CAVE TeamUp TX20i Manuale utente

CAVE-TEK TeamUp TX20i Camera User Guide

CAVE-TEK

TeamUp TX20i Camera

User Guide

English (V1.0)

CAVE-TEK TeamUp TX20i Camera User Guide 
 
Table of content 
1Packing List 1 
2Quick Start 1 
3About TX20i 2 
1 Interfaces and Buttons 2 
2 Dimension 2 
3 Remote Control 3 
4 RS-232 Interface 4 
5 Serial Communication Control 4 
4GUI Settings 5 
1 MENU 5 
2 EXPOSURE 5 
3 COLOR 6 
4 IMAGE 6 
5 P/T/Z 7 
6 NOISE REDUCTION 7 
7 SETUP 7 
8 COMMUNICATION SETUP 8 
9 RESTORE DEFAULT 8 
5Network Function 9 
1 Operating Environment 9 
2 Equipment Installation 9 
3 Internet Connection 9 
4 Camera controlled by LAN 9 
4.1 Setup IP address 9 
4.2 Login IP Camera admin 10 
4.3 Open Network stream with VLC player 11 
5 Camera Setup 12 
5.1 Homepage Introduction 12 
5.2 Video Settings 14 
5.3 Image Settings 15 
5.4 Audio Settings 16 
5.5 System Settings 17 
5.6 Network Settings 17 
5.7 Device Information 18 

CAVE-TEK TeamUp TX20i Camera User Guide

1 Packing List

Open the box, you will find below items:

Name

Quantity

TeamUp TX20i Camera

AC Power Adaptor

Power Cable

RS232 Cable

Mount Kit

Remote Control

Quick Installation Guide

2 Quick Start

1) Please check below connects first.

2) Connect the power adapter to the power connector on the rear panel of the camera. The power

indicator on the front panel of the camera is on.

3) After the camera is powered on, it starts to boot up to the initialization position. Then both horizontal

and vertical go to the middle position, the motor stops running, and the initialization is completed.

(Note: If preset 0 is saved, Camera will be moved to preset 0)

CAVE-TEK TeamUp TX20i Camera User Guide

3 About TX20i

3.1 Interfaces and Buttons

Item

Name

AUDIO IN Interface

LINE OUT Interface

System Select Switch

RS485 Interface

RS232 IN Interface

RS232 OUT Interface

Network Interface

HDMI Interface

USB 3.0 Interface

3G-SDI Interface

DC 12V Interface

Power Switch

3.2 Dimension

CAVE-TEK TeamUp TX20i Camera User Guide

3.3 Remote Control

Key Description

1. Standby Key

Press this button to enter standby mode. Press it

again to enter normal mode.

2. Number Key

To set preset or call preset.

3. *Key

To configure the special function key.

4. Preset Key

Set preset: Store a preset position.

[SET PRESET] + Numeric button (0-9): Setting a

corresponding numeric key preset position.

5. HOME Key

Confirm the selection, or move the camera back to

the middle position

6. Return Key

Return to the previous menu

7. Zoom Key

Slow Zoom: Zoom In [+] or Zoom Out [-] slowly

Fast Zoom: Zoom In [+] or Zoom Out [-] fast

8. Left/Right Setting Key

Press with 1 button and 2 buttons setting the

direction of the Pan-Tilt.

●Simultaneously press L/R Set +1[STD]: set the

Pan-Tilt to turn the same direction as the L/R

Set.

●Simultaneously press L/R Set +2[REV]: set the

Pan-Tilt to turn the opposite direction as the

L/R Set.

9. Focus Key

To adjust the focus.

Press [AUTO] adjust the focuses on the center of

the object automatically. Or to adjust the focus

manually.

Press [MANUAL] adjusts the focus on the center of

the object manual.

10. Selection Key

Press the button corresponding to the camera you

want to operate with the remote controller.

11. #Key

To configure the special function key.

12. IR Remote Control Key

[*]+[＃]+[F1]: Address 1

[*]+[＃]+[F2]: Address 2

[*]+[＃]+[F3]: Address 3

[*]+[＃]+[F4]: Address 4

13. Reset Key

Clear preset: Erase a preset position.

[CLEAR PRESET] + Numeric button (0-9)

Or: [*]+[#]+[CLEAR PRESET]: Erase all the preset

individually.

14. PTZ Control Key

Press arrow buttons to perform panning and tilting.

Press [HOME] button to face the camera back to

front.

15. Menu Key

MENU: enter or exit OSD MENU.

16. Backlight Key

BLC ON/OFF: Press this button to enable the

backlight compensation. Press it again to disable

the backlight compensation.

17. PTZ Reset Key

Preset Pan/Tilt self-test.

18. Special Function Key

[*]+[＃]+[1]: Change OSD menu to English

[*]+[＃]+[4]: Display current IP address

[*]+[＃]+[6]: Reset to system defaults

[*]+[＃]+[8]: Display camera firmware Info.

