Cembre TND6-70 Manuale utente

MECHANICAL CRIMPING TOOL

TND6-70 TNH6-70

ENGLISH OPERATION AND MAINTENANCE MANUAL

20 M 135 E

1. GENERAL CHARACTERISTICS

Application range:

TNH6-70

TND6-70

- Copper tube terminal lugs type HR.. for conductor sizes

6mm

to 70mm

- Copper tube splices type HSV.. for conductor sizes 6mm

70mm

- Copper tube terminal lugs according to DIN46235 (Cembre

type DR..) for sizes

6mm

to 70mm

- Copper tube splices according to DIN46267 Part 1 (Cembre

type DSV..) for sizes

6mm

to 70mm

Weight kg (lbs) 2,1 (4.6)

Dimensions: mm (inches)

length 515 (20.2)

width 132 (5.2)

2.1) Operator information:

- The instructions within this operation and maintenance manual should always be followed.

- The tool should only be used by competent personnel who are familiar with the instructions

contained within this manual.

2.2) Application:

Not to be used for any other purpose than for which the tools were designed

Do not use these crimping tools to crimp other type of lugs or connectors.

2. INSTRUCTIONS FOR USE

2.3) Die proﬁle selection:

- Fully open the tool handles

- Press down the locking-pin of the indexable die plates.

- TNH6-70: Rotate the die proﬁles until the stamped cross section matches the cross section on

the cable lug/connector.

- TND6-70: Rotate the die proﬁles until the 'K' number matches the equivalent No. marked on

the palm of the terminal lug or the wall of the splice.

- Release the locking-pin until the die proﬁle is ﬁxed.

- Adjust the second die proﬁle in the same manner as the ﬁrst by following the above instruc-

tions. Both proﬁle dies must have the same 'K' number.

Incorrect choice of die proﬁle will result in tool damage and/or aﬀect the quality of the

crimped joint, leading to potential failure

2.4) Cable preparation:

- Cut the cable perpendicular to the central axis.

- Neatly strip the insulation over a distance equal to the barrel length allowing an additional

10%. Ensure all traces of the insulation are removed. Avoid damage to the outer layer of con

ductor strands.

- Clean the conductor carefully.

- Sector-shaped conductors must be pre-rounded

before crimping.

2.5) Crimping procedure:

Open the crimping tool handles and position the

connector at the lower part of the die proﬁle (see

image). The terminal lug/splice axis should be per-

pendicular to the plane of the die proﬁle

- Apply a small pressure to the handles to close the dies suﬃcient to trap the connector

- Fully insert the conductor into the connector barrel.

- Apply suﬃcient force to close the handles and cause the dies to compress the connector and

conductor until the die proﬁles become in contact.

- Apply the correct number of compressions as deﬁned on page 4, in the direction deﬁned in

the ﬁgure below.

- The crimping bite width is 5mm for these tools.

Arbeitsrichtung beim Verpressen

DIRECTION OF THE COMPRESSIONS

Connector

3. MAINTENANCE

Copper

cross-section

mm2

TNH6-70

6 1x 1+1

10 1x 1+1

16 1x 1+1

25 2x 2+2

35 2x 2+2

50 2x 2+2

70 2x 2+2

Identiﬁcation

Number

Copper

Cross-section

mm2

TND6-70

5 6 1x 1+1

6 10 1x 1+1

8 16 2x 2+2

10 25 2x 2+2

12 35 2x 2+2

14 50 3x 3+3

16 70 3x 3+3

2.6) Number of compressions required:

- The table below shows the number of compressions required per conductor size.

- If only one compression is required, please position the crimp at the midpoint of the connec-

tor barrel. If several compressions are required these should be spaced evenly.

- Remove dust, humidity and other impurities with a clean brush or a soft cotton-free cloth.

Never use any items which may damage the tool.

- Take care that the bolts, any moveable parts and the tool surface are coated with a thin ﬁlm of

high quality oil.

- Ensure die proﬁles can be rotated freely prior to use

- Store the tool in a dry and clean area.

3.1) Safety advice:

- Ensure hands are free of the crimping area at all times

- Ensure that the dies are completely closed to obtain a full compression

Never work with energised conductors. Ensure that voltage has been switched oﬀ before

starting work and check this with adequate instruments.

- Alteration of the tool is prohibited.

- Before operating the tool, check for any damage, the tool should not be used if damage is

visible

- The tool should be returned to the nearest Cembre service centre for any repairs required.

PROBLEM: CAUSE: SOLUTION:

Excess ﬂash (wings) on

the crimped joint

- A smaller die proﬁle than required has

been selected.

