Cervélo P5X Manuale utente
P5X MANUAL
INTRODUCTION
Three years of extensive research have resulted in the most advanced triathlon bicycle ever created. Not only engineered to carry you to victory, your P5X has been
designed to support all of your service, nutrition and training requirements seamlessly. Although Cervélo strongly recommends that your bicycle be assembled by your
Cervélo retailer, please take time to familiarize yourself with this assembly guide, as this bicycle contains unique components, and requires an understanding of the
disassembly process for travel.
We thank you for making the choice to purchase your Cervélo P5X, and we hope that you enjoy the many hours you will spend with us.
This document has been prepared to guide you through the assembly of the unique features of the P5X, but is intended only as a supplement to the assembly
instructions offered by your component manufacturer. Please pass these instructions to the consumer along with the completed bicycle.
TABLE OF CONTENTS
Version 2 - 2017-06-07
Introduction ......................................................................................................1
Frame Features ................................................................................................2
Small Parts .......................................................................................................3
Frame Storage Cases.......................................................................................4
Aerobar Components Overview .......................................................................5
Fork Installation ................................................................................................7
Brake Housing Installation................................................................................8
Basebar Wiring...............................................................................................10
Basebar Installation........................................................................................11
Riser Assembly...............................................................................................12
Extension and Pad Mount..............................................................................13
Arm Cup and Pad Installation ........................................................................14
Multi-Bend Extensions ...................................................................................15
Aerobar Assembly Installation........................................................................16
Electric Cable Routing....................................................................................17
Stem Cover Installation ..................................................................................19
Mechanical Cable Routing .............................................................................21
Smartpak Installation......................................................................................23
Speedcase Installation ...................................................................................25
Internal Routing Guide Installation .................................................................26
Stealthbox Installation....................................................................................27
Seat post Assembly ......................................................................................28
Cutting Seat Post ..........................................................................................30
Through-Axle Wheel Installation.....................................................................31
Appendix: P5X Fork Owner's Instructions .....................................................33
x2
x2
x2
2 3
SMALL PARTS
Designed to accommodate electronic, mechanical and hydraulic controls, the P5X frame is engineered to provide seamless integration of all shifting systems,
regardless of method or brand. In order to do so, you will require the parts shown below:
BB Battery Mount
MT-PXBINT
BB Cable Guide
BBG-PX110
Bushing for Brake Hose
BU-DH1290 Internal Routing Guide
CBG-MPXINTF
Seat Post Clamp
SPC-P5X110
Wire Clip
BRW-MPXDi2
E-Wire Grommet
Open Type
GR-BEC-OPEN
Top Tube Routing
Guide
GR-MPXTT
E-Wire Grommet
Closed Type
GR-BVT-TT-S5
FRAME FEATURES
A guide to your Cervélo P5X frame.
Rear dropout cable exit
hole, electric and
mechanical
Front derailleur wire
exit hole, electric and
mechanical
Bottom bracket cable
and battery port
Stealthbox storage
port.
Top tube internal
cable port
Smartpak in-frame
compartment port
Speedcase
mounting points.
4 5
AEROBAR COMPONENTS OVERVIEW
Basebar Plate
Stem
Riser Post
Clamp
Riser Post
Angle Adjustment Plate
Extension and Pad Mount
Multi-Bend
Extensions
Arm Cups and Pads
Base Bar
FRAME STORAGE CASES
Speedcase
Stealthbox
Smartpak
(In frame portion)
Smartpak
6 7
FORK INSTALLATION
1. Check the stem, and headset components to make sure there are no sharp or rough edges on any of
the surfaces which could cut or damage the steerer tube. If any rough edges are detected, have the
components repaired (sharp edges removed) or replaced before proceeding.
2. Press the upper and lower headset bearings into the frame, and insert the fork into the head tube.
3. Slide the compression ring onto the steerer, and down until it fully seats in the top of the upper headset
bearing. The split in the compression ring must be oriented toward to left or right side of the steerer –
never towards the front or back.
4. Slide the stem onto the fork steerer oriented as shown. Note the stem must engage both the fork steerer
and the external steerer. Do not use grease on the fork steerer.
5. Lightly grease the threads of the stem top cap bolt, and the stem clamp bolts.
6. Place the stem cap on top of the stem and insert the greased bolt through the cap to engage with the star
nut. Tighten the bolt only enough to remove all play from the headset, and ensure that the fork still rotates
freely.
7. Tighten the greased stem bolt(s) to the steerer using a torque wrench. Tighten the bolts evenly and
alternately to a maximum of 5 Nm.*
8. As a nal check ensure that the fork rotates freely in the head tube without any play or binding. If any
problem is detected, loosen the bolts and perform steps 6) to 7) again.
