Cen-Tec CT23QD Manuale utente
CT23QD Electric Brush Manual
™
CT23QD Electric Brush Manual
LIMITED WARRANTY
Subject to the conditions and exceptions stated in this
warranty Cen-Tec Systems warrants the products sold by
Cen-Tec Systems to be free from defects in materials and
workmanship under normal residential use and service for
two (2) years from the date of delivery on presentation of the
original contract or invoice. A copy of the original bill of sale
must accompany all warranty requests. If one is not produced
as required the manufactures date code will be used.
CONTACT INFORMATION
1807 Morrissey Drive
Bloomington, Illinois 61704
PHONE: (309) 664-0328
TOLL FREE: (800) 833-2822
FAX: (309 663-8766
EMAIL: help@centecsystems.com
WEBSITE: www.centecsystems.com
www.centeccommercial.com
©Cen-Tec Systems Inc 2015
Safety instructions
!WARNING Electric shock could
occur if used out doors
or on wet surfaces.
Please read all instructions before using this Electric Powerhead.
Save these instructions. INTENDED FOR HOUSEHOLD USE ONLY.
1) Unplug and disconnect power before servicing.
2) Always turn o this appliance before connecting
or disconnecting either hose or motorized
nozzle.
3) Do not pick up anything that is burning or
smoking, such as cigarettes, matches or hot
ashes.
4) Use only as described in this manual. Use only
manufacturers recommended attachments.
5) Do not unplug by pulling on cord. To unplug,
grasp the plug, not the cord.
6) Do not handle system of appliances with wet
hands.
7) Turn o all controls before unplugging.
8) Do not use with damaged cord or plug. If
appliance is not working as it should, has been
dropped, damaged, left outdoors, or dropped
into water, return it to distributor.
9) Do not allow to be used as a toy. Close attention
is necessary when used by or near small
children.
10) The hose contains electrical wires. Do not use if
damaged, cut or punctured. Avoid picking up
sharp objects.
11) Do not put any object into openings.
12) Do not use with any opening blocked; keep free
of dust, lint, hair, and anything that may reduce
air ow.
13) Keep hair, loose clothing, ngers, and all parts
of the body away from openings and moving
parts.
14) Do not leave vacuum or brush when plugged in.
Unplug from outlet when not in use and before
servicing.
15) Do not pick up ammable or combustible
liquids such as gasoline or use it in areas where
they may be present.
16) Use extra care when cleaning on stairs.
CT22QD
Premium Electric Power Brush
This power brush is used to vacuum
carpets. It has a 14” edge to edge
brushed head to create a wider
cleaning path. It is to be used with the
integrated telescopic wand.
Features include:
Quietdrive™• - Multi-grooved rein-
forced belt for continuous contact and
ecient transfer of power to the brush.
Quick Wand Release• - For an easy
switch from carpet to hard oor, edge
cleaning or above oor cleaning.
4 Level Height Adjustment• - Adjusts
to match surface being cleaned.
Soft Bumper• - Wraps around brush
to protect baseboards and furniture.
Headlight• - For lighting your clean-
ing path.
Active Brush Edge Cleaner• - Guide
either side of the brush along base
boards or next to furniture to help
remove dirt trapped at carpet edges.
Cen-Tec CT23QD
Electric Brush Parts Explosion
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
30
32
33
34
35
36
37
CENTEC Part # Object Description
38672
38683
38694
38705
38716
38727
38738
56306
38749
38760
40383
37308
38771
38782
40933
40625
38793
38804
38815
41120
37330
37341
40317
40944
56058
37319
40284
40999
38826
38837
38848
38859
37176
37187
40427
FLOOR NOZZLE UPPER
BUTTON (EXTENSION) (DECO)
WINDOW COVER (HEIGHT ADJ.)
FURNITURE GUARD
VALVE B (SUCTION CONTROL -N.B.S.)
VALVE A (SUCTION CONTROL B.S.)
FLOOR NOZZLE COVER (W/ LENS) (DECO)
SERVICE, SCREW
CONNECTION PIPE ASSEMBLY (NOZZLE) PC
FOOTPEDAL Q.R.
