Chicago Electric 66301 Istruzioni per l'installazione

ELECTRIC PAINT SHAKER

66301

ASSEMBLY, OPERATION, AND MAINTENANCE

INSTRUCTIONS

Distributed exclusively by Harbor Freight Tools®.

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit our website at: http://www.harborfreight.com

Read this material before using this product.

Failure to do so can result in serious injury.

SAVE THIS MANUAL.

contained herein may be reproduced in any shape or form without the express written consent of

Harbor Freight Tools. Diagrams within this manual may not be drawn proportionally. Due to continuing

improvements, actual product may differ slightly from the product described herein. Tools required for

assembly and service may not be included.

For technical questions or replacement parts, please call 1-800-444-3353.

SKU 66301 For technical questions, please call 1-800-444-3353. Page 2

SAVE THIS MANUAL

Keep this manual for the safety warn-

ings and precautions, assembly, operat-

ing, inspection, maintenance and cleaning

procedures. Write the product’s serial

number in the back of the manual near the

assembly diagram (or month and year of

purchase if product has no number). Keep

this manual and the receipt in a safe and

dry place for future reference.

IMPORTANT SAFETY

INSTRUCTIONS

In this manual, on the labeling,

and all other information provid-

ed with this product:

This is the safety alert

symbol. It is used to alert

you to potential personal

injury hazards. Obey all

safety messages that

follow this symbol to avoid

possible injury or death.

DANGER indicates

a hazardous

situation which, if not

avoided, will result in death or

serious injury.

WARNING

indicates a

hazardous situation which, if

not avoided, could result in

death or serious injury.

CAUTION, used

with the safety

alert symbol, indicates a

hazardous situation which, if

not avoided, could result in

minor or moderate injury.

NOTICE is used to

address practices

not related to personal injury.

CAUTION, without

the safety alert

symbol, is used to address

practices not related to

personal injury.

READ AND UNDERSTAND ALL

INSTRUCTIONS

When using this Electric Paint

Shaker, safety precautions

should always be followed in-

cluding the following:

Work Area Safety

Do not use outdoors.1.

Do not let cord hang over edge of2.

table or counter, or touch hot sur-

faces.

Keep the work area well lit. Make3.

sure there is adequate surrounding

workspace. Keep the work area free

of obstructions and debris.

Electrical Safety

1. To protect against electri-

cal shock do not immerse

cord, plugs, or the main

unit in water or other

liquid. Only the non-elec-

trical parts of the unit may be im-

mersed for cleaning. Thoroughly

clean and dry these parts prior to rst

use and before every subsequent

use.

Unplug from outlet when not in use2.

and before maintenance or cleaning.

SKU 66301 For technical questions, please call 1-800-444-3353. Page 3

Do not operate this Electric Paint3.

Shaker with a damaged cord or plug

or after it malfunctions or has been

damaged in any manner.

Do not use this product in a damp or4.

wet location.

Do not clean with metal scouring5.

pads. Metal pieces can break off the

pads and touch electrical parts involv-

ing risk of shock.

Power Cord Safety

1. This Electric Paint Shaker comes

with a grounded, 3-Prong power

cord. A short power supply cord is

provided to reduce risks resulting

from becoming entangled in or trip-

ping over a longer cord.

2. Longer extension cords are available

and may be used if care is exercised

in their use.

3. If a long extension cord is used,

the marked electrical rating of thea.

(detachable power supply cord or)

extension cord should be at least as

great as the electrical rating of the

tool.

if the tool is of the grounded type,b.

the extension cord should be a

grounding type 3-wire cord, and

the longer cord should be arrangedc.

so that it will not drape over the

counter top or workbench where

it can be pulled on by children or

tripped over.

General and Specic Safety

Precautions

WARNING! To prevent serious per-1.

sonal injury:

Always wear ANSI-approved safetya.

goggles when operating this Electric

Paint Shaker.

Check for loose or broken parts be-b.

fore using and DO NOT use if any-

thing abnormal is found. Have the

Electric Paint Shaker repaired before

using.

Verify that all containers are securelyc.

closed before placing them on this

Paint Shaker.

Securely fasten Hold Down Bar (4)d.

to lid of container, and thread the

Safety Lock Nut (44) against the

Hold Down Bar before turning on

timer.

DO NOT allow children to use and/ore.

play with this Electric Paint Shaker.

DO NOT use this Electric Paint Shak-2.

er while under the inuence of alco-

hol or drugs. Read warning labels if

taking prescription medicine to deter-

mine if your judgment or reexes are

impaired while doing so. If there is

any doubt, DO NOT operate this tool.

DO NOT use this Electric Paint Shak-3.

er for other than it’s intended use.

Maintain labels and nameplates on4.

the appliance. These carry important

safety information. If unreadable or

missing, contact Harbor Freight Tools

for a replacement.

WARNING: Handling the cord on5.

this product will expose you to lead,

a chemical known to the State of

California to cause cancer, and birth

defects or other reproductive harm.

Wash hands after handling. (Califor-

nia Health & Safety Code § 25249.5,

et seq.)

