Certa POWERPLUS CT20VGRNDRA Manuale utente

POWERPLUS 20V ANGLE GRINDER

(SKIN ONLY)

CT20VGRNDRA

Save all warnings and instructions for future reference. The term “power tool” refers to your

mains operated (corded) power tool or battery-operated (cordless) power tool.

Work area

•Keep your work area clean and well lit. Cluttered benches and dark areas invite

accidents.

•Do not operate power tools in explosive atmospheres, such as in the presence of

flammable liquids, gases or dust. Power tools create sparks which may ignite the

dust or fumes.

•Keep bystanders and children away while operating a power tool. Distractions can

cause you to lose control of the device.

Electrical safety

1. Power tool plugs must match the outlet. Never modify the plug in any way. Do not

use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and

matching outlets will reduce the risk of electric shock.

2. Avoid body contact with grounded surfaces such as pipes, radiators, ranges, and

refrigerators. There is an increased risk of electric shock if your body is grounded.

3. Do not expose power tools to rain or wet conditions. Water entering a power tool

will increase the risk of electric shock.

4. Do not abuse the cord. Never use the cord to carry the tools or pull the plug from an

outlet. Keep cord away from heat, oil, sharp edges or moving parts. Replace

damaged cords immediately. Damaged cords increase the risk of electric shock.

5. When operating a power tool outdoors, use an extension cord suitable for outdoor

use to reduce the risk of electric shock.

6. If operating a power tool in a damp location is unavoidable, use a Ground Fault

Circuit Interrupter (GFCI) protected supply to reduce the risk of electric shock.

SAFETY & WARNINGS

Personal safety

1. Stay alert, watch what you are doing and use common sense when operating a

power tool. Do not use tool while tired or under the influence of drugs, alcohol, or

medication. A moment of inattention while operating power tools may result in

serious personal injury.

2. Use personal protective equipment. Always wear eye protection. Safety equipment

such as dust mask, non-skid safety shoes, hard hat or hearing protection used for

appropriate conditions will reduce personal injuries.

3. Prevent unintentional starting. Ensure the switch is in the off position before

connecting to a power source and/or battery pack, picking up or carrying the tool.

Carrying power tools with your finger on the switch or energising power tools that

have the switch on invites accidents.

4. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing, and

gloves away from moving parts. Loose clothes, jewellery or long hair can be caught

in moving parts.

5. Remove adjusting keys or wrenches before turning the tool on. A wrench or a key

that is left attached to a rotating part of the tool may result in personal injury.

6. Do not overreach. Always keep proper footing and balance. The enables better

control of the power tool in unexpected situations.

7. Only use safety equipment that has been approved by an appropriate standards

agency. Unapproved safety equipment may not provide adequate protection. Eye

protection must be ANSI-approved and breathing protection must be NIOSH-

approved for the specific hazards in the work area.

Power tool use and care

1. Do not force the tool. Use the correct tool for your application. The correct tool will

do the job better and safer at the rate for which it is designed.

2. Do not use the tool if the switch does not turn it on or off. Any power tool that

cannot be controlled with the switch is dangerous and must be repaired.

3. Disconnect the plug from the power source and/or the battery pack from the power

tool before making any adjustments, changing accessories, or storing the tool.

Such preventive safety measures reduce the risk of starting the tool accidentally.

4. Store idle power tools out of the reach of children and other untrained persons.

Power tools are dangerous in the hands of untrained users.

5. Maintain tools with care. Check for misalignment or binding of moving parts,

breakage of parts and any other condition that may affect the power tool’s

operation. If damaged, have the power tool repaired before use. Many accidents

are caused by poorly maintained power tools.

6. Keep cutting tools sharp and clean. Properly maintained tools with sharp cutting

edges are less likely to bind and are easier to control.

7. Use only accessories that are recommended by the manufacturer for your model.

Accessories that may be suitable for one tool may become hazardous when used

on another tool.

Battery use and care

1. Ensure the switch is in the off position before inserting the battery pack. Inserting

the battery pack into power tools that have the switch on invites accidents.

2. Recharge only with the charger specified by the manufacturer. A charger that is

suitable for one type of battery pack may create a risk of fire when used with

another battery pack.

3. Use power tools only with specifically designated battery packs. Use of any other

battery packs may create a risk of injury and fire.

4. When the battery pack is not in use, keep it away from other metal objects like

paper clips, coins, keys, nails, screws, or other small metal objects that can make a

connection from one terminal to another. Shorting the battery terminals together

may cause burns or a fire.

5. If the appliance is misused or damaged, liquid may be ejected from the battery;

avoid contact. If contact accidentally occurs, flush with water. If liquid contacts

eyes, seek medical help as well. Liquid ejected from the battery may cause irritation

or burns.

6. If the battery is damaged, vapours may be emitted which can irritate the

respiratory system. Provide fresh air and seek medical help in case of inhalation.

7. Do not open the battery. Keep the battery away from sources of heat, such as fire

or continuous direct sunlight, to avoid the danger of explosion.

Grinder use and safety

•This tool is intended to function as a grinder or cut-off. Read all safety instructions,

warnings and specifications provided with this power tool. Failure to follow all

instructions may result in electric shock, fire, or injury.

•Operations such as sanding, wire brushing or polishing are not recommended with

this power tool. Operations for which the power tool was not designed for may

create a hazard and result in injury.

