Cavecool CC34SB Manuale utente
Service Manual for Cavecool
Single zone model#CC34SB&CC62SB&CC102SB
Dual one model#CC29DB&CC54DB&CC102DB
CC34SB CC62SB CC102SB
CC29DB CC54DB CC102DB
The following lists the bar in the course of various failures that may occur,aswellastofindandfix
these faults. Please corresponds fault item and then find the corresponding page number information.
Maintenance Preparing:
○Tools
1．Vise 2．Cross screwdriver 3．goggles 4．Clamp Meter 5. Multimeter
(5A)
5．
Wrench 6．
Electric iron 7．
Strippers 8．Sealing jaws 10. The protective gloves
○ Equipment
1．Vacuum p um p 2．Soldering equipment 3. Pressure gauge / refrigerant metering device
Content
1.Precautions………………………………………………………………4
2.Technical specification………………………………………………5
2.Schematic diagram……………………………………………………6
3. NTC value…………………………………………………………………8
4.Control panel……………………………………………………………10
5.The fault diagnosis……………………………………………………11
6.Disassembly instruction of main components………………17
4
1. Repair work safety precautions (please follow below precautions before maintenance)
DANGER
• Do not use open flames indoor or smoke during reqairing.
• Do not perform welding in poorly ventilated and confined areas
• Do not have children nearby when reparing
WA R N I N G
•Always unplug the power cord first before carrying out maintenance
Otherwise, it may result in electric shock and injuries.
•Please be careful not to get electric shock during reparing.
Unplug the power cord before maintenance. If needs to check the circuit while the
power is on,do not touch the live electrical parts! If electric wires are damaged, it
must be replaced by qualified technician in time.
• Use original parts which shown in the part list, do not use parts from other models
or other brands, never modify the parts
• Use appropriate maintenance tools, improper use of tools may cause insecure
assembly
• If wires are cut during maintenance. Remember to reconnect the wire and seal with
insulating tape
•When discharging the refrigerant, make sure the room is in good ventilation
condition.
•When cutting off the compressor pipes, pay attention to the remaining refrigerant
and internal pressure.
• After maintenance finished, use multimeter to check the insulation, makesurethe
insulation resistance is over 2 MΩ before connecting to power.
•After repair, it is necessary to check whether the grounding is in good condition
5
NOTICE
Be careful to the high temperature of compressor and refrigeration pipes when
product is on or just after the production was power off.
Be careful to the high temperature after soldering
Be careful not to let liquid refrigerant directly touches the skin,it may cause
frostbit
Metal parts and plastic parts burr may scratch the hand.
1.
Technical specification
Single zone model
Model no. CC34SB CC62SB CC102SB
Product type
Single zone compressor
wine cooler
Single zone compressor
wine cooler
Single zone compressor
wine cooler
Installation Type Free standing only Free standing only Free standing only
Gross / Net Volume 91L / 89L 152L / 148L 247L / 242L
Bottle Loading Capacity 34 bordeaux bottles 62 bordeaux bottles 121 bordeaux bottles
Voltage
&Frequency
220‐240V / 50Hz 220‐240V / 50Hz 220‐240V / 50Hz
Power 90W 90W 100W
Set temperature 5℃～20℃5℃～20℃5℃～20℃
Gas refrigerant R600a R600a R600a
Weight of gas 25g 30g 38g
Defrosting type Auto defrost Auto defrost Auto defrost
Climate class SN/N/ST SN/N/ST/T SN/N/ST/T
Product dimension
(W*D*H ) 480×430×508 480×565×850 550×565×1277
6
Dual zone model:
2.
Schematic diagram
2.1.Single zone model
Model no. CC29DB CC54DB CC102DB
Product name
Dual zone compressor
wine cooler
Dual zone compressor
wine cooler
Dual zone compressor
wine cooler
Installation Type Free standing only Free standing only Free standing only
Gross / Net Volume 85L / 80L 142L / 138L 240L / 232L
Bottle Loading Capacity 34 bordeaux bottles 62 bordeaux bottles 102 bordeaux bottles
Voltage
&Frequency
220‐240V / 50Hz 220‐240V / 50Hz 220‐240V / 50Hz
Power 90W 90W 100W
Temperature
Setting
Upper: 5℃～12℃
Lower:12℃～18℃
Upper: 5℃～12℃
Lower:12℃～18℃
Upper: 5℃～12℃
Lower:12℃～18℃
Gas refrigerant R600a R600a R600a
Weight of gas 22g 22g 22g
Defrosting type Auto defrost Auto defrost Auto defrost
Climate class N/ST SN/N/ST SN/N/ST
Product dimension
(W*D*H ) 480×430×508 480×565×850 550×565×1277
7
2.2 Dual zone model
、
3. Cooling system schematic diagram:
3.Cooling system schematic diagram:
2.3 Cooling system schematic diagram:
8
3.NTC value
9
4.Structure diagram
4.1 Single zone model
4.2 Dual zone model
1Fan
2Control panel and LED light
3Shelf
4Feet
5Lower hinge
6Door
7Gasket
8Upper hinge
1Fan
2LED light
3Shelf
4Control panel
5Feet
6Lower hinge
7Door
8Gasket
9Upper hinge
10
5.Control Panel
5.1 Single zone model
13
24
Temperature range is 5‐20°C.
‐ 1. Press ON/OFF button to turn on the appliance, and press ON/OFF for 3 seconds to turn off the appliance.
‐ 2. Press LIGHT button to turn on or turn off the light
‐3.Press UP button to increase the setting temepreture
‐4.Press down button to decrease the setting temepreture
Press temperature control button “UP” and “DOWN” together for 3 seconds to change the LED display from
Celsius to Fahrenheit
Important note: After selecting the desired temperature, the display will continue to show the real
temperature inside the equipment, which will vary gradually until it reaches the selected temperature.
5.2 Dual zone model
Temperature range for upper zone is 5‐12°Candforlowerzone
is
12‐18°C.
-Press power switch button for 3 seconds to turn on or turn off the appliance
-Press light button to turn on or turn off the light in both zones
Questo manuale è adatto per i seguenti modelli
5
Indice
