celios G200 Manuale utente
G200
Advanced Air Purier
Quick Start
2
STEP 1: INSTALLING THE
AIR FILTERS
Installing the Core Filter
The G200 uses three powerful air lters. All are
colored blue for easy identication.
1. Slide the Core Filter into the G200 Core with
the grill facing up.
2. The filter clicks into place when properly
installed.
1
1. Turn the G200 Core over so the Celios logo is
facing down. Remove the back panel at the
bottom of the unit.
2. Slide the Pre Filter into place with the arrows
pointing toward the top of the Core. Make sure
to push the Pre Filter completely into the Core
so that the back panel can fully close.
Installing the Pre Filter
1
2
1. Remove the Carbon Filter tray from the Main
Stand.
2. Place the Carbon Filter into the tray as shown.
3. Slide the tray back into position in the G200
Main Stand. The tray clicks into place when
properly installed.
Installing the Carbon Filter
2
3
1
STEP 2: INSTALLING THE LITHIUM
ION SMART BATTERIES
The G200 runs on either outlet power or Lithium
Ion Smart Batteries, which are included with your
G200 purchase. These batteries are hot swappable,
which means you can remove either of them
without shutting down the G200 or interrupting air
purication.
Note: you can run the
G200 without batteries by
plugging the main stand
or Core into a powered
electrical outlet.
1. There are two slots for the Lithium Ion Smart
Batteries above the Pre Filter you just installed.
Pull the silver wire and rotate it upwards.
2. Take one Lithium Ion Smart Battery and align
the battery slots to the slots within the unit. The
unit will beep when the first battery is correctly
installed.
3. Take the second battery and do the same.
Note you will not hear a beep with the second
battery. When installed properly the Celios
logo on the batteries will be as pictured in the
illustration.
4. Place the silver wire back into position and
replace the back cover onto the G200 Core unit.
Installing the Lithium Ion Smart Batteries
1
2
1. Plug the Power Adapter into the Main Stand and
then to a powered electrical outlet.
2. Slide the G200 Core into the Main Stand. The
control panel on the Core will be facing to the
same side as the Remote.
3. When you correctly dock the G200 Core in the
Main Stand, the unit will beep (whether you
have AC power or not). If the G200 Core is not
properly installed, it will not beep and will not sit
properly within the Main Stand.
Dock the G200 Core in the Main Stand
2 3
1. After turning on the G200 Core, the battery
life indicator on the control panel shows
that the batteries are charging. When the
batteries are fully charged or when there are
no batteries in the G200 Core, the battery life
indicator light will turn off.
2. You can also charge the batteries outside of
the Main Stand by plugging the Power Adapter
directly into the G200 Core.
Charging the batteries
Charging the batteries the rst time
1. After inserting the batteries, connect the Core
with the supplied power adapter. The Core
can be docked in the Main Stand or plugged in
directly.
2. Allow the batteries to charge until full .
You may run the G200 on any setting while
charging.
3. Turn the unit on to Speed 1 and remove the
power adapter plug.
4. Allow the unit to fully discharge and power off.
This operation can take up to 30 hours.
5. Fully charge the unit again per Steps 1 and 2
above. The batteries are now properly charged
for maximum performance.
Properly charging the batteries will allow maximum
runtime and battery life. The following procedure
should be followed on the rst charge of any new
batteries.
This procedure can be repeated if the battery life
is lower than expected. If this procedure fails to
increase battery life, contact Customer Care at
1-833-CELIOS1 or customer[email protected].
STEP 3: SETTING UP
THE REMOTE CONTROL
1. Install the provided two AAA
batteries into the Remote
Control.
2. With the G200 powered on, press
and hold the Core power button
for 6 seconds. The Core will beep
and its power button will begin
to flash, indicating that it has
entered Bluetooth pairing mode.
3. While the Core is in pairing mode,
turn on the Remote Control by
pressing its power button. The
light on the Remote will flash
briefly, indicating that it has also
entered Bluetooth pairing mode.
4. After 6 seconds, both the Core
and the Remote Control light will
stop flashing. The two are now
paired.
The G200 uses a Bluetooth remote control
device, which can work within a 75 ft range. When
not in use, store the remote control in the slot on
the front of the G200 Main Stand.
Pair the Remote Control with the G200 Core
Note: If the Remote
Control is not paired
properly, the light
will blink.
Altri manuali per G200
1
Indice
Altri manuali celios Purificatore d'aria
