Cary Audio Design CAD-308 SA Scheda tecnica

CAD-308 SA

Hybrid Stereo Power Amplifier

Operation and Installation Manual

NOTE: Please read this manual carefully before installing your new amplifier into your stereo system. It

contains important set up and installation information as well as safety warnings regarding high AC voltage

inside the chassis.

Dear Audiophile Friend:

I would like to thank you for buying a CAD-308 SA hybrid power amplifier. You will find

many desirable features on your new power amplifier. These include high quality RCA

input connectors, excellent quality speaker terminals, dual output level meters, a 200%

duty cycle power transformer, a fully regulated three stage power supply for high

voltage stages, filament voltage for the tubes and for the solid state output devices.

The best feature of the CAD-308 SA is its spacious and powerful sonic presentation.

The 12AU7 triode tubes (5814 Joint Army Navy [JAN] military surplus vacuum tubes may be

substituted.) we have used in the driver stage are considered to be some of the very finest

sounding dual triode tubes. Please read the instruction manual so that you are familiar

with the operation of your new CAD-308 SA hybrid power amplifier.

Thank you again for your interest in and continued support of Cary Audio Design.

Dennis J. Had

President

Specifications: CAD 308 SA Hybrid Power Amplifier

Dimensions: 17 _” W x 4 _” H x 14 _” D (~ 44.4 cm x 11.4 cm x 36.8 cm)

Weight: 18.75 lb. (8.52 kg)

Circuit: Class A Triode vacuum tube driver stage, Class AB solid state output

stage

Frequency Response: 8 Hz - 150 kHz + 0, - 3 dB

THD/IMD @ rated output: 0.02% @ 50 watts per channel, 8 ohm load

Input Impedance: 100,000 ohms resistive (100 K W)

Gain: 20 dB

Signal/Noise Level: > 95 dB

Resistors: 1 % precision metal film

Capacitors: Precision film and foil capacitors

Power Transformer: 200% continuous commercial duty cycle, 225 VA rating

Tubes: 2- 12AU7 dual triodes,

5814 Joint Army Navy (JAN) surplus tubes may be substituted

Power Supply: Three stage, full wave rectification, center-tapped, pi-network with filter

choke, fully regulated

AC Power Requirements: 100 – 130 volts AC / 50-60 Hz at 240 watts

200 – 245 volts AC / 50-60 Hz at 240 watts

Internal Wiring: EE Teflon dielectric Silver wire

Warm-up Time: 5 minutes (1 minute auto mute)

Input Jacks: Gold plated with Teflon dielectric inserts

Speaker Binding posts: High quality gold plated 5 way binding posts

Duty Cycle: Continuous duty 24 hours per day.

Specifications are subject to change or improvement without notice or obligation.

Front Panel Features

Power Switch: 2 position rocker switch off/on controls the AC line voltage

On LED: Indicates internal power supply is power up

Operate LED: Each channel, Indication of time delay release (approximately 1 minute)

Dual Output Level Meters: These high quality meters are designed to show power

output levels from the power amplifier.

Rear Panel Features

AC Connector: Inlet for the detachable AC power cord, standard IEC plug

RCA Input Connections: Gold plated brass with Teflon dielectric insulation

AC Fuse: !!VERY IMPORTANT!! ONLY USE 3 AMP Slow Blow FUSE

Remote Trigger: Female 2 circuit jack, 12 VDC @ 400 ma rating (Optional feature)

WARNING!

MAKE NO ATTEMPT TO PUT THE AMPLIFIER IN SERVICE WITH THE

COVER OFF. CONTACT WITH THE AC VOLTAGE INSIDE THE

CHASSIS CAN BE FATAL !

Shipping and Packing

All our shipping cartons have been especially designed to protect their contents and

special care has been taken to prevent damage under normal conditions. Mishandling

should be evident upon inspection of the shipping container. If damage is found after

visual inspection, do not destroy the evidence. If necessary, document the damage with

photographs and contact the transport carrier immediately.

Carefully remove your new amplifier from its packing carton and examine it closely for

signs of shipping damage. It is recommended to save all original packing cartons to

protect your hybrid power amplifier should you wish to store it or ship it for after-sales

service.

