Chiayo RR-2000 Manuale utente

RR-2000

RCC-2000

Extra Long Range (XLR) Wireless Microphone System

ISO 9001

ISO 14001

OHSAS 18001

GREEN PRODUCT

Operation manual

ISO

14001

REGISTERED

INTERNATIONAL

OHSAS

18001

REGISTERED

INTERNATIONAL

Thank you and congratulation for purchasing CHIAYO’s professional XLR (Extra Long Range)

cellular concept multi-diversity reception wireless microphone system. Please read this manual

thoroughly to familiarize with the function of each part before use.

BASIC CONCEPT

This system consists of two main parts:

1.Remote Control Center RCC-2000

2.Remote Receiver RR-2000

The Remote Control Center RCC-2000 is the nerve center of the whole system. It is capable of

controlling up to 4 units of Remote Receiver RR-2000, delivering power supply and receiving /

monitoring signal of the individual Remote Receiver via Cat 5e cable.

Each Remote Receiver RR-2000 has an antenna divider plus power distribution and is capable

of holding 2 diversity receiver module RR-2000M (CH A and CH B). An optional outdoor

waterproof mounting kit PRR-2000 is available for outdoor installation.

PARTS AND FUNCTIONS OF RCC-2000

►Front

1.Power switch.

2.RF signal indicator of the 2 remote receivers’ CH A and CH B

3.AF signal indicator of the 2 remote receivers’ CH A and CH B

4.LCD display

5.UP button

6.DOWN button

7.MENU button

8.SET button

►Rear

1.DC-input

2.Remote receiver ①connector (RJ-45 jack for CAT.5e)

3.Remote receiver ②connector (RJ-45 jack for CAT.5e)

4.Remote receiver ③connector (RJ-45 jack for CAT.5e)

5.Remote receiver ④connector (RJ-45 jack for CAT.5e)

6.Channel B balanced audio output (XLR)

7.Channel B unbalanced audio output (Ø 6.3mm)

8.Channel A balanced audio output (XLR)

9.Channel A unbalanced audio output (Ø 6.3mm)

12 3 45

234

ISO 9001｜ISO 14001｜OHSAS 18001

VARIOUS SETTINGS ON THE REMOTE CONTROL CENTER RCC-2000

■Adjusting the volume

1 Press MENU button to go to “VOLUME”page.



2 Hold SET to enter setting. Choose A or B by SET button, and UP/DOWN buttons to adjust

the volume. The setting will be automatically saved after five seconds.

choose Aor Badjust VOLUME

Warning: In order for this function to work correctly, the volume of the remote receiver module

side should be manually fixed at an appropriate level beforehand!

■Changing ON/OFF status of the remote receivers

1 Press MENU button to go to “R1-4”page.



2 Hold SET to enter setting. Choose R1/R2/R3/R4 B by SET button, and UP/DOWN buttons

to switch individual ON/OFF status of R1, R2, R3 and R4. The setting will be automatically

saved after five seconds.

choose R1/2/3/4 set ON/OFF status

Warning: This function is only possible when the remote receiver module is switched ON

beforehand!

SET

■Changing the frequency

1 Press MENU button to go to “CHANNEL/FREQUENCY”page.



2 Hold SET to enter setting. Choose A or B by SET button, and UP/DOWN buttons to change

the frequency. The setting will be automatically saved after five seconds and will be sent to

and shown at all the connected RR-2000M's 2-digit 7-segment LED display. CH A will be 01

and CH B will be 00 (for 100)

choose Aor Bchange FREQUENCY

The display value indicates the RF signal strength.

SET

Pointer ”” indicates which RR-2000’s module the audio comes

from. The item marked with “X

” is power off on either the module

itself or RCC-2000.

ISO 9001｜ISO 14001｜OHSAS 18001

PARTS AND FUNCTIONS OF REMOTE RECEIVER RR-2000

►Front

LEFT: channel A, RIGHT: channel B

1.Power switch.

2.7-segment LED display

3.Channel UP button

4.Channel DOWN button (RCC-2000has priority and overrides this button for channel number)

5.AF signal indicator

6.RF signal indicator

7.Module power/volume control

►Rear

1.Antenna A (TNC)

2.RJ-45 jack for CAT.5e cable

3.Antenna B (TNC)

■Channel name setting on the remote receiver RR-2000M

Each Remote Station RR-2000 can hold up to 2 units of RR-2000M receiver modules. The A

channel (CH A) is assigned on the left and the B channel (CH B) assigned on the right of this

rack. If this unit is connected to the RR1 RJ-45 connector of the RCC-2000, module A must be

set to A1 and module B to B1. If another RR-2000 is connected to the RR2 RJ-45 connector,

its module A must be set to A2 and module B set to B2. And so on.

