Channel Safety Systems ENTRitech Manuale utente
DDV INSTALLATION GUIDE | 1/1
CHANNEL SAFETY SYSTEMS t: 0845 884 7000 | w: www.channelsafety.co.uk
Digital Door Viewer Installation Guide
CHANNEL SAFETY SYSTEMS t: 0845 884 7000
Peterseld Business Park f: 0845 884 6000
Bedford Road
Peterseld
Hampshire e: sales@channelsafety.co.uk
GU32 3QA w: www.channelsafety.co.uk
The new digital door viewer from
Channel Safety Systems
R
Digital Door Viewer
DDV INSTALLATION GUIDE | 1/2
CHANNEL SAFETY SYSTEMS t: 0845 884 7000 | w: www.channelsafety.co.uk
CONTENTS
1. Parts ................................................................................................................... 2
2. Installation......................................................................................................... 3-
3. Operations......................................................................................................... 7
3.1. Buttons......................................................................................................... 7
3.2. Screen Shots................................................................................................. 7
3.1. Device Timing Operation..............................................................................7
PARTS
1 Main Unit (Screen)
2 Doorbell Unit (Camera)
3 Metal Tube
4 Back Plate
5 Adhesive Backing for Doorbell Unit
6 128mb microSD card (Pre-Installed)
7 1 Short Screw
8 2 Long Screws
9 Flat Tool
1
2
3
45
6789
DDV INSTALLATION GUIDE | 1/3
CHANNEL SAFETY SYSTEMS t: 0845 884 7000 | w: www.channelsafety.co.uk
INSTALLATION
1. Remove the current peep hole from your door. if you haven’t already got a peep hole, drill a 5/8”inch
hole.
2. Peel of the adhesive cover on one side of the Adhesive tape and attach to
the back of the Doorbell Unit.
The peel off the other adhesive cover
DDV INSTALLATION GUIDE | 1/4
CHANNEL SAFETY SYSTEMS t: 0845 884 7000 | w: www.channelsafety.co.uk
3. Securely place the Doorbell unit on the outside of the door using the Adhesive tape, insuring that the
metal threading is exactly in the middle of the peep hole.
4. Be sure that the connection ribbon comes all the way through the hole.
DDV INSTALLATION GUIDE | 1/5
CHANNEL SAFETY SYSTEMS t: 0845 884 7000 | w: www.channelsafety.co.uk
5. Peel off the tape backing on the back side of the Mounting plate, this will help prevent scratching on
your door when attaching the main unit. Then place the backing unit against the door and pull the
connection ribbon through the centre hole.
The circuit board goes in the right corner.
Now pull the connection ribbon through the metal tube, using the Flat tool provided, twist the metal
tube clockwise until it is firmly in place.
Circuit board
DDV INSTALLATION GUIDE | 1/6
CHANNEL SAFETY SYSTEMS t: 0845 884 7000 | w: www.channelsafety.co.uk
6. Snap the PCB to the connection point.
7. Use a screw driver not included) to help remove the faceplate from the main unit.
Install two AA batteries into the unit (not included).
DDV INSTALLATION GUIDE | 1/7
CHANNEL SAFETY SYSTEMS t: 0845 884 7000 | w: www.channelsafety.co.uk
8. Place the unit on the door so that the two ports securely connect, insure that the unit is properly
connected
For the following steps, please note that the main connection points are vital to the Digital Door
Viewer’s operation.
If they are not properly connected, the device will not work.
ATTENTION
Back of Main Unit
DDV INSTALLATION GUIDE | 1/8
CHANNEL SAFETY SYSTEMS t: 0845 884 7000 | w: www.channelsafety.co.uk
8. Use a Philips head screw driver (not included) along with the 2 long screws included to mount the
unit to the backing plate in two locations.
Replace the cover on the front of the device and using the 1 short screw to secure the faceplate to
the device.
Screw locations
DDV INSTALLATION GUIDE | 1/9
CHANNEL SAFETY SYSTEMS t: 0845 884 7000 | w: www.channelsafety.co.uk
The Digital Door Viewer is now fully installed.
Please note that both the screen and camera lens may have a clear plastic cover to
prevent scratching.
Please remove the plastic after installation.
DDV INSTALLATION GUIDE | 1/10
CHANNEL SAFETY SYSTEMS t: 0845 884 7000 | w: www.channelsafety.co.uk
OPERATIONS
Replacing the Batteries
To replace the batteries simply remove the faceplate of the main unit by unscrewing the bottom
screw of the device.
Remove the old batteries and replace them with two new AA batteries.
Refer to step 7 in the installation guide for more help.
Removing the mircoSD card
Remove the faceplate of the main unit by unscrewing the bottom screw on the device. Remove the
batteries from their position, push the microSD card in to release it. You can now view the images
from the card on another device or replace the microSD card with more/less memory.
Digital Door Viewer Diagram
Altri manuali per ENTRitech
2
Indice
Altri manuali Channel Safety Systems Sistema di sicurezza
Manuali Sistema di sicurezza popolari di altre marche
EDM
EDM Solution 6+6 Wireless-AE Manuale utente
Highway Safety Group
Highway Safety Group EA401 Manuale utente
Siren
Siren LED GSM Manuale utente
Detection Systems
Detection Systems 7090i Istruzioni per il montaggio
Se-Kure Controls
Se-Kure Controls MicroMini SK-4841 Manuale utente
Siemens
Siemens FDM273 Manuale utente