SKU 66301 For technical questions, please call 1-800-444-3353. Page 4

The warnings, precautions, and in-6.

structions discussed in this instruction

manual cannot cover all possible con-

ditions and situations that may occur.

It must be understood by the operator

that common sense and caution are

factors which cannot be built into this

product, but must be supplied by the

operator.

SAVE THESE

INSTRUCTIONS.

SPECIFICATIONS

Motor

120V / 60 Hz / 2.3 AMPS.

1170 Oscillations Per

Minute

Paint Shaker Timer 0 to 15 Minutes with

Automatic Shut-Off

Container Sizes Gal, Qt, Pt. and 12 oz.

Spray Can.

UNPACKING

When unpacking, check to make sure

that the item is intact and undamaged. If

any parts are missing or broken, please

call Harbor Freight Tools at the number

shown on the cover of this manual as soon

as possible.

CLEANING

Read the ENTIRE IMPORTANT

SAFEGUARDS section at

the beginning of this manual

including all text under

subheadings therein before set

up or use of this product.

TO PREVENT

SERIOUS INJURY

FROM ACCIDENTAL

OPERATION OR ELECTRIC

SHOCK:

Before cleaning this tool,

make sure the Timer Switch is

turned off, the cord is

unplugged, and the unit has

cooled completely.

Do not immerse motor/heating

element, cord, or plug in water

or any other liquid.

Wipe with slightly dampened, soft, clean

cloth. Allow unit to dry completely before

assembly or use.

ASSEMBLY

This Electric Paint Shaker comes fully as-

sembled.

Read the ENTIRE IMPORTANT

SAFEGUARDS section at

the beginning of this manual

including all text under

subheadings therein before set

up or use of this product.

TO PREVENT

SERIOUS INJURY

FROM ACCIDENTAL

OPERATION OR ELECTRIC

SHOCK:

Before adjustment, make sure

the Timer Switch is turned off,

the cord is unplugged, and

the unit has cooled

completely.

SKU 66301 For technical questions, please call 1-800-444-3353. Page 5

NOTE: This is a fully portable Electric

Paint Shaker and does not have

to be permanently mounted to a

counter or workbench.

OPERATION

Read the ENTIRE IMPORTANT

SAFEGUARDS section at

the beginning of this manual

including all text under

subheadings therein before set

up or use of this product.

Before using, check for cracked,1.

loose, or broken parts. Do not use

if anything abnormal is found. Have

the Electric Paint Shaker repaired by

a qualied technician before using.

Adjustment

Knob Assem-

bly (45)

Safety Lock

Nut (44)

Release Pin

Top Bar (3)

Hold Down

Bar (4)

Platform (7)

Timer

(Switch) (32)

Figure 1

2. Place the Electric Paint Shaker on a

at surface secure enough to sup-

port both the Electric Paint Shaker

and the paint container being shaken.

Note: On the bottom of the Paint

Shaker are two Feet (25) which can

be adjusted

so that this

product sits

evenly on

the surface.

Simply

thread the

nut on the

Adjustable Feet to change the height

of each adjustable foot.

Back off the Safety Lock Nut (44)3.

away from the Hold Down Bar (4).

Raise the Hold Down Bar by turning

the Adjustment Knob Assembly (45)

counterclockwise. See Figure 1.

With one hand, raise the Hold Down4.

Bar while setting the paint container

(gallon, quart, pint or spray can) onto

the center of the Platform (7). If you

are shaking a gallon container with

an attached bail, place the “bail”

towards one of the Slide Tubes to

prevent apping and excess noise.

NOTE: If a spray can is being shaken,

remove the top cap and the spray

nozzle before placing it on the Plat-

form.

With paint container centered on the5.

Platform (note the grooved circles on

the Platform (7); used to position dif-

ferent sized containers), let the Hold

Down Bar

settle onto

the top of the

container.

Tighten the

two Locking

Knobs and

the Adjust-

SKU 66301 For technical questions, please call 1-800-444-3353. Page 6

ment Knob Assembly (turning clock-

wise). Tighten the Safety Lock Nut

(clockwise) nger tight, then snug

it with one turn using an adjustable

wrench (not supplied).

WARNING! The Hold Down Bar must

rest rmly and evenly against the

top of the paint container. Once

the shaking (agitation) begins, the

container, if it is not held secure,

may y off the Paint Shaker caus-

ing the paint to spill out, and/or

causing serious personal injury.

Turn the Knob (31) on the Timer (32)6.

clockwise to three minutes (usually

good for most uses), or any position

up to fteen minutes (maximum used

for paint that has been allowed to set-

tle for long periods). The Timer will

run down to “zero” and shut off auto-

matically. NOTE: If a shorter period

is needed of if you need to stop the

Electric Paint Shaker for any reason,

simply manually rotate the Knob (31)

counter clockwise to its OFF position.

Always wait till the Electric Paint7.

Shaker stops completely before re-

moving the paint container.

To remove the paint container, back8.

off the Safety Lock Nut (44) and

turn the Adjustment Knob Assembly

counterclockwise till tension on the

Hold Down Bar is released allowing it

to slide up the Slide Tubes. Slide the

paint container out sideways.