RR2

RR1

RR4

RR3

3 4 5 6 7

123

To do the setting, first hold both UP and DOWN buttons till the LED flashes. Then press UP

button to select A or B and DOWN button to select 1/2/3/4.

Precisely, the two receivers of 1st RR-2000 should be named as A1 and B1, for 2nd as A2 and

B2, for 3rd as A3 and B3, for 4th as A4 and B4. This should be done so in accordance with the

preset programming in the Remote Control Center RCC-2000. (RCC-200 has priority and

overrides this button for channel number.)

After name setting, the LED will return back to the allocated channel number programmed at

the RCC-2000.

■Audio output connection

BALANCED output: XLR connector provides balanced audio output signal from this jack to the

mixer/amplifier. Use an audio output cable with “XLR” or “Cannon” connector, connect one end

to the balanced output jack of the receiver, and the other end to the “MIC IN” jack of the mixer/

amplifier.

UNBALANCED output: ¼” PHONE PLUG connector provides unbalanced audio output signal

from this jack to the mixer/amplifier. Use an audio output cable with ¼” PHONE PLUG

connectors. Connect one end from the unbalanced output jack of the receiver, and the other

end to the “LINE IN” jack of the mixer/ amplifier.

BALANCED audio connectionUNBALANCED audio connection

ISO 9001｜ISO 14001｜OHSAS 18001

■Installation

For best operation, the remote receiver RR-2000 should be at

least 1m above the ground and at least 1m away from a wall or

metal surface to minimize reflection. The transmitter should also

be at least 1m away from a wall or metal surface to minimize

reflection. The transmitter should also be at least 1m away from

the receiver.

■Mounting

Both the remote control center RCC-2000 and remote receiver RR-2000 have a half-19"-casing

design. They can be cabinet-mounted with either one or two units. Individual kits for mounting

one or two units are available and please refer to below assembly illustration.

Fig 1. Rack mount of one unit

Fig 2. Rack mount of two units

■Outdoor weatherproof mounting

Remote receiver RR-2000 can be mounted outdoor in a weatherproof casing PRR-2000 as

following:

►

HANDHELD TRANSMITTER SQ-6100/SQ-7100

Microphone parts and functions

SQ-6100

SQ-7100

Cartridge

Battery weak/power LED

Power switch

LCD

Battery compartment

Bottom cap

Locking button

Audio mute switch

Setting button

Up button

Down button

Charging port

■Battery installation & indicator

This transmitter requires 2 x AA batteries to operate.

To install, remove the battery cover and slide the batteries into the battery compartment &

replace the battery cover.

Note: Batteries contain a corrosive acid that may leak and damage the transmitter when stored

for a long period. Batteries should be removed from the transmitter before storing without use

for more than 4 weeks.

When the transmitter is switched ON, a red LED②will blink once to indicate the batteries

installed are in good condition. If the LED remains illuminated, it means the batteries are

weak and require replacement.

■Channel setting

Use UP or DOWN button to go to the CHANNEL/ FREQUENCY page.

The cursor will flash to allow changes to be made. Pressing UP or DOWN button will increase

or decrease the channel number. The corresponding frequency will change accordingly. When

a desired channel is selected, it will be automatically saved and stored in the memory.

1 2 3 4 5 6 91011

7 8

ISO 9001｜ISO 14001｜OHSAS 18001

■Making changes to battery selection

Use UP or DOWN button to go to the Battery selection page.

Press UP or DOWN button to move the cursor to either NiMH (rechargeable battery) or

AKLN (Alkaline battery) position.

When the desired battery has been selected, it will be automatically saved and stored in the

memory.

Remark: NiMH battery must be selected when rechargeable battery is being used. Never

select AKLN (alkaline) when transmitter is intended for charging as alkaline battery isn’t

rechargeable. Wrong battery selection will result in battery sensing electronics to display wrong

and misleading status information.

■Making changes to sensitivity level

Use UP or DOWN button to go to the SENS SET page.

Press UP or DOWN button to increase or decrease the Sensitivity Level of the microphone.

The MAX level is 4and the MIN level is 1.When a desired sensitivity level has been selected

for your application, it will be automatically saved and stored in the Memory.

