Chamberlain TAC11 Istruzioni per il montaggio

Installation and Programming Manual

The Chamberlain Group

845 Larch Ave.

Elmhurst, IL 60126-1196

www.liftmaster.com

TAC1

Telephone Entry System

TABLE OF CONTENTS

SPECIFICATIONS 3

Cable Requirements 3

Dimensions 3

Carton Inventory 3

INSTALLATION 4-11

Mount the Back Panel 4

Description of the Processor Board 4

Overview of Telco Wiring 5

Wiring the Unit With a Telco Line 6

Wiring the Unit Without a Telco Line 6

Wiring a Gate Operator 7

Wiring an Auto-Call Sensor 7

Wiring a Gate Operator and a Door Strike Lock 8

Wiring a Gate Operator and a Maglock 8

Wiring a Door Strike Lock 9

Wiring a Maglock 9

Earth Ground Rod 10

Power Wiring 10

Plug the Transformer into the Outlet 11

Mount the Unit 11

Set the Master Code 11

TESTING 12

Test the Gate/Door Relay 12

Test the Telephone Connections 12

PROGRAMMING 13-19

From the TAC1 Keypad 13

Code Setup and Code Operation 14

From the Telephone 15-16

Program a Pre-Installed Liftmaster Receiver 16

Quick Reference 17-18

TAC1 MASTER CODE 19

LIMITED WARRANTY 20

CABLE REQUIREMENTS

DIMENSIONS

CARTON INVENTORY

Power Supply: 12 Vac 20 VA

Unit (unlocked) (1)

Key (1)

12 Volt ac 20VA Plug-In UL Listed Power Transformer (1)

Manual (1)

8-3/4"

3-3/4"

3/4"

1/4"

4-1/4"

2-3/4"

SPECIFICATIONS >> CABLE REQUIREMENTS, DIMENSIONS AND CARTON INVENTORY

Outdoor installations require shielded cable. Non-shielded cable can be used for indoor installations ONLY.

PROCESSOR BOARD WIRE TYPE RECOMMENDATIONS

From the power transformer at 120 Vac outlet 2 - Conductor Cable Shielded Only - See Power Wire Table Below

From the door strike, maglock or gate operator 2 - Conductor Cable See device specifications for wire size

From the strike power supply (if needed) 2 - Conductor Cable See device specifications for wire size

From the Earth ground to processor board 12 AWG copper wire,

PVC insulated

12 AWG copper wire,

uninsulated

Belden #9912

Belden #8011

Residence and Telco phone lines 24 AWG twisted

pair telephone wire

Shielded - Belden #9502

From the Processor Board 24 AWG twisted

pair telephone wire

Shielded - Belden #9502

Between Processor Boards on

multiple entrance installation

24 AWG twisted

pair telephone wire

Shielded - Belden #9502

POWER WIRE TABLE

NOTE: Chamberlain is not responsible for conflicts between the information listed in the above table and the requirements of local building

codes. The information is for suggested use only. Check local building codes before installation.

DISTANCE AC POWER WIRE SIZE

Under 30 feet 18 AWG

30 - 75 feet 18 AWG

75 - 150 feet 18 AWG

150 - 250 feet 16 AWG

250 - 500 feet 12 AWG

AUTOCALL

RELAY 2 RELAY 1

POWER

LINE

TIP

RING

PHONE

TIP

RING

11 2

1Autocall Input: Connector for accessory device to trigger

home dialing.

2Power Connector: 12 volt AC power input. 8Ground Wire: Wire must be connected to positive earth

ground. See Earth Ground Rod.

7Tamper Switch

5Phone Output: Telephone return connection to home or

office phones.

6Line Input: Telephone input connection from “Telco” service

provider.

4Relay 1 Output: Form “C” primary control relay.

12 Relay 1 (Primary) Output Status LED

13 Relay 2 (Secondary) Output Status LED

10 Voice Data Send Status LED

9Status LED

11 Power Status LED

Choose the mounting location for the unit. Remove the back panel and

attach the unit to a solid surface or post (hardware not provided).

INSTALLATION >> MOUNT THE BACK PANEL AND OVERVIEW OF THE PROCESSOR BOARD

DESCRIPTION OF THE PROCESSOR BOARD

MOUNT THE BACK PANEL

3Relay 2 Output: Form “C” secondary control relay.

