Charnwood BD46 Manuale utente
GENERAL SAFETY RULES
WARNING: Do not attempt to operate the machine until you have read thoroughly and
understood completely all instructions, rules, etc. contained in this manual. Failure to comply
may result in accidents involving fire, electric shock, or serious personal injury. Keep this
owner's manual and review frequently for continuous safe operation.
1. Know your machine. For your own safety, read the owner's manual carefully. Learn its application and
limitations, as well as specific potential hazards pertinent to this machine.
2. Make sure all tools are properly earthed.
3. Keep guards in place and in working order. If a guard must be removed for maintenance or cleaning,
make sure it is properly replaced before using the machine again.
4. Remove adjusting keys and spanners. Form a habit of checking to see that the keys and adjusting
spanners are removed from the machine before switched it on.
5. Keep your work area clean. Cluttered areas and workbenches increase the chance of an accident.
6. Do not use in dangerous environments. Do not use power tools in damp or wet locations, or expose
them to rain. Keep work areas well illuminated.
7. Keep children away. All visitors should be kept a safe distance
8. from the work area.
9. Make workshop childproof. Use padlocks, master switches and remove starter keys.
10. Do not force the machine. It will do the job better and be safer at the rate for which it is designed.
11. Use the right tools. Do not force the machine or attachments to do a job for which they are not
designed. Contact the manufacturer or distributor if there is any question about the machine's suitability for
a particular task.
12. Wear proper apparel. Avoid loose clothing, gloves, ties, rings, bracelets, and jewellery which could get
caught in moving parts. Non-slip footwear is recommended. Wear protective hair covering to contain long
hair.
13. Always use safety glasses. Normal spectacles only have impact resistant lenses. They are not safety
glasses.
14. Do not over-reach. Keep proper footing and balance at all times.
15. Maintain the machine in good condition. Keep the machine clean for best and safest performance.
Follow instructions for lubrication and changing accessories.
16. Disconnect the machine from power source before servicing and when changing the blade.
17. Never leave the machine running unattended. Turn the power off. Do not leave the machine until it
comes to a complete stop.
18. Do not use any power tools while under the effects of drugs, alcohol or medication.
19. Always wear a face or dust mask if operation creates a lot of dust and/or chips. Always operate the tool
in a well ventilated area and provide for proper dust removal. Use a suitable dust extractor.
Risk of Injury. Wear Eye Wear Ear
Never reach into Protection Protection
a moving part
BD46 Belt & Disc Sander Overview
Sanding Belt
Tracking Adjuster
Sanding Belt
Tension Lever
Sanding Disc Sanding Belt Stop
Sanding Table
Mitre Fence Belt Angle Lock
On Off Switch
Rubber Feet
Table Angle Lock
Specification
Disc Diameter
150mm (6”)
Disc Speed
2850rpm
Belt Size
100mm x 915mm (4” x 36”)
Belt Speed
550m/min
Motor (Induction) 240v 50hz
450w (0.6hp)
Dust Extraction Port Diameters (Belt & Disc)
37mm External / 31mm Internal
Weight
14kg
Manufacturer’s Warranty
1 year
Rating
Hobby
Rating Description
Hobby: Suitable for Weekend DIY'ers and woodworking enthusiasts.
Generally lighter weight machines with lower power ratings and smaller tooling capacities. Typically only
ever used by one person for short periods of time or longer periods of time infrequently. Machinery should
be well maintained in a clean, dry environment such as a home workshop, garage or timber shed.
Expected maximum use of 100 hours annually.
Please Note: Using a product in excess of its rating will void the manufacturer’s free warranty.
Unpacking
All items are contained in one carton.
Carefully unpack and check that all the
items are present.
Assembly
Place the sander on a flat surface.
Use a 14mm spanner to adjust the
supporting leg so that the belt bed is
horizontal.
To do this you might need to loosen the
hex
head bolt which clamps the bed in
position.
The table can be fitted in either of two
positions, depending upon whether you
are using the sanding disc or the sanding
belt.
To attach the table when using the
sanding disc:
Locate the table bracket into the curved
slot next to the disc.
Fix in place using the clamping screw &
washer provided.
Adjust the angle of the table using a set
square so that it is at right angles to the
disc.
Ensure that the gap between table & disc
is no more than 1.6mm. This will prevent
fingers from becoming trapped when
sanding.
Tighten the clamping screw.
Use a cross head screwdriver to adjust
the red pointer to ‘0’ degrees against the
scale.
Pointer
Locking screw
The sanding belt can be used in the
vertical or horizontal position - or any
angle in between.
When using the belt sander, either the
back stop or the sanding table must be
fitted.
The back stop is attached using the two
socket head screws and washers
provided.
Adjust the stop so that there is a
maximum gap of 1.6mm to the belt.
To adjust the angle of the sanding belt:
Loosen the hex socket clamping bolt
Lift the sanding belt into the vertical
position.
Re-tighten the bolt.
Remove the back stop.
Fit the sanding table in the same manner
as when using it with the sanding disc.
Secure using the clamping screw/washer.
Adjust the table so that it is at 90 degrees
to the belt.
Ensure a maximum gap of 1.6mm.
Adjust the red pointer so that it indicates
‘0’ degrees against the scale.
Pointer
Locking screw
The mitre guide is fitted to the slot in the
table.
It can be adjusted to any angle in a 120
degree range.
It is used to guide the work piece and
give an accurate angle.
It is advisable to use dust extraction when
using your sander. There are separate
extraction ports for the belt and disc with
an outside diameter of 37mm.
An appropriate adapter may be required.
Setting Up
Tracking the belt
Ensure the machine is disconnected from
the power supply.
Slowly rotate the belt by hand in the
direction shown.
If the belt is moves off to one side it
requires a tracking adjustment.
If the belt stays central it is already
correctly tracked.
Viewed from the switch end –if the belt
moves sideways towards the disc, turn
the tracking knob clockwise (1/4 turn is
usually sufficient).
If the belt moves sideways away from the
disc, turn the knob anti-clockwise.
Continue adjustments until the belt
remains central on the rollers.
Tracking knob.
Using the Sander
This sander is designed for use with wood and wood-based products only. It should not be used for
sanding metal and any such use would invalidate the warranty.
The machine should be placed on a firm level surface before use.
Sanding with the belt in the horizontal
position
The work table or back stop must always
be used as a support when carrying out
edge or face sanding in the horizontal
position.
Move the workpiece across the belt while
keeping one edge against the stop.
Do not use excessive pressure and take
extra care when sanding thin material.
Sanding internal curves
With care the idler drum end of the
sanding belt can be used for smoothing &
shaping the inside of curved workpieces.
Never present the end of a workpiece to
the drum as this can cause it to kick
back.
Indice
Altri manuali Charnwood Levigatrice
Charnwood
Charnwood DS10 Manuale utente
Charnwood
Charnwood W409 Manuale utente
Charnwood
Charnwood W408 Manuale utente
Charnwood
Charnwood W413 Manuale utente
Charnwood
Charnwood W413 Manuale utente
Charnwood
Charnwood BD15 Manuale utente
Charnwood
Charnwood BD610 Manuale utente
Charnwood
Charnwood BD48 Manuale utente
