CHERUBINI META Smart Plug Manuale utente

DRAFT

ISTRUZIONI - INSTRUCTIONS - EINSTELLANLEITUNGEN

INSTRUCTIONS - INSTRUCCIONES

Presa intelligente

Smart plug

Prise intelligente

Enchufe inteligente

META

Smart Plug

TRANSLATION OF THE ORIGINAL INSTRUCTIONS

Index:

Device description ................................................................................................. p. 14

Technical specications.......................................................................................... p. 15

LED status indicator .............................................................................................. p. 16

META Smart Plug activation .................................................................................. p. 16

Including (Add) the device into an existing Z-Wave network ................................ p. 16

Excluding (Remove ) the device from a Z-Wave network ...................................... p. 16

Controlling the device............................................................................................ p. 17

Controlling the load through the Smart Plug....................................................... p. 17

Controlling the device through Z-Wave network................................................. p. 17

Reset to factory settings ........................................................................................ p. 17

Firmware update ................................................................................................... p. 17

Electric parameters reading ................................................................................... p. 17

Overvoltage and overcurrent alarms ..................................................................... p. 17

Associations .......................................................................................................... p. 18

Congurations ....................................................................................................... p. 19

Supported command classes ................................................................................. p. 22

EU declaration of conformity

CHERUBINI S.p.A. declares that the product is in conformity with the relevant Union

harmonisation legislation: Directive 2014/53/EU, Directive 2011/65/EU.

The full text of the EU declaration of conformity is available upon request at the following

website: www.cherubini.it.

Failure to comply with these instructions annuls CHERUBINI’s responsibilities and

guarantee.

The crossed-out wheelie bin symbol indicates that the product must be collected

separately from other waste at the end of its useful life. Therefore, users should

deliver this product to appropriate waste collection points or return it to their

dealers at the end of its service life. See your local authority’s regulations.

Adequate waste sorting for subsequent processing and environmentally compatible

disposal helps to avoid possible negative effects on the environment and public health

and promotes reuse and/or recycling of the materials used to make the equipment.

ENGLISH

META Smart Plug is able to detect overvoltage and/or overcurrent events and indicate

them through a multicolor LED. Furthermore, it protects appliances from eventual

overload. A very innovative design, which integrates a complex system that allows a

precise energy consumption monitoring. The integration of these features in its very

small size product, make it unique on the market.

The device is equipped with contact protection technology (Zero Crossing) which

reduces the electrical stress on the relay contacts and ensures a longer life. The open /

closed switching of the device always occur when the instantaneous value of voltage

is 0.

It operates in any Z-Wave network with other Z-Wave/Z-Wave Plus certied devices and

controllers from any other manufacturer. As a constantly powered node, WiDom Smart

Plug will act as repeater regardless of the vendor in order to increase the reliability of

the network.

Load control functionality Switching the relay

Z-Wave functionality 3 clicks including the device in the Z-Wave Network;

3 clicks removing the device from the Z-Wave Network;

Meter functionality Manual reset of alarms

DEVICE DESCRIPTION

Push Button

ENGLISH

TECHNICAL SPECIFICATIONS

Power Supply 230 VAC ± 10% 50/60 Hz

Maximum Load on Relay 2800 VA – 230 VAC – 12A

Temperature limitation 105 °C

Work Temperature From -10° to 40° C

Power consumption < 0.4 Watt

Radio frequency 868.4 MHz

Protection system S0 and S2 Security

Maximum distance Up to 100 m outdoor

Up to 40 m indoor

Dimensions (HxWxD) 69x44x44 mm

Actuator element Relay

Compliance CE, RoHs

Electrical IP Rating IP20

Meter Specications

Parameters Voltage RMS, Active Power, Energy

Meter Range Voltage RMS: 250 V

Active Power: 2500 W

Energy: 2.000.000 kWh

Resolution Voltage RMS: 0.1 V

Active Power: 0.01 W

Energy: 0.001 kWh

Maximum Error Voltage RMS: 2 Volt

Active Power: 0.5 Watt

ENGLISH

The system includes an RGB LED that shows the device’s status during the installation

procedure:

One single BLUE blink: when connecting to the power supply and the device is not yet

included in the Z-Wave network

OFF: the relay is OFF

Solid GREEN: the relay is ON

Blink GREEN - BLUE: Learn mode for Inclusion and Exclusion

Blink GREEN: the device is indicating Overcurrent event

Blink BLUE: the device is indicating Overvoltage event.

