Champion WHEELYBIRD 40909 Manuale utente
WARNING: THIS MACHINE CAN CAUSE SERIOUS INJURY OR DEATH!
THOROUGHLY READ INSTRUCTIONS BEFORE INSTALLING OR OPERATING TRAP!
WHEELYBIRD
AUTO-FEED TRAP
Part No. 40909
Instruction Manual
TM
Table of Contents
Section Page
I. Introduction ............................................................................ 1
II. Safety ..................................................................................... 2
III. Assembly and Installation ...................................................... 4
1. Unpacking ......................................................................................4
2. Contents .........................................................................................5
3. Assembly ........................................................................................7
A. Assemble Frame .........................................................................7
B. Attach the Trap to the Frame.......................................................8
C. Install the Mainspring..................................................................9
D. Attach the Throwing Arm Path Indicator .....................................10
E. Attach the Magazine Assembly....................................................11
F. Setup ..........................................................................................11
IV. Operation................................................................................ 12
V. Adjustments............................................................................ 13
1. Throwing arm limit switch ..............................................................13
2. Elevation Adjustment ......................................................................15
3. Distance Adjustment.......................................................................16
VI. Troubleshooting...................................................................... 17
VII. Maintenance ........................................................................... 18
VIII. Replacement Parts ...............................................................................19
IX. Warranty Information ..........................................................................19
X. Contact Information .............................................................................20
1
I. Introduction
The WheelyBirdTM Auto-Feed Trap is designed for the active sporting clays, trap, and
skeet shooter looking for an automatic, lightweight, and portable machine for
practice/fun shooting.
Features and benefits of the WheelyBirdTM Auto-Feed Trap:
Safety
ON-OFF-SAFE RELEASE switch provides safe method to uncock throwing arm
Arm path indicator ring provides visual indication of throwing arm path for safety
20 amp circuit breaker protects electrical wires and motor
Convenience
Lightweight and portable - approximately 48 lbs
Detachable magazine holds 50 targets
Throws standard 108 mm or 110mm international clay targets
25 ft. release cord with foot pedal release
Two-wheeled frame with handle for easy movement
Performance
Fast, 2-second cycle time
Standard throwing range of 55yds at 25 deg elevation angle
Runs off 12 volt battery (deep cycle type recommended)
Balanced throwing arm with replaceable flight rail
2
II. Safety
WARNING: THIS MACHINE CAN CAUSE SERIOUS INJURY OR DEATH!!!!
THOROUGHLY READ INSTRUCTIONS BEFORE INSTALLING OR OPERATING TRAP!
DO NOT STAND IN FRONT OF THE TRAP WHEN IT IS IN THE COCKED POSITION.
SERIOUS INJURY OR DEATH CAN RESULT.
THIS TRAP IS CAPABLE OF THROWING TARGETS A DISTANCE OF OVER 65 YARDS.
USE ONLY IN AREAS WHERE THERE IS NO RISK OF CAUSING DAMAGE, OR HITTING
A PERSON WITH A TARGET.
KNOW YOUR BACKSTOP. ENSURE THERE IS A SAFE PERIMETER THROUGHOUT
TARGET FLIGHT PATH SUFFICIENT FOR AMMUNITION USED.
WARNING: IF THERE IS A TARGET ON THE THROWING ARM, SAFE RELEASING
THE ARM WILL THROW THE TARGET. DO NOT STAND IN FRONT OF THE TRAP WHILE
SAFE RELEASING THE THROWING ARM.
CAUTION: THE TRAP MUST HAVE AMPLE CLEARANCE AROUND THE TRAP. THE
ON/OFF/SAFE RELEASE SWITCH FOR THE TRAP IS LOCATED ON THE REAR OF THE
TRAP AND ALLOWS THE TRAP TO BE UNCOCKED BEFORE APPROACHING IT.
DO NOT INSTALL THE TRAP IN AN AREA THAT DOES NOT ALLOW SAFE (REAR)
ACCESS TO THE TRAP AND THE ON/OFF/SAFE RELEASE SWITCH DURING LOADING
AND USE.
1. All personnel operating the trap should be thoroughly familiar with the
operating instructions and the safety issues relating to the trap.
2. Do not leave trap in the cocked position. Not only is this potentially dangerous,
but it puts undue stress on the mainspring.
3. Always load and operate the trap from the rear (switch end).
4. Keep hands and body outside the trap and throwing arm path indicator areas
while the trap is operating. This ring shows the throwing arm‟s path when
throwing a target, and should always be attached to the trap when it is in use.
5. Be aware that a cracked or broken target thrown from the trap will sometimes
scatter pieces out the right side of the machine as the arm throws. These
pieces may hit nearby unsuspecting bystanders.