SWIVEL SEAL (2)
SERVICE, SCREW, PAN HD #8 - 18 X 35MM (CENTEC)
SWIVEL CAP
PEDAL / HANDLE RELEASE
INDICATOR BLOCK ASSY
LIFTER
FILTER - INTAKE/EXHAUST
WIRE CONNECTOR
OVERLOAD PROTECTOR (KUOYUH 2.5)
LEAD WIRE UNIT
SERVICE, BULB SOCKET (CENTEC)
SERVICE, BULB LIGHT (CENTEC)
MOTOR BRIDGE
SERVECE, SCREW #8 - 18 X 5/8 (CENTEC)
MOTOR GASKET
SERVICE, MOTOR ASSEMBLY (CENTEC)
SERVICE, MOTOR ADJUSTMENT SPRING (CENTEC)
BELT
SCR THRCUT PAN 8 - 18 X 1 7/8
AGITATOR UNIT
BRUSH COVER
FLOOR NOZZLE LOWER
SERVICE, NOZZLE ROLLER (CENTEC)
SERVICE, ROLLER SHAFT (CENTEC)
FRONT AXLE ASSY
Cen-Tec CT23QD
Electric Brush Parts Explosion Vacuuming tips
Suggested Sweeping Pattern
For best cleaning action, the powerhead should
be pushed straight away from you and pulled
straight back. At the end of each pull stroke, the
direction of the powerhead should be changed
to point into the next section to be cleaned.
This pattern should be continued across the
carpet or oor with slow, gliding motions.
NOTE: Fast
random strokes
do not provide
complete
cleaning.
!CAUTION
Product Damage Hazard
Use care if the powerhead and wand are left
in the upright position as they may tip over
easily. Property damage can occur if tipped.
!WARNING
Personal Injury and Product Damage Hazard
DO NOT run over power cord with the•
powerhead. Personal injury or product
damage could result.
DO NOT pull plug from wall by the•
power cord. If there is damage to the cord
or plug, personal injury or property damage
could result.
Powerhead Steering
The nozzle swivel rotates left and right for
improved maneuvering in tight spaces and
around corners.
Wand Upright
Locked Position
When the wand is returned
to the upright position, the
wand rotation lock holds the
wand in place. This prevents
rotation of wand and hose
handle for better stability.
Under Furniture
To maximize the reach of the powerhead
under furniture, turn the handle to either side
and lower the wand close to the oor.
Belt Reset
The powerhead has built-in protection against
motor and belt damage should the agitator
jam. If the agitator slows down or stops, the
belt reset shuts o the powerhead and the red
belt reset light will turn on.
Belt Reset Button
To correct problem: Turn o and unplug the
powerhead, remove obstruction, then press
belt reset button. If the problem persists, have
the powerhead serviced by a Sears or other
qualied service agent.
Belt & Agitator Changing/Replacement Agitator Cleaning
To Clean Agitator
NOTE: In order to keep cleaning
eciency high and to prevent
damage to your powerhead, the
agitator must be cleaned every time
the belt is changed. The agitator
must also be cleaned according to
the following schedule.
Vacuum Cleaner Use
HEAVY -
(Used daily)
MODERATE -
(Used 2-3 times/week)
LIGHT -
(Used 1 time/week)
Clean Agitator
every week
every month
every 2 months
IMPORTANT
Disconnect powerhead from electrical outlet. Check and remove hair, string
and lint build-up frequently in the powerhead agitator and end cap areas.
Remove any dirt or debris in the belt path area or in the brush roller area.
Carefully remove string or debris located on the agitator or end caps.
1) Turn the nozzle upside
down and unscrew the screws
located below.
Agitator Assembly
To Replace Belt
To Replace Agitator
2) Locate and pull the tabs
shown below on the back of
the nozzle.
3) Take the black top casing o
of the nozzle.
4) Remove the clear plastic
covering over the agitator.
5) Lift both sides of the agitator
out of the holding slots and
pull it through the belt loop.
After removing the agitator
you can remove the belt from
the motor.
To Replace Light Bulb
After taking o the black top
casing locate the light bulb
and pull it out, then simply
push the new bulb in.
End Cap
Belt Path
End Cap
Brush Unit
Indice
Altri manuali Cen-Tec Pulitore a vapore