Remark: When selecting Sensitivity level, please bear in mind that Level 1 is for close

proximity singing purposes whereas Level 4 is for use of microphone on tripod mount for

speech purposes. When Level 4 setting is used for close proximity singing, high SPL input will

result in undesirable distortion in the output.

After performing setting changes, you could turn the protective cover 180°in either direction to

block the buttons from being accidentally adjusted.

BELT-PACK TRANSMITTER SM-7100

■Parts and functions

1.Antenna

2.Battery weak/audio mute indicator

3.Audio mute switch

4.(Lavalier microphone) Mini XLR connector

5.LCD

6.Charging port

7.Cover release button

8.Power switch

9.Gain control (GT, high impedance)

10.Gain control (MT, low impedance)

11.Setting button

12.Up button

13.Down button

14.Battery compartment

15.Charging contacts

■Battery installation & indicator

This belt-pack requires 2 x AA batteries to operate.

To install, open the battery cover using the cover release buttons and insert the batteries into

the battery compartment.

Note: Batteries contain a corrosive acid that may leak and damage the belt-pack when stored

for a long period. Batteries should be removed from the belt-pack before storing without use for

more than 4 weeks.

When the transmitter is switched ON, the battery power LED②will blink once to indicate the

batteries installed are in good condition. If the LED remains illuminated the batteries have

expired and require replacement.

■Channel setting

Use UP or DOWN button to go to the CHANNEL/ FREQUENCY page.

The cursor will flash to allow changes to be made. Pressing UP or DOWN button will increase

or decrease the channel number. The corresponding frequency will change accordingly. When

a desired channel is selected, it will be automatically saved and stored in the memory.

234

15 15

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Chiayo Sistema microfonico

Chiayo

Chiayo Smart 300 Manuale utente

Chiayo

Chiayo R-1001 Manuale utente

Chiayo

Chiayo Q-818 Manuale utente

Chiayo

Chiayo DH2400 Manuale utente

Chiayo

Chiayo UDR-500 Manuale utente

Chiayo

Chiayo AIR-812 Manuale utente

Chiayo

Chiayo QR-4000N Manuale utente

Chiayo

Chiayo SQ-6100 IrDAR Manuale utente

Chiayo

Chiayo IRX2 Manuale utente

Chiayo

Chiayo IWM-202 Manuale utente

Chiayo

Chiayo SDR-6200 IrDA Manuale utente

Chiayo

Chiayo QR-4000 U Manuale utente

Chiayo

Chiayo Live-100 series Manuale utente

Chiayo

Chiayo Q-200 Manuale utente

Chiayo

Chiayo IWR-320 Manuale utente

Chiayo

Chiayo SDR-5216 Manuale utente

Chiayo

Chiayo SDR-6200 IrDA Manuale utente

Chiayo

Chiayo NDR-3100 Manuale utente

Chiayo

Chiayo IRX2 Manuale utente

Chiayo

Chiayo R-1001 Manuale utente

Chiayo

Chiayo R-1010 Manuale utente

Chiayo

Chiayo Artist Manuale utente

Chiayo

Chiayo SDR-8200 Manuale utente

Chiayo

Chiayo IrDA-9000 Manuale utente

Manuali Sistema microfonico popolari di altre marche

Paso

Paso R824 Manuale utente

Naxa

Naxa NAM-982 Manuale utente

Motorola

Motorola PMNN4461 Manuale utente

Xvive

Xvive U3 Manuale utente

Tekon

Tekon DUOS Manuale utente

Heyuan Intelligence

Heyuan Intelligence IOT-G2S-01 Manuale utente

Devine

Devine WMD-IE Manuale utente

LG LF-D7150 Manuale utente

GE S768DAV Manuale utente

LD U305 HBH 2 Manuale utente

Chainway

Chainway URA8 Manuale utente

ORATOR

ORATOR D860TD Manuale utente

Sennheiser

Sennheiser Evolution Wireless Digital EW-DX EM 2 Manuale utente

Alpha Technologies

Alpha Technologies RBMS Manuale utente

SWIT Electronics Co.,LTD.

SWIT Electronics Co.,LTD. CW-S150 Manuale utente

Shure

Shure UA844 Manuale utente

Panasonic

Panasonic SHFX70 - DVD HOME THEATER WIRELESS SYSTEM Manuale utente

Pyle

Pyle PDWM5000 Manuale utente