Central Pneumatic 00422 Manuale utente

AIRPAINTSHAKER

ASSEMBLYandOPERATINGINSTRUCTIONS

3491 Mission Oaks Blvd. / Camarillo, CA93011

No portion of this manual or any artwork contained herein may be reproduced in any

shape or form without the express written consent of Harbor Freight Tools.

For technical questions and replacement parts, please call 1-800-444-3353.

SPECIFICATIONS

Capacity 1 gallon to 1 quart can, up to 16lbs. Gross weight.

Speed Up to 700 cycles per minute @ 30° shake angle.

Air Pressure 70 to 175 PSI

Air Consumption 4.3 CFM with 1 gallon can/16 lbs.

SAVE THIS MANUAL

You will need the manual for the safety warnings and cautions, assembly instructions, operating

procedures, maintenance procedures, trouble shooting, parts list, and diagram. Keep your

invoice with this manual. Write the invoice number on the inside of the front cover. Keep both

this manual and your invoice in a safe, dry place for future reference.

SAFETY WARNING & CAUTIONS

WARNING: When using pneumatic equipment, basic safety precautions should always be

followed to reduce the risk of personal injury and hazards due to over pressurization.

READ ALL INSTRUCTIONS BEFORE USING THIS TOOL!

1. KEEP WORK AREA CLEAN. Cluttered areas invite injuries.

2. OBSERVE WORK AREA CONDITIONS. Do not use tools in damp, wet, or poorly lit

locations. Don’t expose to rain. Keep work area well lit. Do not use electrically powered air

compressors in the presence of flammable gases or liquids.

3. KEEP CHILDREN AWAY. Children must never be allowed in the work area. Do not let them

handle machines, tools, or hoses.

4. STORE IDLE EQUIPMENT. When not in use, tools must be locked up in a dry location to

inhibit rust.Always lock up tools and keep out of reach of children.

5. DO NOT FORCE THE TOOL. It will do the job better and more safely at the rate for which

it was intended. Do not use inappropriate attachments in an attempt to exceed the tool’s

capacities.

6. USE THE RIGHT TOOL FOR THE JOB. Do not attempt to force a small tool or

attachment to do the work of a larger industrial tool. Do not use a tool for a purpose for

which it was not intended.

7. DRESS PROPERLY. Do not wear loose clothing or jewelry as they can be caught in

moving parts. Non-skid footwear is recommended. Wear restrictive hair covering to contain

longhair.

Page #2 -- SKU: 00422 REV 10/06

8. USE EYE AND EAR PROTECTION. Always wear ANSI approved chemical splash/impact

goggles when working with paint and chemicals. Wear and ANSI approved dust mask or

respirator for the type of paint or stain you are working with.

9. DO NOT ABUSE THE POWER CORD. Do not yank compressor’s cord to disconnect it

from the receptacle. Do not carry tools by the cord.

10. DO NOT OVERREACH. Keep proper footing and balance at all times. Do not reach over

or across running machines.

11. MAINTAIN TOOLS WITH CARE. Keep tools clean for better and safer performance.

Follow instructions for lubricating and changing accessories. Inspect compressor’s cord

periodically and, if damaged, have them repaired by an authorized technician. Inspect all

hoses for leaks prior to use. The handles must be kept clean, dry, and free from oil and

grease at all times.

12. REMOVE ADJUSTING KEYS AND WRENCHES. Make it a habit to check that keys and

adjusting wrenches are removed from the tool or machine work surface before attaching air

hose.

13. AVOID UNINTENTIONAL STARTING. Do not carry any tool with your finger on the trigger,

whether it is connected to the compressor or not.

14. STAY ALERT. Watch what you are doing, use common sense. Do not operate any tool

when you are tired.

15. CHECK DAMAGED PARTS. Before using any tool, any part that appears damaged should

be carefully checked to determine that it will operate properly and perform its intended

function. Check for alignment and binding of moving parts; any broken parts or mounting

fixtures; and any other condition that may affect proper operation.Any part that is damaged

should be properly repaired or replaced by a qualified technician. Do not use the tool if any

switch does not turn on and off properly.

16. REPLACEMENT PARTS AND ACCESSORIES. When servicing, use only identical

replacement parts. Use of any other parts will void the warranty. Only use accessories

intended for use with this tool.Approved accessories are available from Harbor Freight

Tools.

17. DO NOT OPERATE TOOL IF UNDER THE INFLUENCE OF ALCOHOL OR DRUGS.

Read warning labels on prescriptions to determine if your judgment or reflexes are impaired

while taking drugs. If there is any doubt, do not operate the tool.

18. DRAIN COMPRESSOR EVERY DAY. Do not allow moisture to build up inside the

compressor. Do not allow compressor to sit pressurized for longer than one hour.