*Do not exceed the maximum torque specification for the stem. Correct tightening force on fasteners
– nuts, bolts, screws – on your bicycle is very important. Too little force, and the fastener may not hold
securely. Too much force, and the fastener can strip threads, stretch, deform or break. Either way,
incorrect tightening force can result in component failure, which can cause you to loose control and
fall. In case of a disagreement or a conflict between any literature on recommended torque values,
always use the recommended torque specification as printed on the component or recommended by
the component manufacturer over any recommendation listed in this manual.
P5X ASSE MBLY
8 9
BRAKE HOUSING INSTALLATION
It is recommended that the hydraulic brake hoses or brake cable housing is installed rst. These routing illustrations are intended as a supplement to the
manufacturer’s installation instructions only. For both hydraulic and mechanical disc brakes, please refer to the component manufacturer’s service center or website
for further information.
1. Route hydraulic brake hose or mechanical brake housing through
the frame and fork.
2. Install calipers as per manufacturer's instructions.
3. Install Brake Hose Bushings to secure hose and housings in place.
10 11
BASEBAR INSTALLATION
Basebar - Low Position
Basebar - High Position
1. Lightly grease the threads of the four M5 stem xing screws.
2. Position both halves of the base bars as shown in the up, or down
conguration as determined during tting.
3. Install the Basebar Plate and hold the assembly in place.
4. Insert the four greased M5 xing screws as shown to x the
basebar into place.
5. Tighten to 6 Nm maximum torque.
BASEBAR WIRING
1. Feed electric cable through each side of the basebar from
the front.
2. With brake lines already installed in frame and exiting from
the top tube cable port, push through from back of bar.
3. Install brake levers as per manufacturer’s instructions.
12 13
EXTENSION AND PAD MOUNT
Setback Position
Forward Position
The Pad and Extension Mount can be
attached in two positions:
1. Attach Pad and Extension Mount to Angle Adjust Plate using
four lightly greased M5 xing screws.
2. Torque to 6 Nm.
RISER ASSEMBLY
+12°
-5°
0°
The riser assembly has +12/-5 degrees of tilt adjustment.
1. Lightly grease the threads and spherical washer faces of the
two angle adjust plate xing bolts.
2. Lightly grease the tilt interfacing surface on both the Stem Riser
Post and the Angle Adjust Plate.
3. Assemble the Stem Riser Post components as depicted left.
4. Tighten to 6 Nm.
Grease
Grease
14 15
Minimum Insertion
MULTI-BEND EXTENSIONS
1. Install and adjust extensions.
2. Torque to 5 Nm.
ARM CUP AND PAD INSTALLATION
1. Attach the Arm Cups to the Extension and Pad Mount using
two lightly greased M5 xing screws.
2. Torque to 6 Nm.
Aerobar water bottle mount.
16 17
ELECTRIC CABLE ROUTING
It is recommended that electric cabling and junction points be installed after the brake hose has been installed. These routing illustrations are intended as a
supplement to the manufacturer’s installation instructions only. Please refer to the component manufacturer’s service center or website for further information.
1. Ensure all wires are located
inside frame, with Shimano
Junction B located to the rear
of the Bottom Bracket.
2. Attach Battery to BB Battery
Mount using 2 zip-ties.
AEROBAR ASSEMBLY INSTALLATION
Attach Wire Clip by sliding over
stem from the rear.
1. Apply a light coat of grease to inside of fork.
2. Apply grease to sliding surfaces within Riser
Post Clamp, and tighten down M3 screw, then
back off by quarter turn.
3. Loosen stem bolts slightly, and install Riser
Post, followed by Riser Post Clamp.
4. Torque Riser Post Clamp to 8 Nm.
5. Retighten stem bolts evenly and alternately to
5 NM.
Grease
M3 Screw
Altri manuali per P5X
1
Indice
Altri manuali Cervélo Bicicletta
Cervélo
Cervélo R5 Disc Manuale utente
Cervélo
Cervélo ASPERO Manuale utente
Cervélo
Cervélo R3 Rim Manuale utente
Cervélo
Cervélo P5 Manuale utente
Cervélo
Cervélo PX Series Manuale utente
Cervélo
Cervélo S5 Istruzioni e ricette
Cervélo
Cervélo S3 2019 Manuale utente
Cervélo
Cervélo C SERIES Manuale utente
Cervélo
Cervélo R5 Disc Manuale utente
Cervélo
Cervélo multi-speed racing bicycles Manuale utente
