Centurion VECTOR2 Manuale utente
LINEAR
SWING GATE
OPERATORS
TM
VECTOR2
Installation Manual
Company Profile
CENTURION SYSTEMS (Pty) Ltd reserves the right to make changes to the products described in this manual without
notice and without obligation of CENTURION SYSTEMS (Pty) Ltd to notify any persons of any such revisions or changes.
Additionally, CENTURION SYSTEMS (Pty) Ltd makes no representations or warranties with respect to this manual.
No part of this document may be copied, stored in a retrieval system or transmitted in any form or by any means electronic,
mechanical, optical or photographic, without the express prior written consent of CENTURION SYSTEMS (Pty) Ltd.
Sales and technical support
to over 50 countries
worldwide
1986 1990 1995 1999 Centurion Systems
Today
100%
testing of
products
In-house
R & D
development
team
Manufacture to
international
quality standard
ISO 9001:2008
After-sales
technical support
from 07h00 - 18h00
Monday to Friday
Contents
page 1
page 2
page 2
page 3
Mechanical Setup
Electrical Setup
Commissioning and Handover
IMPORTANT SAFETY INSTRUCTIONS
1. Declaration of Conformity page 5
2. General Description page 6
Lightning Protection page 7
3. Icons Used in this Manual page 7
4. Specifications page 8
Physical Dimensions page 8
Technical Specifications page 9
Control Card page 10
Power Supply page 10
Power Supply, Control Box and Control Card Assembly 2 page 10
Allowable Gate Mass page 11
5. Product Identification page 12
6. Required Tools and Equipment page 14
7. Preparation of Site page 15
General Considerations for the Installation page 15
Strength of the Pillar page 16
Strength of the Gate and Gate Bracket page 19
Mechano Kit Installation Options page 20
High-Security Kit Installation Options page 21
8. Cabling Requirements page 22
9. Critical Installation Checklist page 23
10. Operator Installation page 24
Determine the Gate Bracket Position page 25
Fasten Gate Bracket to Gate page 27
Adjust Origin Clamp page 28
Inward Swing Gate Setup page 29
Outward Swing Gate Setup page 32
11. Determine Gate Swing Angle page 35
12. Allowable Wind Load page 36
13. Electrical Setup page 37
Secure Control Box to Wall page 37
Connecting all Wiring page 37
Setting the Limits page 38
14. Wiring Diagram for Closing Safety Beams page 40
15. Wiring Diagram for Opening Safety Beams page 41
16. Wiring Diagram for External Radio Receiver and Loop Detector page 42
17. Wiring Diagram for Other Inputs page 43
18. Wiring Diagram for Master Motor (MTRM) page 44
19. Wiring Diagram for Slave Motor (MTRS) page 45
20. Charger and Pillar Light Connections page 46
21. Solar Panel Wiring page 47
22. Setting up Additional Features page 48
23. Menu Navigation Map page 48
24. Controller Features page 52
25. Factory Defaults Schedule page 63
26. Description of Terminal Functions page 69
27. Diagnostics page 72
Diagnostic LEDs page 72
Gate Status LED Indication page 72
LCD Display page 73
Buzzer Feedback page 74
28. Installation Handover page 75
Mount controller enclosure and
connect all wiring
Check cabling requirements
Mechanical Setup
Gather required tools and equipment Page 14
Heed necessary site considerations Page 15
Page 22
Mount the wall bracket Page 25
Install motor and link to gate Page 25
Page 37
These quick steps are for the experienced installer who needs
a checklist to get a standard installation up and running in the
minimum of time.
Detailed installation features and functions are referred to
later in this manual.
Page 1
Fit mechanical endstops Page 38
Electrical Setup
Page 2
Commission system
Commissioning
and Handover
Carry out professional handover to
client
Page 62
Page 74
Connect all wiring
Run setup routine Page 40
8
10
Warnings for the installer
CAREFULLY READ AND FOLLOW ALL INSTRUCTIONS
before beginning to install the product.
All installation, repair, and service work to this product
must be carried out by a suitably qualified person
This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless
they have been given supervision or instruction concerning
use of the appliance by a person responsible for their
safety
Do not activate your gate unless you can see it and can
determine that its area of travel is clear of people, pets, or
other obstructions
NO ONE MAY CROSS THE PATH OF A MOVING GATE.
Always keep people and objects away from the gate and its
area of travel
NEVER LET CHILDREN OPERATE OR PLAY WITH THE
GATE CONTROLS
Secure all easily-accessed gate opener controls in order to
prevent unauthorised use of the gate
Do not in any way modify the components of the
automated system
Do not install the equipment in an explosive atmosphere:
the presence of flammable gasses or fumes is a serious
danger to safety
Before attempting any work on the system, cut electrical
power to the operator and disconnect the batteries
The mains power supply of the automated system must be
fitted with an all-pole switch with contact opening distance
of 3mm or greater. Use of a 5A thermal breaker with all-
pole circuit break is recommended
IMPORTANT
Safety Instructions
ATTENTION
To ensure the safety of people, it is important that you
read all the following instructions.
Incorrect installation or incorrect use of the product
could cause serious harm to people.
The installer, being either professional or DIY,
is the last person on the site who can ensure that the
operator is safely installed, and that the whole system
can be operated safely.