19. MAKE SURE ALL EQUIPMENT IS RATED TO THE APPROPRIATE CAPACITY. Make

sure that regulator is set at least 10 PSI lower than the lowest rated piece of equipment you

are using.

Page #3 -- SKU: 00422

GENERAL

Your Paint Shaker is a very useful air tool. It has the capacity to shake a single pint can, four 1

liter round cans, most aerosols (with caps) and square gallons. Your Paint Shaker can also

take 1/4 and 1/2 pints stacked, or singly with spacers.

UNPACKING

When unpacking, check to make sure the following parts are included. All sizes listed below are

approximate. If any parts are missing or broken, please call Harbor Freight Tools at the number

on the cover of this manual.

ITEM# DESCRIPTION

N/A Paint Shaker

#01 Control Valve

#02 Brass Nipple

#03 Lubricator Assembly

#04 Inlet Fitting

ASSEMBLY

Step1: Select a clear area on your workbench to mount the Paint Shaker. Use the appropriate

hardware. Make sure Paint Shaker is securely mounted.

Step 2: Thread the INLET FITTING (#04) into the HOUSING ASSEMBLY (#40) and tighten

with a 5/8" wrench.

Step 3: Thread the LUBRICATOR ASSEMBLY (#03) onto the INLET FITTING. Do not over

tighten.

Step 4: Thread the CONTROL VALVE (#01) onto the BRASS NIPPLE (#02), already fitted to

the LUBRICATOR ASSEMBLY. Tighten with a 5/8" wrench.

Step 5: Your Paint Shaker is ready for use.

NOTE

The Recommended Oil for this air

tool is 5W to 10W Non-detergent

Rust Inhibiting Air Tool Oil. DO NOT

USE MOTOR OIL.

CAUTION

Do not shake aerosols for more than one

minute. Do not shake aerosols if can

temperature is over 100oF.

Page #4 -- SKU: 00422

OPERATION

Step1: Clamp can firmly by turning the HANDLE (#44) as

shown in Figure 1. Do not crush can.

Handle (#44)

Tighten

djustment Screw (#07)

NOTE

Clamp mostly empty cans and

aerosol cans with lids toward

clamp handle.

CAUTION

Watch cans while shaking. Make sure

cans do not come loose. Turn Paint

Shaker off immediately if this happens.

Figure 1 — Clamping Paint Can

Step2: SetAir Compressor’s regulator for 120 PSI and turn on.

Step3: Allow pressure to build to 120 PSI.

Step4: Start Paint Shaker by quickly opening the control valve about 1/4 turn.

Step5: Stop Paint Shaker when done by closing the control valve.

Step 6: Unclamp can. Remove.

Step7: If rotation is more/less than 15° from side-to-side, screw the ADJUSTMENT

SCREW (#07) in/out respectively.

Page #5 -- SKU: 00422

MAINTENANCE

Your air tool needs regular maintenance, including checking the oil level, checking the shake

angle, and grease the clamp screw and zerk fittings.

Adjust Lubricator

Check oiling each time you stop the Paint Shaker.

Step 1: Remove the Fill Cap from the LUBRICATOR ASSEMBLY (#03) and fill the Oil

Reservoir with Pneumatic Oil.

Step2: Open (by turning counterclockwise) or close (by turning clockwise) Oil Drip Rate

Adjustment Screw, located on top of the LUBRICATOR ASSEMBLY, until oil is dripping

from the Drip Spout, as shown in Figure 2.

Oil Drip Rate

djustment Screw

Drip Spout

Fill Cap

Figure 2 — Oil Drip Adjustment

Step3: Adjust oil drip rate so that 1 drop occurs every 15-20 seconds.

NOTE

Do not force adjustment screw. It

stops when fully closed.

Page #6 -- SKU: 00422

Check Oil

Check oil level once a week (more often for heavy use).

Step 1: Hold a suitable container underneath the Drain Plug and unscrew as shown in Figure 3.

Figure 3 — Fill Reservoir

Step 2: Tighten the Drain Plug.

Step3: Remove the Fill Cap and add Pneumatic Tool Oil until Reservoir is 3/4 full.

Step 4: Tighten and Fill Cap.

Loosen

Drain Plug

Resevoir

Fill Cap

Page #7 -- SKU: 00422

Greasing

Step 1: Grease ZERK FITTINGS (#35) once every three months (more often for heavy use) as

shown in Figure 4.

Zerk Fittings (#35)

Clamp Screw (#51)

(Located Beneath the

Clamp Frame.)

Figure 4 — Grease Zerk Fittings

Step 2: Grease the CLAMP SCREW (#51) every six months (more often for heavy use).