[*]+[＃]+[9]: set mounting mode (normal / vertical

flip)

[＃]+[*]+[4]: Set Network configuration to DHCP

[*]+[＃]+[Manual]: Reset network to default.

[*]+[＃]+[F1]: Assign Camera to IR Address 1

[*]+[＃]+[F2]: Assign Camera to IR Address 2

[*]+[＃]+[F3]: Assign Camera to IR Address 3

[*]+[＃]+[F4]: Assign Camera to IR Address 4

CAVE-TEK TeamUp TX20i Camera User Guide

3.4 RS-232 Interface

No.

Function

DTR

DSR

TXD

GND

RXD

GND

IR OUT

The correspondence between the camera and

Windows DB-9 pin:

The correspondence between the camera and

the Mini DIN pin:

3.5 Serial Communication Control

●RS232 Communication Control

The camera is controlled via RS232. The RS232 serial port parameters are as follows:

Baud rate: 2400/4800/9600/38400 bit/s;

Starting Position: 1 bit

Data bit: 8 bits

Stop bit: 1 bit

Check digit: None

●RS485 Communication Control

Control camera via RS485, half-duplex mode:

Baud rate: 2400/4800/9600/38400 bit/s;

Starting position: 1 bit

Data bit: 8 bits

Stop bit: 1 bit

Check digit: None

●List of protocols

For a detailed list of VISCA/Pelco-D/Pelco-P protocols, please check www.cave-tek.com.

9.RI

8.CTS

8.NC

7.RTS

7.IR OUT

6.DSR

6.GND

5.GND

5.RXD

4.DTR

4.GND

3.TXD

2.RXD

2.DSR

1.CD

1.DTR

Windows DB-9

Camera

4.GND

8.NC

7.NC

7.IR OUT

6.GND

5.RXD

3.TXD

2.DSR

1.DTR

Mini DIN

Camera

CAVE-TEK TeamUp TX20i Camera User Guide

4 GUI Settings

4.1 MENU

Press the [MENU] button to display the main menu on the display, using the arrow button to move the

cursor to the item. Press the [HOME] button to enter the corresponding sub-menu.

Exposure

Color

Image

P/T/Z

Noise Reduction

Setup

Communication Setup

Restore Default

[Home] Enter

[Menu] Exit

4.2 EXPOSURE

Move the main menu cursor to [EXPOSURE], and press [HOME] key enter the exposure page, as shown in

the following figure.

EXPOSURE

Mode

Auto

ExpCompMode

ExpComp

Backlight

Off

Gain Limit

Anti-Flicker

50Hz

Meter

Average

DRC

Select Item

Change Value

[Menu] Back

Mode: Exposure mode, Auto, Manual, SAE, AAE, Bright.

ExpCompMode: Exposure the compensation mode, On, Off (Effective only in Auto mode).

ExpComp: Exposure the compensation value, -7~7 (Effective only in ExpCompMode item to On).

Backlight: Set the backlight compensation, On, Off (Effective only in Auto mode).

Bright: Intensity control, 0~17 (Effective only in Bright mode).

Gain Limit: Maximum gain limit, 0 ~ 15 (Effective only in Auto, SAE, AAE, Bright mode).

Anti-Flicker: Anti-flicker, Off, 50Hz, 60Hz (Effective only in Auto, AAE, Bright mode).

Meter: Average, Center, Smart, Top.

DRC: DRC strength, 0 ~ 8.

CAVE-TEK TeamUp TX20i Camera User Guide

4.3 COLOR

Move the main menu cursor to [COLOR], and press [HOME] key enter the color page, as shown in the

following figure.

COLOR

WB Mode

Auto

RG Tuning

BG Tuning

Saturation

100%

Hue

AWB Sens

High

Select Item

Change Value

[Menu] Back

WB-Mode: White balance mode, Auto, Indoor, Outdoor, One Push, Manual, VAR.

RG Tuning: Red gain fine-tuning, -10 ~ +10 (Effective only in Auto, One Push, VAR mode).

BG Tuning: Blue gain fine-tuning, -10 ~ +10 (Effective only in Auto, One Push, VAR mode).

Saturation: 60% ~ 200%.

Hue: 0 ~ 14.

AWB Sens: The white balance sensitivity, Low, Middle, High.

4.4 IMAGE

Move the main menu cursor to [IMAGE], and press [HOME] key enter the image page, as shown in the

following figure.

IMAGE

Luminance

Contrast

Sharpness

Flip-H

Off

Flip-V

Off

B&W-Mode

Off

Gamma

0.5

Style

Clarity

Select Item

Change Value

[Menu] Back

Luminance: 0 ~ 14.

Contrast: 0 ~ 14.

Sharpness: Auto, 0 ~ 15.

Flip-H: On, Off.

Flip-V: On, Off.