NC NC

NO NO

COM COM

Home Phone

Ring

(Not Provided)

Telco Entrance Box

Demarcation Point

Tip

Alarm System

Position

NOTES:

• The voltmeter measurement between the Tip and Ring should

be between 48 and 53 Vdc.

• Never run data wires and high voltage wires in the same

conduit. The high voltage wires may interfere with the data

wires and cause the system to malfunction.

• Reversed polarity will not damage the unit, however, some

telephones will not function properly.

Tip

Ring

Telco Entrance Box

Demarcation Point

(non fourni)

Emplacement du

système d’alarme

PHONE LINE

TIP

RING

TIP

RING

Telco

Alarm System

Position (Not Provided)

Home Phone

Many phone companies have updated their color standards due to

the use of Cat 5 cable for most phone line installs, and keep

residential and business installs in line with each other. In the new

standard, there is no green, red, black or yellow wires, they have

been replaced by white/blue, blue/white, white/orange, and

orange/white. If the wire is primarily orange with white stripes

then that color is orange/white. Refer to the table below. The NID

labels will most likely have the old coloring scheme on them, and

most telephone wiring components you can purchase will still

reflect the original colors.

NOTE: If the unit will be connected with an

alarm system, you must connect the telephone

line to the alarm system first in the series from

the Telco box. If the units are not connected in

this order, they will not operate properly.

Function Old Color Standard New Color Standard

Tip 1 Green White/Blue

Ring 1 Red Blue/White

Tip 2 Black White/Orange

Ring 2 Yellow Orange/White

INSTALLATION >> OVERVIEW OF TELCO WIRING

AUTOCALL

EXIT 2

COM

EXIT 1

HOUSETELCO

Notes about wire connectors

(terminal blocks):

• Wire connectors can be

removed to simplify wiring.

• DO NOT overload wire

connectors. Use ONLY one

wire per hole.

Typical Telco Overview

Typical Telco Overview With The Unit

WIRING THE UNIT WITH A TELCO LINE

WIRING THE UNIT WITHOUT A TELCO LINE

PHONE LINE

TIP

RING

TIP

RING

Ring Ring

Tip Tip

Telco Entrance Box

Demarcation Point

Ringer Equivalence Number (REN) = 3

The unit can be a stand alone system that allows

communication between the unit and the resident’s phones.

PHONE LINE

TIP

RING

TIP

RING

Ring Ring Ring Ring

Tip

Telco Entrance Box

Demarcation Point

Telco

Tip Tip Tip

Ringer Equivalence Number (REN) = 5

INSTALLATION >> WIRING THE UNIT WITH A TELCO LINE AND

WIRING THE UNIT WITHOUT A TELCO LINE

Never run data wires and high voltage wires in the same conduit. The high voltage wires may interfere with the data wires

and cause the system to malfunction.

AUTO CALL

Loop Sensor

(Normally Open)

Loop

Detector

WIRING A GATE OPERATOR (NORMALLY OPEN)

Primary Gate

Operator

(Strike Open Input)

RELAY 1RELAY 2

(Normally Open)

COM

(Common)

The gate operator can be connected to Relay 1 or Relay 2. See the

Programming section for information about configuring Relays 1

and 2.

The Auto-Call feature will enable the unit to contact the resident

when a driveway sensor (or any device that provides a contact

closure) is activated.

WIRING AN AUTO-CALL SENSOR

INSTALLATION >> WIRING A GATE OPERATOR (NORMALLY OPEN) AND

WIRING AN AUTO-CALL SENSOR

AUTOCALL

EXIT 2

COM

EXIT 1

HOUSETELCO

Notes about wire connectors

(terminal blocks):

• Wire connectors can be

removed to simplify wiring.

• DO NOT overload wire

connectors. Use ONLY one

wire per hole.

Primary Gate Operator

(Strike Open Input)

COM

(Common)

(Normally Open)

NOTE: For DC power

install a 1N4001 diode

or equivalent.

NOTE: For AC power install a

Siemens S10K30 MOV

(Metal Oxide Varistor) or equivalent.

