: Set your meter to DC Current, your meter should read (mA)

Good Bias

STEP 12

Power down Steps:

1. Turn OFF the amp

2. Disconnect the meter leads.

3. Unplug your AC cord and wait for the tubes to cool down, so that you can put

back the bottom lid.

IMPORTANT: During biasing and normal amp operation if there is a burning smell

or loud crackling noise that comes from the speaker, you should turn off the amp as

your may have a bad tube. The same is true if your meter reads higher that 150mA

or goes into overload. The tubes should never glow RED on the gray plate material,

the largest metal part inside the tube. This indicates a major problem and extremely

unsafe condition. If this happens turn off the amp immediately!

IMPORTANT: The tubes get very hot! Don’t touch them, you will burn your

skin if you do. If the amp is ON the tubes will get hot, even if you are not

playing the amp, wait 30 minutes before handling the unit to ensure the amp

cooled down.

IMPORTANT: This is not the only way to set the bias on this amp, this is the

Carvin Approved method which is used on the Production line in the San Diego,

California Factory.

- 7 -

NOTE: If the tubes are getting hot and 3 to 5 minutes went by and you don’t see

any reading on your meter check your meter, you may have the leads connected to

the wrong place in your meter or the fuse on the meter is open.

EXPORT(230-240VAC 50Hz): Follow the same instructions.

Comments or questions email us at Carvinservice@carvin.com

www.carvinservice.com

Indice

Altri manuali CARVIN Amplificatore

Manuali Amplificatore popolari di altre marche

ASTRO

ASTRO HVO V40 P Manuale utente

Marantz

Marantz SUPERSCOPE BLA-545 Istruzioni per il montaggio

NAD

NAD CI980 Manuale utente

Technics

Technics SE-CH770 Manuale utente

Harman Kardon

Harman Kardon HK6300 Manuale utente

NAD

NAD T975 Manuale utente

McIntosh

McIntosh MA6850 Manuale utente

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manuale utente

Viatron

Viatron Autrix Manuale utente

GME

GME GA9800 Manuale utente

Atlas

Atlas CP700 Manuale utente

Roland

Roland KC-1000 Manuale utente

Pyle

Pyle PFMRA350BW Manuale utente

Advantage

Advantage S-250 Manuale utente

IRT Electronics

IRT Electronics DVA-3007 Manuale utente

Dimavery

Dimavery BA-100 Series Manuale utente

Sony

Sony XM-S400D Manuale utente

Schertler

Schertler ROY X Manuale utente