Page #8 -- SKU: 00422

PARTS LIST

ITEM# DESCRIPTION QTY ITEM# DESCRIPTION QTY

01 Control Valve 1 28 Cylinder Body 1

02 Brass Nipple 1 29 CylinderRod 1

03 Lubricator Assembly 1 30 Rod End Bearing 1

04 InletFitting 1 31 Crank Thrust Washer 2

05 Adjustment Seal 1 32 CrankArm 1

06 Adjustment Jam Nut 1 33 Crank Pin Retaining Ring 2

07 Adjustment Screw 1 34 Crank Pin 1

08 AirHose 1 35 ZerkFitting 2

09 Hose Clamp 2 36 MainShaft 1

10 InletElbow Fitting 1 37 Lock Washer 1/2" 1

11 Cylinder Stud 1 38 1/2"-12Nut 1

12 Shock Metal Washer 2 39 MainBearing 2

13 Shock rubber Washer 2 40 Housing Assembly 1

14 Valve body Screw 3 41 Thrust Washer 1

15 Lower Body Valve 1 42 U-Bolt 1

16 Valve Body O-Ring 1 43 Clamp Frame 1

17 Check Valve Disc 1 44 Handle 1

18 Valve Disc 1 45 Roll Pin 1

19 UpperValve Body 1 46 Clamp Nut (Left Hand) 1

20 Packing 1 47 Jaw Bolt 4

21 Piston Screw 1 48 Clamp Nut (Right Hand) 1

22 Wear Ring 1 49 Thrust Washer 1

23 Piston O-Ring 1 50 Roll Pin 1

24 Piston 1 51 Clamp Screw 1

25 Air Cock 1 52 Jaw Shim 4

26 Rod Bearing 1 53 3/8"16 Nut 8

27 Rod Seal 1 54 Jaw 2

Page #9 -- SKU: 00422

PARTS DIAGRAM

Page #10 -- SKU: 00422

Indice

Altri manuali Central Pneumatic Spruzzatore di vernice

Central Pneumatic

Central Pneumatic 66801 Manuale di installazione

Central Pneumatic

Central Pneumatic 2471 Manuale utente

Central Pneumatic

Central Pneumatic 95793 Manuale utente

Central Pneumatic

Central Pneumatic 69704 Istruzioni per il montaggio

Central Pneumatic

Central Pneumatic 91009 Manuale utente

Central Pneumatic

Central Pneumatic 93205 Manuale utente

Central Pneumatic

Central Pneumatic 91011 Manuale utente

Central Pneumatic

Central Pneumatic 62381 Manuale utente

Central Pneumatic

Central Pneumatic 43760 Manuale utente

Central Pneumatic

Central Pneumatic 97855 Manuale di installazione

Central Pneumatic

Central Pneumatic 93506 Manuale utente

Central Pneumatic

Central Pneumatic 93974 Manuale utente

Central Pneumatic

Central Pneumatic 91011 Manuale utente

Central Pneumatic

Central Pneumatic 94605 Manuale elenco delle parti

Central Pneumatic

Central Pneumatic 30224 Manuale utente

Central Pneumatic

Central Pneumatic 47016 Guida utente

Central Pneumatic

Central Pneumatic 90985 Manuale utente

Central Pneumatic

Central Pneumatic 93270 Manuale utente

Central Pneumatic

Central Pneumatic CENTRAL PNEUMATIC 92841 Manuale utente

Central Pneumatic

Central Pneumatic PAINT SPRAY GUN 30224 Manuale utente

Central Pneumatic

Central Pneumatic 66871 Manuale di installazione

Central Pneumatic

Central Pneumatic 96382 Manuale elenco delle parti

Central Pneumatic

Central Pneumatic 47016 Guida utente

Central Pneumatic

Central Pneumatic CENTRAL PNEUMATIC 93305 Manuale utente

Manuali Spruzzatore di vernice popolari di altre marche

SNOWJOE

SNOWJOE Sunjoe 24V-GS-LTW-RM Manuale utente

Graco

Graco 246737 Manuale per l'uso e la cura

Binks

Binks SV100 Manuale utente

Fimco

Fimco LG-4-3-1 Manuale utente

AG SPRAY

AG SPRAY FS-ATV-25BL Manuale utente

Nordson

Nordson MicroMax 2 Manuale utente

Bonide

Bonide 051 Manuale operativo

zogics

zogics Z-DAS Manuale utente

KISANKRAFT

KISANKRAFT KK-KBS-165 Manuale utente

Matrix

Matrix SG 650 Manuale utente

Anest Iwata

Anest Iwata SGA-3 Guida rapida

paasche

paasche VV Scheda tecnica

Carlisle

Carlisle DeVilbiss JGA-510 Manuale utente

Gardena

Gardena 11120 Manuale utente

Conrad

Conrad Hobby Airbrush K3 Manuale utente

wiwa

wiwa 14025 R/F Manuale utente

Graco

Graco EM 390 Manuale operativo

DeVilbiss

DeVilbiss LUNA2i Manuale utente