- Incorrect connectors have been used

- Other causes

- Adjust die proﬁles to match the

connector requirement

- Verify the connector type and size

is correct

- Return tool to Cembre for inspec-

tion and repair

The compression is of

insuﬃcient depth and

the conductor can be

pulled from the joint

- The die proﬁle is larger than required

- Incorrect connectors type have been

used

- Other causes

Die proﬁle cannot be

changed - Locking bolt has snapped in - Press down locking bolt

Proﬁle dies are diﬃcult

to rotate

- Tool is soiled

- Tool is insuﬃcient oiled

- Clean the tool

- Oil the bolts and screws

- Return tool to Cembre for inspec

tion and repair

Tool has no tension

when handles are fully

closed

- Tool is worn - Return the tool to Cembre for

inspection and repair

4. TROUBLESHOOTING

5. PARTS LIST (Ref. to Fig. 1)

Code Item DESCRIPTION Qty

6950043 01 PROFILE DIE (TNH) 9996301 2

6950041 01 PROFILE DIE RIGHT (TND) 9018201 1

9018102 02 PLATE BAR 1 2

9018103 03 PLATE BAR 2 2

9018104 04 TOGGLE 1 1

9018105 05 TOGGLE 2 1

6950045 06 LOCKING BOLT 9018106 2

6950046 07 COMPRESSION SPRING, CONICAL 9018107 2

9018108 08 TUBE 1

9018109 09 BAR, WITH TOOL-NO. (TNH) 1

9018209 09 BAR, WITH TOOL-NO. (TND) 1

9018209L 10 BAR, WITH COMPANY LOGO 1

9018111 12 SPIRAL PIN 5X14 4

9018112 13 FILLISTER HEAD SCREW M 6X20, ZINC PLATED 1

9018113 14 FILLISTER HEAD SCREW M 6X25, ZINC PLATED 2

9018114 15 FILLISTER HEAD SCREW M 6X30, ZINC PLATED 2

9018115 16 NUT, SELF-LOCKING M6 4

9018116 17 WASHER 6,4, ZINC PLATED 8

9018117 18 GUIDE SLEEVE 1 1

9018118 19 GUIDE SLEEVE 2 2

9018119 20 GUIDE SLEEVE 3 2

9018120 21 DISTANCE SLEEVE 4

9018121 22 GRIP 2

6950044 23 CIRCLIP 12X1 9065207 4

6950042 24 PROFILE DIE LEFT (TND) 9018222 1

The guarantee is void if parts used are not Cembre original spares.

When ordering spare parts always specify the following:

- code number of item

- name of item

- type of tool

FIG. 1

This manual is the property of Cembre: any reproduction is forbidden without written permission.

www.cembre.com

Cembre Ltd.

Dunton Park

Kingsbury Road, Curdworth - Sutton Coldﬁeld

West Midlands B76 9EB (UK)

Tel.: +44 01675 470440 - Fax: +44 01675 470220

E-mail: [email protected]

www.cembre.co.uk

Cembre S.a.r.l.

22 Avenue Ferdinand de Lesseps

91420 Morangis (France)

Tél.: +33 01 60 49 11 90 - Fax: +33 01 60 49 29 10

CS 92014 - 91423 Morangis Cédex

E-mail: [email protected]

www.cembre.fr

Cembre España S.L.U.

Calle Verano 6 y 8

28850 Torrejón de Ardoz - Madrid (España)

Teléfono: +34 91 4852580

Telefax: +34 91 4852581

E-mail: [email protected]

www.cembre.es

Cembre GmbH

Heidemannstraße 166

80939 München (Deutschland)

Telefon: +49 89 3580676

E-mail: [email protected]

www.cembre.de

Cembre Inc.

Raritan Center Business Park

300 Columbus Circle - Suite F

Edison, New Jersey 08837 (USA)

Tel.: +1 732 225-7415 - Fax: +1 732 225-7414

E-mail: [email protected]

www.cembreinc.com

Cembre S.p.A.

Via Serenissima, 9

25135 Brescia (Italia)

Telefono: +39 030 36921

Telefax: +39 030 3365766

E-mail: [email protected]

www.cembre.com

Cembre GmbH (Betriebsstätte Weinstadt)

Boschstraße 7

71384 Weinstadt (Deutschland)

Telefon: +49 7151 20536 - 60

E-mail: [email protected]

www.cembre.de

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Cembre Utensili elettrici

Cembre

Cembre ECW-H3D Manuale utente

Cembre

Cembre PNB-3 Series Manuale utente

Cembre

Cembre B1500 Manuale di istruzioni

Cembre

Cembre RHU 1000 Manuale del proprietario

Cembre

Cembre B62 Istruzioni operative

Cembre

Cembre PNB-7KE Manuale utente

Cembre

Cembre RHU450 Manuale utente

Cembre

Cembre B125LN-C Manuale utente

Cembre

Cembre MTE1-S Manuale utente

Cembre

Cembre B600 Manuale utente

Cembre

Cembre RHU520 Manuale utente

Cembre

Cembre B-TD270 Manuale utente

Cembre

Cembre B1350-C-KV Guida all'installazione

Cembre

Cembre B500ND Manuale utente

Cembre

Cembre BTEPE2.DET12 Manuale utente

Cembre

Cembre B600CND Manuale utente

Cembre

Cembre RH50 Manuale utente

Cembre

Cembre B600 Manuale utente

Cembre

Cembre HT131-C Manuale utente

Cembre

Cembre B15D Manuale utente

Cembre

Cembre B-TC950A Manuale utente

Cembre

Cembre B500 Manuale utente

Cembre

Cembre B54MD-D6 Manuale utente

Cembre

Cembre B-FL750 Manuale utente

Manuali Utensili elettrici popolari di altre marche

AEG

AEG OMNI-JS Manuale utente

SIP

SIP 01533 Manuale utente

Ribimex

Ribimex PRS499 Manuale utente

3M Fiber Optic Connector Crimp Tool Manuale utente

Ryobi

Ryobi P524 Manuale utente

ROJEK

ROJEK FSN 300A Manuale utente

Kemper

Kemper 1740PRO Manuale utente

WABCO

WABCO OptiTire Manuale utente

EINHELL

EINHELL TE-MS 18/210 Li Manuale utente

Orgapack

Orgapack OR-T 85 Guida rapida

TOUGHCUT

TOUGHCUT Diamond 400 Manuale utente

Yaros

Yaros PB-3603 Manuale utente

Fein

Fein BSS 2.0 E Guida all'installazione

Baileigh Industrial

Baileigh Industrial SS-2725 Manuale utente

Milwaukee

Milwaukee 2674-20 Manuale utente

Fein

Fein BLs 1.6 Manuale utente

Princess

Princess Electric Multi Sharpener Manuale utente

FOREDOM

FOREDOM K.1050 Manuale