Castle Creations Copperhead 10 Manuale utente
Revised / Copyright © Cstle Cretions P/:--
ABOUT THE COPPERHEAD 10
Motors
Plese note tht while the Copperhed is cpble of hndling significnt
power, your motor must lso be up for the tsk. Alwys run your motor within
the mnufcturer’s specs. onitor motor, bttery, nd controller temps crefully
nd never let the motor get bove ° C (° F). Excessive het in the motor cn
dmge the motor, the Copperhed , nd the btteries.
Gearing
Alwys strt with stock gering. If you wish to chnge the gering, motor, or
bttery, check your motor temperture often on the first run. If the motor gets
too hot, increse the spur size, reduce the pinion size, or reduce the pck voltge.
Programming
The Copperhed is progrmmble vi trnsmitter (see
Driver’s Ed Guide
) or
settings my be progrmmed vi computer with Cstle Link USB dpter (coupon
for free dpter included in pckge). You cn lso progrm with mobile device
using Cstle B•Link Bluetooth® Adpter (sold seprtely). See the Drivers’ Ed
Guide for more instructions on trnsmitter progrmming nd the Cstle Link system
(
“Tuning with Cstle Link” nd “Trnsmitter Progrmming”
).
Data Log Lite
The Copperhed fetures
Dt Log Lite
. You will be ble to mesure nd record
importnt power system informtion during your rce, turn-by-turn. After your
run, you cn downlod nd nlyze this log using Cstle Link. You will be ble to
inspect mny prmeters including bttery voltge, motor RP, ESC temperture
nd more.
Dt Log Lite
mximizes use of memory spce by providing ccess to
the most importnt dt vilble. Additionl informtion bout using the dt
logging fetures cn be found in the Driver’s Ed Guide (“Dt Logging”).
orth Rogers Rod, Olthe, KS
() - (ext. # Support, # Service)
Product Support: cstlecretions.com/contct-support
Service: cstlecretions.com/contct-service
Website: www.cstlecretions.com
COPPERHEAD 10 SPECIFICATIONS
Application
Guidelines /th scle RC Hobby vehicles weighing up to .lbs.
Input Voltage
Range in: S LiPo, x: S LiPo, .V (Do not use S LiHV)
BEC
Specifications Selectble, .V or .V (A pek), defult .V.
Sensors Yes, with pre-instlled otor Sensor Hrness (dust cover
included in pckge).
Product Use
Statement
• Applying voltges higher thn .V will cuse irreprble
dmge to your controller.
• The Copperhed 10 is high-performnce controller; you must
use high-dischrge cells in your high-performnce ppliction
to ensure vehicle performnce
(see Driver’s Ed Guide, “A ord
About Btteries”).
• The Copperhed 10 requires the use of connectors designed for
50+ mps continuous. Ex. Cstle 4.0mm Polrized Connectors
(Driver’s Ed Guide, “Connectors nd Power iring”).
• The Copperhed is not intended for humn or niml
propulsion.
• Filure to dhere to the
Product Use Sttement
constitutes
violtion of the wrrnty greement, nd will result in non-
wrrnty service fees to repir or replce dmged products.
TRANSMITTER PROGRAMMING REFERENCE
*Defult Setting
AUDIBLE ALERT REFERENCE
• • Strt Fil
•
–
Low Voltge Cutoff
• • • Sensors Lost
• •
–
Rdio Glitch
•
–
• Over-Temperture
–
•
–
BEC Over-Temperture
• • • • Dt Log Full rning
–
–
• otor Over-Temperture
1. Brake/Reverse Type
• ith Reverse*
• ithout Reverse
• Crwler Reverse
2. Voltage Cutoff
• Auto-Lipo*
• one
3. Brake Amount
• %
• %*
• %
• %
4. Drag Brake
• Disbled*
• %
• %
• %
• Crwler Full On
5. Motor Type
• Brushless*
• Brushed Reversing
6. Motor Direction
• orml*
• Reversing
DRIVER’S ED GUIDE
For more detiled informtion regrding Getting Strted,
Throttle Clibrtion, using Cstle Link, or Trnsmitter
Progrmming, plese red the Driver’s Ed Guide by visiting:
www.cstlecretions.com/CH10DEG
Or scn this QR code with your smrt device to open the link.
Fan Wire
Negative Battery Wire
Motor Sensor Harness
Waterproof
Switch
RX Wire
Positive Battery Wire
Removable 30mm Fan Replaceable Fan Cover
Motor A
Motor B
Motor C
Status
LEDs
Motor Sensor Dust Cover
GETTING STARTED
. Solder high qulity bttery connector to the ESC (see
Driver’s Ed Guide
“Connectors nd Power iring”
).
. ount the ESC nd motor into the vehicle.
. Connect motor to the ESC (see
Driver’s Ed Guide, “otor iring”
).
. Instll the sensor dust cover or connect the motor sensor hrness nd wire
(necessry to retin the RX wire).
. Plug in the RX wire into throttle (#) nd fn wire into uxiliry (#/#).
6. Clibrte your ESC to your rdio. (See below).
YOU ARE NOW READY TO GO!
THROTTLE CALIBRATION
1. Rdio on, bttery plugged in, ESC o.
2. Hold full throttle, turn ESC on (green LED).
3. hen red LED flshes, go to full reverse.
4. hen yellow LED flshes, go to neutrl.
5. Armed nd redy! NOTE: ot intended for opertion while submerged in liquid. If unit is operted in wet
conditions, rinse with fresh wter to remove dirt or corrosives, then fully dry unit. Fn is
not wter resistnt. Remove the fn from the ESC before exposure to liquids.