6. Always wear eye and hearing protection when shooting.
3
WARNING: BEFORE PERFORMING ANY REPAIR, MAINTENANCE, OR ASSEMBLY,
MAKE SURE THE THROWING ARM IS IN THE UNCOCKED POSITION (SEE BELOW),
THE ON/OFF/SAFE RELEASE SWITCH LOCATED ON THE REAR OF THE TRAP IS IN
THE „OFF„ POSITION (SEE PHOTO BELOW) , AND THE BATTERY IS DISCONNECTED
FROM THE TRAP.
If the throwing arm is in the cocked arm position (see photo below), uncock
the throwing arm by first connecting the red battery lead to the positive (+)
terminal and the black battery lead to the negative (-) terminal on the battery.
Momentarily press the on/off/safe release switch to the “SAFE RELEASE”
position to release the throwing arm. After the trap fires, release the
ON/OFF/SAFE RELEASE switch allowing it to return to the “OFF” position. The
throwing arm should now be in the uncocked position. Disconnect the battery
from the trap.
WARNING: FAILURE TO FOLLOW SAFETY RULES CAN RESULT IN SERIOUS
INJURY OR DEATH!
Cocked Arm Position
(Ready to Launch Target)
Uncocked Arm Position
(Ready to Load Targets)
Circuit Breaker
ON/OFF/SAFE RELEASE
Switch
Drop Hole Open
Drop Hole
Partially Closed
2.5” to 4.5“
more than
4.5“
Flight Rail
4
III. Assembly
1. Unpacking
1. Carefully inspect the carton and trap machine to be sure that damage hasn’t
occurred during shipping. Report any damage found immediately to the
shipper.
2. Carefully remove trap assembly and all other components from cardboard
shipping box and other smaller boxes. Remove all hardware from bags.
3. Check that all parts were included. If any parts are missing, call the
CHAMPION Customer Service Department at (800) 379-1732 to obtain-
replacement parts.
4. Save all packing material and box if trap should ever need to be returned for
service or replacement.
5
2. Contents
F1 - Axle
F3 - Handle
F2 - Bracket Support Bar
F4 - 8mm x 45mm Bolt (4)
F5 - 8mm x 16mm Bolt (2)
F6 - 8mm Washer (12)
F7 - 8mm Lock Nut (6)
F8 - Plastic Wheel (2)
F9 - Large Axle Washer (4)
F11 - Mounting Bracket
F10 - Axle Clip (2)
F12 - 10mm x 16mm Bolt (4)
F13 - 10mm Washer (4)
Frame Parts
F12
F13
F11
F1
F9
F8
F7
F6
F5
F4
F3
F2
F10
Trap Assembly
6
S1 - Mainspring
A1 - Arm Path Tube
Supports (2)
M1 - Magazine Rods (4)
M2 - Magazine Top Plate
M3 - 5mm x 10mm Screws (4)
S2 - Mainspring Bolt
S3 - 10mm Flat Washer
S4 - 10mm Flange Nut
S5 - 10mm Hex Nut
A2 - Arm Path Tube
Studs (2)
A3 - Arm Path Tubing
A4 - 5mm x 10mm Screws (4)
A5 - 5mm Washers (4)
Mainspring Assembly
Parts
Arm Path Tubing Parts
Magazine Parts
S2
S5
S4
S3
S1
A4
A5
A1
A3
A2
M1
M3
M2
7
3. Assembly
Caution: Provide ample clearance around the trap.
DO NOT OPERATE THE TRAP IN AN AREA THAT DOES NOT ALLOW SAFE
(REAR) ACCESS TO THE TRAP AND THE ON/OFF/SAFE RELEASE SWITCH
DURING LOADING AND USE.
A. Assemble Frame
1. Assemble F1 (Axle) and F2 (Bracket Support Bar) to F11 (Mounting Bracket) using F4
(8mm x 45mm Bolt), F5 (8mm x 16mm bolt) with F6 (8mm Washers) and F7 (8mm Nut).
2. Attach F3 (Handle) to F2 (Bracket Support Bar) using F4 (8mm x 45mm Bolt) with F6 (8mm
Washers) and F7 (8mm Nut). F3 Handle end can point back or to the left as shown.
3. Assemble F8 (Plastic Wheel) to each end of F1 (Axle) with F9 (Large Axle Washer) on
each side of wheel. Install F10 (Axle Clip) in groove on each end of Axle.
F2
F1
F3
F3
F11
F8
F8
F5
8
B. Attach Trap to Frame
1. Stand and support trap assembly on front panel as shown.
2. Attach F11 (Mounting Bracket) to trap using F12 (10mm x 16mm Bolt) and F13 (10mm
Washer) as shown.
3. Pivot trap and frame back when finished.
F12
F13
Indice