1) Connect the device to a power outlet

2) Include the device in the Z-Wave network.

LED STATUS INDICATOR

META SMART PLUG ACTIVATION

META Smart Plug is compatible with all Z-Wave/Z-Wave Plus certied controllers. The

device supports both the

Network Wide Inclusion

mechanism (which offers the ability to

be included in a network, even if the device is not directly connected to the controller)

and

Normal Inclusion

If the device is not included into a Z-Wave network, three consecutive clicks on the Push

Button will launch the process of traditional inclusion. If the device inclusion procedure

does not start within 2 seconds, the Network Wide Inclusion network will be launched

and will last between 15-30 seconds.

The procedure of inclusion is started from the gateway control interface and by

performing 3 consecutive clicks on the integrated button.

INCLUDING (ADD) THE DEVICE INTO AN EXISTING Z-WAVE

NETWORK

Only a controller can remove a device from the network. After activating the exclusion

function by the controller, the device can be removed by setting it in Exclusion Mode by

three consecutive clicks on the Push Button.

At this point, the LED indicator starts a sequence of GREEN-BLUE blinks until the end of

the process of Exclusion.

EXCLUDING (REMOVE) THE DEVICE FROM A Z-WAVE NETWORK

ENGLISH

Controlling the load through the Smart Plug

A single click or two clicks on the Push Button can turn ON/OFF the load (Parameter

No. 1).

Controlling the device through Z-Wave network

META Smart Plug can be controlled by any Z-Wave / Z-Wave Plus certied controller

available in the market.

All Z-Wave controllers can control the device by using the

Basic Set

command.

CONTROLLING THE DEVICE

The device can be reset to the original factory settings by removing the device from

the Z-Wave Network.

The system supports over-the-air rmware updates that do not require the device to

be removed from its location. The rmware update can be activated from all certied

controllers supporting version 2 of the Firmware Update function.

META Smart Plug can read the Active Power, the Voltage RMS and the Energy

consumed by the load. These values can be obtained through the certied controllers

that support the Meter Command Class version 3.

META Smart Plug is able to detect overvoltage and overcurrent events, and show them

through a blinking LED:

•

Blink GREEN

– Overcurrent event

•

Blink BLUE

– Overvoltage event

These events generate alarms that can control associated devices, by sending Basic Set

Commands, and open the relay in case of the overcurrent alarm.

RESET TO FACTORY SETTINGS

FIRMWARE UPDATE

ELECTRIC PARAMETERS READING

OVERVOLTAGE AND OVERCURRENT ALARMS

WARNING: The system will be rebooted at the end of the rmware update

procedure. If the load is ON it will be turned OFF and then again ON.

It is advisable to carry out the rmware update procedure only when necessary.

ENGLISH

ASSOCIATIONS

META Smart Plug can control, through direct association, other devices of the Z-Wave

network in which is included, when an event of overcurrent, overvoltage or events on

the Push Button occur.

META Smart Plug can control devices such as relays or dimmers. META Smart Plug

supports 5 association groups, each of which supports the association of up to 8 devices:

1-Lifeline: Nodes belonging to this groups will receive changes related to the relay

status and power consumption;

2-Over Current: Nodes belonging to this groups will be controlled by a basic set if

over current event occurs;

3-Over Voltage: Nodes belonging to this groups will be controlled by a basic set if

over voltage event occurs;

4-Control 1 Click: Nodes belonging to this groups will be controlled by a basic set if

the button receives one click:

5-Control 2 Clicks: Nodes belonging to this groups will be controlled by a basic set if

the button receives two clicks.

TIP: META Smart Plug can control up to 8 devices for every group. In order to

prevent the network from slowing down it is advisable to limit the associated

devices to no more than 5 per group.