AC or DC

Power

COM (Common)

NO (Normally Open)

NOTE: Do not use

the unit’s power supply

for the door strike.

Door Strike

RELAY 1RELAY 2

WIRING A GATE OPERATOR (NORMALLY OPEN) &

A DOOR STRIKE LOCK (NORMALLY OPEN)

WIRING A GATE OPERATOR (NORMALLY OPEN) &

A MAGLOCK (NORMALLY CLOSED)

The door strike can be connected to Relay 1 or Relay 2. See the

Programming section for information about configuring Relays 1

and 2.

AUTOCALL

EXIT 2

COM

EXIT 1

HOUSETELCO

Notes about wire connectors

(terminal blocks):

• Wire connectors can be

removed to simplify wiring.

• DO NOT overload wire

connectors. Use ONLY one

wire per hole.

INSTALLATION >> WIRING A GATE OPERATOR (NORMALLY OPEN) A DOOR STRIKE LOCK

(NORMALLY OPEN) AND WIRING A GATE OPERATOR (NORMALLY

OPEN) & A MAGLOCK (NORMALLY CLOSED)

NOTE: Install a 1N4001

diode or equivalent.

NOTE: Do not use

the unit’s power

supply for the maglock.

DC Power

Maglock

Primary Gate Operator

(Strike Open Input)

COM

(Common)

(Normally Open)

RELAY 1RELAY 2

COM (Common)

NC (Normally Closed)

The maglock can be connected to Relay 1 or Relay 2. See the

Programming section for information about configuring Relays 1

and 2.

RELAY 1RELAY 2

NOTE: For DC power install a 1N4001

diode or equivalent.

AC or DC Power

COM (Common)

NO (Normally Open)

NOTE: Do not use

the unit’s power supply

for the door strike.

Door Strike

WIRING A DOOR STRIKE LOCK (NORMALLY OPEN)

RELAY 1RELAY 2

NOTE: For AC power

install a Siemens

S10K30 MOV

(Metal Oxide Varistor)

or equivalent.

NOTE: For DC power install

a 1N4001 diode or equivalent.

NOTE: Do not use the

unit’s power supply for the

maglock.

AC or DC

Power

Maglock

COM (Common)

NC (Normally Closed)

WIRING A MAGLOCK (NORMALLY CLOSED)

The door strike can be connected to Relay 1 or Relay 2. See the

Programming section for information about configuring Relays 1

and 2.

The maglock can be connected to Relay 1 or Relay 2. See the

Programming section for information about configuring Relays 1

and 2.

INSTALLATION >> WIRING A DOOR STRIKE LOCK (NORMALLY OPEN) AND

WIRING A MAGLOCK (NORMALLY CLOSED)

AUTOCALL

EXIT 2

COM

EXIT 1

HOUSE TELCO

Notes about wire connectors

(terminal blocks):

• Wire connectors can be

removed to simplify wiring.

• DO NOT overload wire

connectors. Use ONLY one

wire per hole.

Ensure that the unit is grounded properly. The unit contains a

number of static sensitive components that can be damaged by

static discharge.

To AVOID damaging gas, power or other underground utility

lines, contact underground utility locating companies BEFORE

digging.

NOTES:

• Use a minimum of 12 gauge wire in most cases. The type and

length of the earth ground rods vary by region. Contact the

building inspector’s office in the municipality where you plan to

install the unit for correct grounding materials and installation

procedures.

• Do not ground the unit to a pedestal post (gooseneck) if one is

used.

EARTH GROUND ROD

Other Ground Sources within

12' of the unit

Green Ground Wire

Earth Ground

Rod

Ground to

Metallic Cold

Water Pipe

Ground to

Existing

Electrical

System

12 AWG Minimum

Electrical

Panel

12' Maximum

POWER

The TAC 1

MUST be

grounded.

ffOOff

Main

Room

Eug R. m

O p er R. m

Eu g . D ept .

M a nu . 1 R m

Main D ept.

Man .

u2Rm

Air (1)

Conditioner

)2(

noitidnoC

Conference

Room1

Conference

Rm 2, 3

Refer.

Bus 1, 2, 3

Conference

Room2

oC pm.