Warranty Card

If you are the original USA purchaser of this hybrid power amplifier and purchased it for

use within the United States, you should fill out the enclosed warranty registration card

and return it to Cary Audio Design, within 15 days of your purchase or register online

at www.caryaudio.com. Warranty restrictions and applications may apply. Consult the

warranty section of this manual.

Warranty Outside the USA

Consult your local Cary Audio Distributor for your local terms of warranty.

CAD-308 SA Placement

The power amplifier is designed for use inside of homes. It must be protected from the

elements and temperature extremes. For example, avoid placing the unit in extremely

hot locations such as near or on top of radiators or other home heating devices. Its

location among the user’s home audio components is not critical. Avoid moisture, dust

and locations with high vibration. Keep the amplifier vents free from obstruction and

allow at least 6 inches (15 cm) open space above the amplifier for proper ventilation. Do

not install in a sealed cabinet without ventilation as the amp will overheat. Rack

mounting or similar installs are possible if the cabinet is well ventilated or has forced air

cooling with a fan.

Power Requirements

The CAD-308 SA is designed to operate from AC house current mains. The design

voltage is 120 Volts AC at 50/60 Hz. Export units have settings for 100/200/220/240

Volts AC at 50/60 Hz.

Interconnect Cables

The RCA interconnect cables to the input jacks on the power amplifier can be any

convenient length your set up requires. The choice of a high quality shielded

interconnect cable is important in most installations. Your Authorized Cary Audio Design

Dealer will have proper interconnect cables in stock for this purpose. The low output

impedance of the CAD-308 SA solid state output stage will allow it to will run long

speaker wire runs without a problem. Choose 14 gauge wire as a minimum wire size

and consider 12 gauge wire or larger for longer runs over 25 feet long. We believe

different types of speaker wires make a difference in the sound of the system and

suggest discussing them with your dealer. Please be certain that no speaker wire strands

bridge the gap between the speaker output terminals when wiring the speakers. This will

cause the amplifier to shut off if it happens.

Operation

Your new CAD-308 SA hybrid power amplifier is ready for operation after the various

interconnect cables and speaker wires have been installed and the unit is plugged into

the household AC mains 120 Volt AC wall socket.

Power Rocker Switch

The power rocker switch is located at the left side on the CAD-308 SA hybrid power

amplifier front panel. The switch operates in the following manner:

OFF (Down position) Removes all AC voltages from the CAD-308 SA power supply.

ON (Up position) Turns the AC voltage to the power transformer primary on. We

recommend that the AC power switch be left in the ON position at all

times. The CAD-308 SA sounds better after an initial 100 hour burn in period

and when warmed up for _ hour in daily use.

Operate LED’s: These blue LED’s light up after the CAD-308 SA is fully warmed up and

ready to operate. The delay time is about one minute.

Output Level Meters

The dual front panel output level meters show the relative output level in watts. These

are average level meters and will respond to ‘longer time constant’ signals. We have

chosen to have average level meters since these more nearly reflect the long term

power levels that are driving your speakers.

WARNING!

MAKE NO ATTEMPT TO PUT THE AMPLIFIER INTO SERVICE WITH

THE TOP OFF OR THE CABINET OPEN. NEVER OPERATE THE CAD-

308 SA WITH THE TOP COVER REMOVED. CONTACT WITH THE

OPERATING VOLTAGES PRESENT INSIDE CAN BE FATAL!

Factory Service

If it becomes necessary to replace any parts, the same brand and part number and style

should be used. New parts are available from Cary Audio Design, Inc. 1020 Goodworth

Drive, Apex, North Carolina, 27539.

Careful consideration has been given to the design of your new hybrid power amplifier

to keep maintenance problems to a minimum; however, it is possible that some

problems may arise. If this occurs, we suggest contacting our Customer Service

Department at phone number 919-355-0010 from 1 to 5 PM, East Coast time to

describe your problem in detail. Do not return the CAD-308 SA to the factory without

a Return Authorization Number (RMA number) from the Customer Service

Department. As the packing and shipping is being done by others, Cary Audio Design

will assume no responsibility if the transportation company refuses to pay a damage

claim due to your improperly packing or for lack of insurance should the unit be lost or

damaged in shipment from you to us.