ENGLISH

CONFIGURATIONS

Controlling the associated devices

ITALIANO

Parameter No. 1: Local load control (1 Byte)

Denes which sequences of clicks control the local load.

Parameter No. 2: Level used to control the devices associated to group 4 (1 Byte).

Denes how to control the devices associated to 1 click event.

Parameter No. 3: Level used to control the devices associated to group 5 (1 Byte).

Denes how to control the devices associated to 2 clicks event.

Conguration Result

1ONE_CLICK

1 click turn ON/OFF the local load

2TWO_CLICKS

2 clicks turn ON/OFF the local load

(Default Value)

ONE_CLICK or TWO_CLICKS

1 click or 2 clicks turn ON/OFF the local load

Conguration Result

0SWITCH_OFF

The associated devices are switched OFF

-1 SWITCH_ON

The associated devices are switched ON

1 - 99 LEVEL

The associated devices are set to the indicated level

100

(Default Value)

RELAY_STATUS

If the relay is ON/OFF, the associated devices are ON/OFF

Conguration Result

0SWITCH_OFF

The associated devices are switched OFF

-1 SWITCH_ON

The associated devices are switched ON

1 - 99 LEVEL

The associated devices are set to the indicated level

100

(Default Value)

RELAY_STATUS

If the relay is ON/OFF, the associated devices are ON/OFF

ENGLISH

Overvoltage Alarm

Parameter No. 4: Overvoltage level (2 Byte).

Denes the voltage level (in Volts) beyond which an overvoltage event is identied and

the overvoltage timer is activated.The timer is reset when the event ceases, i.e. when the

voltage returns below the overvoltage level. As soon as an overvoltage event occurs, the

LED starts a BLUE blinking. If the overvoltage event ceases before the overvoltage timer

expires, the blue blinking is stopped, otherwise the alarm is generated and the blinking

reset is established by parameter 6.

Parameter No. 5: Overvoltage Timer (2 Byte).

Denes the time (seconds) in which the voltage must persist above the overvoltage level

so that an alarm is generated.

Parameter No. 6: Overvoltage Alarm Reset (1 Byte).

Denes how to reset the overvoltage alarm and breaks off the blue blinking.

Parameter No. 7: Level used to control the devices associated to group 3 (1 Byte).

Denes how to control the devices associated to the overvoltage alarm.

Conguration Result

110 - 260

253 (Default Value) Denes the overvoltage level (in Volts)

Conguration Result

1 - 3600

5 (Default Value)

Overvoltage time interval (in seconds) after which an alarm is

generated

Conguration Result

(valore di Default)

MANUALE

When the relay change its state through the Push Button

1OVER_VOLTAGE_END

When the overvoltage event is terminated

Conguration Result

(Default Value)

SWITCH_OFF

The associated devices are switched OFF

-1 SWITCH_ON (Acceso)

The associated devices are switched ON

1 - 99 LEVEL

The associated devices are set to the indicated level

ENGLISH

Indice

Altri manuali CHERUBINI Domotica

CHERUBINI

CHERUBINI A510068 META Manuale utente

Manuali Domotica popolari di altre marche

Truth Hardware

Truth Hardware Sentry II Manuale utente

FIBARO

FIBARO FGWPA-111 Manuale utente

Hezborg

Hezborg BGR8016B Manuale utente

MYDLINK

MYDLINK Pro Series Manuale utente

Panasonic

Panasonic KX-HNA101FX Manuale utente

GamaBit

GamaBit Houseper Manuale utente

nedis

nedis WIFILRF10C37 Manuale utente

Veho

Veho TA45 Manuale utente

Nexa

Nexa ZPR-111 Manuale utente

Vimar

Vimar 00801 Manuale utente

Leviton

Leviton 47604-F6 Manuale utente

EVERSPRING

EVERSPRING AN180 Manuale utente

Coltech

Coltech 18-1339 Manuale utente

IDS

IDS NXT vegas Guida

Vimar

Vimar 03975 Manuale utente

iNels

iNels RFIM-20B Manuale utente

EVA Logik

EVA Logik ZW30 Manuale utente

Leviton

Leviton ODCØP-S0W Manuale utente