Ser ev 2

oCp

Serve 1

12 Vac

Power (included)

Dedicated Outlet

Dedicated 10 Amp Minimum Circuit Breaker

TAC 1

NOTE: Chamberlain is not responsible for conflicts between the information listed in the above table and the requirements of local building

codes. The information is for suggested use only. Check local building codes before installation.

POWER WIRING

The 110 Vac outlet must be dedicated to the unit only. This outlet

should be wired back to its own 10 Amp minimum circuit

breaker. This will prevent two problems:

• Other equipment cannot introduce spikes, noise, surges, or

dips into the power circuit.

• The system’s operation will not be affected if any other

equipment develops a short circuit across the power line.

Connect the transformer into a 110 Vac outlet after all

connections have been made, any other type of outlet will cause

damage to the system.

POWER WIRE TABLE

DISTANCE AC POWER WIRE SIZE

Under 30 feet 18 AWG

30 - 75 feet 18 AWG

75 - 150 feet 18 AWG

150 - 250 feet 16 AWG

250 - 500 feet 12 AWG

INSTALLATION >> EARTH GROUND ROD AND POWER WIRING

1. Install the earth ground rod within 12 feet of the unit.

2. Attach a 12 AWG wire to the unit ground wire with a wing nut.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Chamberlain Sistema di interfono

Chamberlain

Chamberlain LiftMaster ELITE EL25 Manuale utente

Chamberlain

Chamberlain LSIAC Manuale utente

Chamberlain

Chamberlain LiftMaster 831-2LM Manuale utente

Chamberlain

Chamberlain 845EML Manuale utente

Chamberlain

Chamberlain ROI2 Manuale utente

Chamberlain

Chamberlain APEX Access Device Manuale utente

Chamberlain

Chamberlain Elite EL Series Manuale del proprietario

Chamberlain

Chamberlain Smart Video Intercom M Manuale utente

Chamberlain

Chamberlain RFDIC Manuale utente

Chamberlain

Chamberlain LiftMaster ELITE EL25 Manuale utente

Chamberlain

Chamberlain RIFMS2 Manuale utente

Chamberlain

Chamberlain 75EV Manuale utente

Chamberlain

Chamberlain NLS1 Manuale utente

Chamberlain

Chamberlain LiftMaster FDI Manuale utente

Chamberlain

Chamberlain ELITE EL2000LG Manuale del proprietario

Chamberlain

Chamberlain MyQ Business CAPXL Manuale utente

Chamberlain

Chamberlain Elite EL25N Manuale utente

Chamberlain

Chamberlain WIRELESS PORTABLE INDOOR/OUTDOOR INTERCOM... Manuale utente

Chamberlain

Chamberlain GAILM Manuale utente

Chamberlain

Chamberlain RWIS Manuale utente

Chamberlain

Chamberlain LIFTMASTER MUGAPLM Manuale utente

Chamberlain

Chamberlain LiftMaster Professional RIFM1LM Manuale utente

Chamberlain

Chamberlain LSIA Manuale utente

Chamberlain

Chamberlain NDIS Manuale utente

Manuali Sistema di interfono popolari di altre marche

Bticino

Bticino LINEA 3000 Manuale utente

MSI

MSI MSI-140 Manuale utente

golmar

golmar Stadio Plus Manuale utente

CyberData

CyberData 011211 series Manuale

Vidos

Vidos duo M1021 Manuale utente

Vimar

Vimar ELVOX 7539/E Manuale utente

SSS Siedle

SSS Siedle BTSV 850-03 Manuale utente

Dahua

Dahua VTO Series Manuale utente

Elvox

Elvox 5651 Manuale utente

Videx

Videx VIDEOKIT Series Manuale utente

Rocom

Rocom Doortello Business FW T2.05W2.04 Manuale utente

Viking

Viking E-35-EWP Manuale utente

Safeguard Supply

Safeguard Supply LRA-EX1000 Manuale utente

SSS Siedle

SSS Siedle BFCV 850 Series Manuale utente

GRD

GRD MAX V2 Manuale utente

Alecto

Alecto ADI-250 Manuale utente

Aiphone

Aiphone IE-8MD Manuale utente

Perel

Perel EDB4 Manuale utente