Checkpoint ATP Series Scheda tecnica

QUICK SETUP

Series ATP

www.cppumps.com

Tool Requirements

Hex Wrenches: 1/8”, 5/32”, 3/16”

Open-End Wrenches: 7/16”, 5/8”, 7/8”, 1”

Leg Assembly and Pump Attachment

1. Unpack pump stand assembly, and ensure that all pieces are

supplied.

2. Place pump bracket (ATP0090-01) onto both legs. The four holes

near the edge of the bracket are located between the two legs (as

shown below).

3. Install the two rear bolts with washers through the pump bracket and

legs of the pump stand, and tighten the hex nuts.

PART #

DESCRIPTION

QTY.

ATP0090-01

PUMP BRACKET

HHBS8042028

HEXHEAD BOLT

HHNIS80420

HEX NUT

HWSHS804

FLAT WASHER

PST0002-1

LEG –SOLAR

WARNING: Ensure that you are wearing proper PPE before performing any action.

WARNING: Pinch points. Disconnect power before removing cover.

4. Remove the front cover from the pump drive.

5. Set the pump on the stand such that the four carriage-assembly bolt-

heads line up in the stand clearance holes. Install the two front bolts

with washers from the underside of the pump through the legs and

into the pump drive housing, and tighten hex nuts.

6. Connect the suction line to the bottom check valve, and connect the

discharge line to the top check valve.

CP-QS-ATP

REV00 EFF. DATE: 1/9/2019

Page 1 of 2

QUICK SETUP

Series ATP

www.cppumps.com

Chemical Flow Rate Adjustment

7. Loosen the lock screw on the adjustment block. Using the supplied adjustment tool, turn the adjustment nut to increase or

decrease the flow rate to the desired percentage, as indicated by the markings (refer to the flow charts to estimate position

based on your application).

CAUTION: Do not turn the adjustment nut to apply force below the 0% or above the 100% mark.

8. Re-tighten the lock screw on the adjustment block.

9. Reinstall the pump cover.

10. Connect the pump to the electrical service.

CAUTION: Ensure that the power source does not exceed the rating for the pump motor.

11. With fluid media present at the pump suction, loosen the bleed screw and discharge line at the discharge check outlet to

vent to atmosphere. Run the pump until all air trapped in the head is released. Stop the pump.

Re-tighten the discharge line and bleed screw.

12. Run a drawdown flow calibration. If the flow rate is correct, stop here. If the flow rate requires adjustment, continue.

13. Disconnect the power.

WARNING: Pinch points. Disconnect power before removing cover.

14. Remove the pump cover.

15. Return to Step 7. Repeat these steps until the target flow rate is achieved.

CP-QS-ATP

REV00 EFF. DATE: 1/9/2019

Page 2 of 2

Altri manuali per ATP Series

Indice

Altri manuali Checkpoint Pompa dell'acqua

Checkpoint

Checkpoint 6200 Series Manuale utente

Checkpoint

Checkpoint 5400 Series Manuale utente

Checkpoint

Checkpoint SLA Series Scheda tecnica

Checkpoint

Checkpoint 1250 Series Manuale utente

Checkpoint

Checkpoint 1250E Series Manuale utente

Checkpoint

Checkpoint ATP3 Series Manuale utente

Checkpoint

Checkpoint SLA Series Manuale utente

Checkpoint

Checkpoint GX15G11C3 Series Manuale utente

Checkpoint

Checkpoint ATP Series Manuale utente

Manuali Pompa dell'acqua popolari di altre marche

Neptun

Neptun NPHW 5500 Manuale utente

Sensidyne

Sensidyne Gilian BDX-II Istruzioni per l'installazione e il funzionamento

Draper

Draper 47808 Manuale utente

Trolla

Trolla 12820 Manuale utente

Sunfab

Sunfab SVH Series Manuale utente

WilTec

WilTec 50740 Manuale utente

Fieldmann

Fieldmann FVC 5015 EK Manuale utente

Everbilt

Everbilt EFSUB5-122HD Manuale utente

Graco

Graco Husky 3300e Manuale utente

esotec

esotec 101018 Manuale utente

moyno

moyno 2000 CC Manuale utente

Becker

Becker BASIC VASF 2.80/1-0.AC230 Manuale utente

Sykes AmeriPumps

Sykes AmeriPumps GP100M Guida alla risoluzione dei problemi

DUROMAX

DUROMAX XP WX Series Manuale utente

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Manuale utente

Franklin Electric

Franklin Electric IPS Manuale utente

Xylem

Xylem e-1532 Series Manuale utente

Milton Roy

Milton Roy PRIMEROYAL Manuale utente