•Do not use accessories that are not specifically designed and recommended by

Kogan.com. Just because an accessory can be attached to the tool does not

assure safe operation.

•The rated speed of the accessory tool must be at least equal to the maximum

speed marked on the power tool. Accessories running faster than their rated speed

can break apart and fly away.

•The outside diameter and the thickness of your accessory must be within the

capacity rating of your power tool. Incorrectly sized accessories cannot be

adequately guarded or controlled.

•The arbour size of wheels, flanges, backing pads or other accessories must properly

fit the spindle of the power tool. Accessories with arbour holes that do not match

the power tool will run out of balance, vibrate excessively, and may cause loss of

control.

•Keep bystanders a safe distance away from the work area. Anyone entering the

work area must wear personal protective equipment. Fragments of workpiece or

part of a broken accessory may fly away and cause injury beyond the immediate

area of operation.

•Never lay the power tool down until the accessory has come to a complete stop.

The spinning accessory may grab the surface and pull the power tool out of your

control.

•Never run the power tool while carrying it by your side. Accidental contact with the

spinning accessory could snag your clothing, pulling the accessory into your body.

•Never cut, drill or saw in concealed areas where there may be electric, gas or water

lines. Use a suitable detector to locate such lines.

Even when the tool is used as intended, it is not possible to eliminate all residual risk factors.

The following hazards may still arise:

1. Damage to lungs if an effective dust mask is not worn.

2. Damage to hearing if effective hearing protection is not worn.

3. Health defects resulting from vibration emission.

WARNING: This machine produces an electromagnetic field during operation.

This field may interfere with active or passive medical implants. Users with such

implants should consult with their doctor before using this device.

Spindle Lock

Adjustable Safety Guard

Auxiliary Handle

Switch

Main Handle

Battery Pack (Not Included)

Battery Charger (Not Included)

Push Lock Button

OVERVIEW

Charging the battery pack (not included)

1. Remove the battery pack (6) from the handle, pressing the push lock button (8)

downwards to unlock it.

2. Check that your mains voltage is the same as that marked on the rating plate of

the battery charger. Plug the mains plug of the charger (7) into the mains socket.

3. The temperature of the battery pack may rise slightly during the charging

operation. This is normal.

If the battery pack fails to charge, please check the following.

•Whether there is the voltage at the socket outlet.

•Whether there is proper contact at the charging contacts on the charger.

If the battery is still failing to charge after checking these issues, please contact the

Kogan.com customer support team.

To ensure that the battery pack provides a long service life, you should take care to keep it

charged. Never fully discharge the battery pack, as this will greatly reduce the battery

lifetime.

Changing the tool

Before performing any changes to the power tool (including maintenance and tool changes),

as well as during storage or transport, set the rotation direction switch to the centre position.

Unintentional switching of the On/Off button may lead to injuries.

Attaching the auxiliary handle

For safety reasons, the auxiliary handle must be assembled when using this tool.

1. Screw the auxiliary handle into one of the attachment points on the tool head.

2. Make sure the handle is securely fastened.

OPERATION

Adjusting the grinding guard

1. Loosen the screw on the guard with a suitable screwdriver. Do not undo until the

screw is removed completely.

2. Adjust the guard to a position that still protects you from flying sparks.

3. Fasten the screw.

Installing the grinding disc

1. Make sure the guard is securely in place.

2. Place the inner flange on the spindle. Ensure it is aligned on the two flats.

3. Check the rated speed on the grinding disc. Do not use a disc with a rated speed

lower than the speed shown on the tool label.

4. Fit the disc onto the spindle over the inner flange.

5. Press the spindle lock button to prevent movement of the spindle.

6. Keep the lock button pressed in and tighten the threaded outer flange by turning

the lock nut wrench.

Removing the grinding disc

1. Press the spindle lock button (1).

2. Loosen the spindle lock nut (a) by turning the nut counter clockwise with the

wrench.

3. Remove the threaded outer flange.

4. Remove the grinding disc from the spindle.

Switch

1. To turn the grinder on, hold the rear of the switch, then push forward until the

switch won't move any further.

2. Press the switch down.

Indice

Altri manuali Certa Macinacaffè

Certa

Certa PowerPlus 18V Angle Grinder Manuale utente

Manuali Macinacaffè popolari di altre marche

Parkside

Parkside PWS 230 C3 Manuale utente

SUHNER ABRASIVE

SUHNER ABRASIVE ASC 9 Manuale tecnico

PTA

PTA P1322 Manuale utente

Crown

Crown CT13313 Manuale utente

Parkside

Parkside 280250 Manuale utente

Climax

Climax VM2150 Series Manuale utente

Jet

Jet JPSG-618M1 Manuale di servizio

Makita

Makita GA4030 Manuale utente

DeWalt

DeWalt DWEN202 Manuale utente

Grizzly

Grizzly G2790 Manuale utente

Fein

Fein MSf843-1a Manuale utente

Bosch

Bosch GWS 14,4 V PROFESSIONAL Manuale utente

RAMSET

RAMSET CBAGR18 Manuale utente

Bosch

Bosch 8-115 Z Manuale utente

STEELE PRODUCTS

STEELE PRODUCTS SP-PB008 Manuale utente

MW TOOLS

MW TOOLS ME15W Manuale utente

Caravaggi

Caravaggi SP 20 Istruzioni operative

SUHNER ABRASIVE

SUHNER ABRASIVE UWK 10-R125 Manuale tecnico