B&W-Mode: On, Off.

Gamma: Default, 0.45, 0.5, 0.56, 0.63.

Style: Default, Norm, Clarity, Clarity (LED), Bright, Soft, 5S.

CAVE-TEK TeamUp TX20i Camera User Guide

4.5 P/T/Z

Move the main menu cursor to [P/T/Z], and press [HOME] key enter the P/T/Z page, as shown in the

following figure.

P/T/Z

SpeedByZoom

AF-Zone

Center

AF-Sense

High

L/R Set

STD

Display Info

Image Freeze

Off

DigitalZoom

Call Preset Speed

Pre Zoom Speed

Select Item

Change Value

[Menu] Back

SpeedByZoom: The depth of field scale switch, On, Off.

AF-Zone: Interested in focusing area, Top, Center, Bottom.

AF-Sense: Automatic focusing sensitivity options, Low, Normal, High.

L/R Set: STD, REV.

Display Info: On, Off.

Image Freeze: On, Off.

Digital Zoom: Off, 2x, 4x, 8x, 16x.

Call Preset Speed: 1 ~ 24.

Pre Zoom Speed: 0 ~ 7.

4.6 NOISE REDUCTION

Move the main menu cursor to [NOISE REDUCTION], and press [HOME] key enter the noise reduction page,

as shown in the following figure.

NOISE REDUCTION

NR2D-Level

Off

NR3D-Level

Select Item

Change Value

[Menu] Back

NR2D Level: 2D noise reduction, Off, Auto, 1 ~ 5.

NR3D Level: 3D noise reduction, Off, 1 ~ 8.

4.7 SETUP

Move the main menu cursor to [SETUP], and press [HOME] key enter the setup page, as below.

SETUP

Language

DVI Mode

DVI

Auto Scan Shoot

Off

Auto Inversion

SDI-3G Mode

Level-A

Tracking

Tally Mode

[Home] Enter

[Menu] Back

Language: EN, Chinese, Russian.

DVI Mode: DVI, HDMI.

CAVE-TEK TeamUp TX20i Camera User Guide

Auto Scan Shoot: On, Off.

Auto Inversion: On, Off.

SDI-3G Mode: LEVEL-A, LEVEL-B.

Tracking Mode: On, Off.

Tally Mode: On, Off.

4.8 COMMUNICATION SETUP

Move the main menu cursor to [COMMUNICATION SETUP], and press [HOME] key enter the

communication setup page, as shown in the following figure.

COMMUNICATION SETUP

Protocol

VISCA

V_Address

V_AddrFix

Off

Net Mode

Serial

Baudrate

9600

Select Item

Change Value

[Menu] Back

Protocol: Control protocol type, Auto, VISCA, PELCO-D, PELCO-P.

V_Address: 1 ~ 7. (Effective only in Auto, VISCA protocol).

V_AddrFix: On, Off (When set to On, useless in 88 30 01 FF Command).

P_D_Address: 0 ~ 254. (Effective only in PELCO-D protocol).

P_P_Address: 0 ~ 31. (Effective only in PELCO-P protocol).

Net Mode: Set the serial port network control, Serial, Paral.

Baudrate: Serial port baud rate, 2400, 4800, 9600, 38400.

4.9 RESTORE DEFAULT

Move the main menu cursor to [RESTORE DEFAULT], and press [HOME] key enter the restore default page,

as shown in the following figure.

RESTORE DEFAULT

Restore?

Change Value

[Home] OK

[Menu] Back

Restore: Confirm restore factory settings, Yes, No.

Note: Press [HOME] button to confirm, all parameter restore default, include IR Remote address and VISICA

address.

Altri manuali per TeamUp TX20i

Indice

Altri manuali CAVE Macchina fotografica digitale

CAVE

CAVE TeamUp A01 Manuale utente

Manuali Macchina fotografica digitale popolari di altre marche

Mercury

Mercury 350K Manuale utente

Pentax

Pentax Optio LS 465 Manuale utente

Sanyo

Sanyo VPC-S1085 Manuale utente

GE SMART A1255 Manuale utente

Point Grey

Point Grey Gazelle Manuale utente

Nikon

Nikon COOLPIX A Manuale utente

Pentax

Pentax P-5 Manuale utente

BlazeVideo

BlazeVideo A280 Manuale utente

Sony

Sony MCA-20 Manuale utente

Sony

Sony Alpha DSLR-A290 Manuale utente

ATIK Cameras

ATIK Cameras One Manuale utente

CohuHD Costar

CohuHD Costar 3930 Series Manuale utente

Leica

Leica M10-R Manuale utente

FujiFilm

FujiFilm FinePix A700 Manuale utente

Lorex

Lorex LNZ81P25 Series Manuale utente

GE J1470S Manuale utente

Sony

Sony A6700 Guida utente

Canon

Canon EOS ELAN7 Manuale utente