Page 3
Make sure that an earth leakage circuit breaker with a
threshold of 30mA is fitted upstream of the system
Never short-circuit the battery and do not try to recharge the
batteries with power supply units other than that supplied
with the product, or by CENTURION
Make sure that the earthing system is correctly constructed,
and that all metal parts of the system are suitably earthed
Safety devices must be fitted to the installation to guard
against mechanical movement risks such as crushing,
dragging and shearing
It is recommended that at least one warning indicator light be
fitted to every system
Always fit the warning signs visibly to the inside and outside
of the gate
The installer must explain and demonstrate the manual
operation of the gate in case of an emergency, and must hand
the User Guide/Warnings over to the user
Explain these safety instructions to all persons authorised to
use this gate, and be sure that they understand the hazards
associated with automated gates
Do not leave packing materials (plastic, polystyrene, etc.)
within reach of children as such materials are potential
sources of danger
Dispose of all waste products like packaging materials, worn-
out batteries, etc., according to local regulations
Always check the obstruction detection system, and safety
devices for correct operation
CENTURION does not accept any liability caused by improper
use of the product, or for use other than that for which the
automated system was intended
This product was designed and built strictly for the use
indicated in this documentation. Any other use, not expressly
indicated here, could compromise the service life/operation
of the product and/or be a source of danger
Everything not expressly specified in these instructions is not
permitted
Page 4
Page 5
1. Declaration of Conformity
Manufacturer
Centurion Systems (Pty) Ltd
Unit 13 Production Park
Intersection of Newmarket Road and Epsom Avenue
North Riding
Gauteng
South Africa
Declares that the product
Product name: VECTOR2 Swing gate operator
Product options: All variants
Conforms with the following specifications
Safety: SANS 60335-1:2007
IEC 60335-1:2006
Emissions: CISPR 22 CLASS B: Radiated emissions – 30MHz to 1000MHz
CISPR 22 CLASS B: Conducted emissions – 150 KHz to 30MHz
Immunity: IEC 61000-4-2 – Electrostatic discharge
IEC 61000-4-3 – Radiated immunity – 80MHz to 1000MHz
IEC 61000-4-4 – Electrical fast transients/burst
IEC 61000-4-5 – Surge immunity test
IEC 61000-4-6 – Conducted immunity – 150KHz to 80MHz
IEC 61000-4-8 – Power frequency magnetic field
IEC 61000-4-11– Voltage dips and interruption
Standard to which conformity is declared
IEC 60335-1:2006 Safety
IEC 61000-6-3 Emissions
IEC 61000-6-1 Immunity
Signed at North Riding, South Africa on June 21, 2010
Ian Rozowsky
Research & Development Director
2. General Description
Page 6
The VECTOR2 operator has been designed to safely and cost-effectively automate a wide
variety of swing gates, from single light-domestic swing gates to heavy industrial double
swing gates.
The fail-safe and fully redundant Position and Collision Detection system has been
designed and tested to set the standard in safety of operation and to provide an
unparalleled level of reliability and durability in operation.
The gate Travel Limits are managed by a sealed double-redundant opto-electronic system
that has been designed not only to ensure ultra-reliable operation, but also to ensure
precise position and trajectory control. This enables very accurate and reliable collision
detection to ensure safe operation even under trying conditions.
The VECTOR2 control card has been designed to be easy and intuitive to use, with
helpful instructions on the status of the operation being given both during and after the
installation. It also has a built-in diagnostic procedure that can verify every aspect of the
control card onsite.
Some of the advanced features offered by the VECTOR2 controller are:
Fully automated single-button Limit Setup for single and double swing gates
Full graphics LCD display provides an intuitive user interface with built-in diagnostics to
speed up and simplify the installation process
Separate safety inputs for infrared beams on both the closing and opening directions of
the gate
Advanced closed-loop speed control to maintain safe and reliable operation on inclined
gates under windy conditions
Fully configurable gate Run Profiles
Selectable and adjustable Autoclose with pushbutton override
Pedestrian (Partial) opening with automatic closure
Free-exit input
Positive Close Mode
Multiple Modes of Operation
Solenoid lock drive output up to 2A
Holiday Lockout
A status LED output to indicate the gate status remotely
Pillar Light control
Leaf delay is selectable for either gate leaf
Onboard CENTURION receiver with selective adding and deleting of remotes
Altri manuali per VECTOR2
4
Indice
Altri manuali Centurion Apricancello
Centurion
Centurion D5-EVO REPAIR Manuale utente
Centurion
Centurion D3 Manuale utente
Centurion
Centurion R3 Manuale utente
Centurion
Centurion D2 Turbo Manuale utente
Centurion
Centurion D10 Manuale utente
Centurion
Centurion D5-EVO REPAIR Manuale del proprietario
Centurion
Centurion D3 Manuale utente
Centurion
Centurion R3 Manuale utente
Centurion
Centurion D3 Manuale utente
Centurion
Centurion Auto-Mate Manuale utente
Centurion
Centurion R3R5 Manuale utente
Centurion
Centurion BENINCA IT24N Manuale utente
Centurion
Centurion D10 Manuale utente
Centurion
Centurion D5-EVO REPAIR Manuale utente
Centurion
Centurion CP70R5 Manuale utente
Centurion
Centurion D5-EVO REPAIR Manuale utente
Centurion
Centurion Auto-Mate Manuale utente
Centurion
Centurion VECTOR2 Manuale utente
Centurion
Centurion D3 Manuale utente
Centurion
Centurion D10 Manuale utente