Technical Support

If you ever should need it, Technical Support for Cary Audio Design components is

available from 1 to 5 PM Monday through Friday at 919-355-0010. We value your

opinions and suggestions as well! Thanks again for buying a Cary Audio Design

component for your home stereo!

Replacing the Input Driver Tubes

If you ever need to change an input driver tube (or you wish to try other brands for

sound quality reasons) unplug the amplifier before opening the cabinet. We suggest that

you change both of the 12AU7 or 5814 tubes at the same time to keep them matched

for total hours of use. Any current production or new old stock (NOS) 12AU7, 5814 or

equivalent tubes will work very well in the CAD 308 SA hybrid power amplifier. We

choose to operate tubes in the ‘sweet spot’ of their operating characteristics, not near their

operational limits. As a result, the input tubes should last for years in this design.

WARNING!

Please do not touch any of the internal parts other than the

vacuum tubes as there are potentially lethal high voltages stored

in the power supply section.

Cary Audio Design

1020 Goodworth Drive

Apex, North Carolina 27539

Tel: 919-355-0010

Fax: 919-355-0013

[email protected]

www.caryaudio.com

Indice

Altri manuali Cary Audio Design Amplificatore

Cary Audio Design

Cary Audio Design SLP-308 Scheda tecnica

Cary Audio Design

Cary Audio Design SLP-98L Manuale utente

Cary Audio Design

Cary Audio Design LPP-1 Manuale utente

Cary Audio Design

Cary Audio Design Cinema 8 Manuale utente

Cary Audio Design

Cary Audio Design CAD-300SSE Manuale utente

Cary Audio Design

Cary Audio Design CAD-40M Manuale utente

Cary Audio Design

Cary Audio Design CAD 808 Manuale utente

Cary Audio Design

Cary Audio Design CAD 120S Manuale utente

Cary Audio Design

Cary Audio Design CAD-100 Manuale utente

Cary Audio Design

Cary Audio Design CAD-805 Anniversary Edition Manuale di istruzioni

Cary Audio Design

Cary Audio Design CAD-300S SE Manuale utente

Cary Audio Design

Cary Audio Design 7.125 Manuale utente

Cary Audio Design

Cary Audio Design CINEMA 6 Manuale utente

Cary Audio Design

Cary Audio Design CAD 2A3MB Manuale utente

Cary Audio Design

Cary Audio Design CAD 120S Manuale utente

Cary Audio Design

Cary Audio Design 7.125 Manuale utente

Cary Audio Design

Cary Audio Design CAI 1 Manuale utente

Cary Audio Design

Cary Audio Design CAD 211 AE Manuale utente

Cary Audio Design

Cary Audio Design CPA 1 Manuale utente

Cary Audio Design

Cary Audio Design Cinema 8 Manuale utente

Cary Audio Design

Cary Audio Design Cinema 2 and Manuale utente

Cary Audio Design

Cary Audio Design PH 302 MKII Manuale utente

Cary Audio Design

Cary Audio Design SLP-94 Manuale utente

Cary Audio Design

Cary Audio Design Cinema 7B Manuale utente

Manuali Amplificatore popolari di altre marche

ASTRO

ASTRO HVO V40 P Manuale utente

Marantz

Marantz SUPERSCOPE BLA-545 Istruzioni per il montaggio

NAD

NAD CI980 Manuale utente

Technics

Technics SE-CH770 Manuale utente

Harman Kardon

Harman Kardon HK6300 Manuale utente

NAD

NAD T975 Manuale utente

McIntosh

McIntosh MA6850 Manuale utente

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manuale utente

Viatron

Viatron Autrix Manuale utente

GME

GME GA9800 Manuale utente

Atlas

Atlas CP700 Manuale utente

Roland

Roland KC-1000 Manuale utente

Pyle

Pyle PFMRA350BW Manuale utente

Advantage

Advantage S-250 Manuale utente

IRT Electronics

IRT Electronics DVA-3007 Manuale utente

Dimavery

Dimavery BA-100 Series Manuale utente

Sony

Sony XM-S400D Manuale utente

Schertler

Schertler ROY X Manuale utente