When nished using the Electric Paint 9.

Shaker, disconnect its power supply,

wipe down all exterior surfaces with a

soft, clean cloth, then store the appli-

ance indoors out of children’s reach.

INSPECTION AND

MAINTENANCE

TO PREVENT

SERIOUS INJURY

FROM ACCIDENTAL

OPERATION OR ELECTRIC

SHOCK:

Before inspection or

maintenance, make sure the

Timer switch is turned off, the

cord is unplugged, and the

unit has cooled completely.

TO PREVENT SERIOUS

INJURY FROM TOOL

FAILURE:

Do not use if damaged. If

abnormal noise or vibration

occurs, have the problem

corrected before further use.

BEFORE EACH USE, inspect the gen-

eral condition. Check for loose screws,

misalignment or binding of moving parts,

cracked or broken parts, damaged electri-

cal wiring, and any other condition that

may affect its safe operation.

SKU 66301 For technical questions, please call 1-800-444-3353. Page 7

PARTS LIST

Part Description Q’ty

1 Locking Knob 2

2 Flat Washer 4

3 Top Bar 1

4 Hold Down Bar 1

5 Support Tube 2

6 Screw M6 X 20 4

7 Platform 1

8 Upper Spring Assembly (4 Springs) 1

9 Cover 1

10 Nut M6 3

11 Screw M6 X 16 1

12 Mid Plate 1

13 Lower Spring Assembly (4 Springs) 1

14 Motor 1

15 Connect Plate 1

16 Flat Washer φ6 6

17 Screw M6 X 25 8

18 Base 1

19 Bracket 4

20 Spring Washer φ8 4

21 Flat Washer φ8 4

22 Bolt M8 X 16 4

23 Cap Nut 4

PARTS LIST

Part Description Q’ty

24 Stud 2

25 Adjustable Foot 2

26 Rubber Foot 2

27 Small Flat Washer φ6 2

28 Flat Washer φ4 1

29 Screw M4 X 12 1

30 Screw M3 X 6 2

31 Knob 1

32 Timer (Switch) 1

33 Cord Stopper 1

34 Cord 1

35 Flat Washer φ5 6

36 Spring Washer φ5 6

37 Nut M5 6

38 Flyweight 1

39 Bolt M10 X 20 2

40 Spring Washer φ10 2

41 Pin Lock 1

42 Spring 1

43 Retaining Ring 1

44 Safety Lock Nut M12 1

45 Adjustment Knob Assembly 1

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY

DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR

DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT

HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS

QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/

OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD

BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE

BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE

ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER

INSTALLATION OF REPLACEMENT PARTS THERETO.

Record Product’s Serial Number Here:

Note: If product has no serial number, record month and year of purchase instead.

Note: Some parts are listed and shown for illustration purposes only, and are not avail-

able individually as replacement parts.

SKU 66301 For technical questions, please call 1-800-444-3353. Page 8

ASSEMBLY DIAGRAM

Indice

Altri manuali Chicago Electric Utensili elettrici

Chicago Electric

Chicago Electric 68303 Manuale utente

Chicago Electric

Chicago Electric 61778 Istruzioni per il montaggio

Chicago Electric

Chicago Electric 35778 Manuale utente

Chicago Electric

Chicago Electric 62302 Istruzioni per il montaggio

Chicago Electric

Chicago Electric 46935 Manuale di installazione

Chicago Electric

Chicago Electric 95313 Manuale di installazione

Chicago Electric

Chicago Electric 37793 Manuale utente

Chicago Electric

Chicago Electric 47937 Manuale utente

Chicago Electric

Chicago Electric 43585 Manuale utente

Chicago Electric

Chicago Electric 62213 Istruzioni per il montaggio

Chicago Electric

Chicago Electric 66508 Manuale utente

Chicago Electric

Chicago Electric 67631 Manuale di installazione

Chicago Electric

Chicago Electric 35 LB Manuale di istruzioni originale

Chicago Electric

Chicago Electric 67845 Manuale di installazione

Chicago Electric

Chicago Electric 68364 Manuale utente

Chicago Electric

Chicago Electric 92772 Manuale di installazione

Chicago Electric

Chicago Electric 90672 Manuale utente

Chicago Electric

Chicago Electric 69343 Istruzioni per il montaggio

Chicago Electric

Chicago Electric 90287 Manuale utente

Chicago Electric

Chicago Electric 96289 Manuale di installazione

Chicago Electric

Chicago Electric 69946 Manuale utente

Chicago Electric

Chicago Electric 42831 Manuale utente

Chicago Electric

Chicago Electric 92798 Manuale utente

Chicago Electric

Chicago Electric 67632 Manuale di installazione

Manuali Utensili elettrici popolari di altre marche

AEG

AEG OMNI-JS Manuale utente

SIP

SIP 01533 Manuale utente

Ribimex

Ribimex PRS499 Manuale utente

3M Fiber Optic Connector Crimp Tool Manuale utente

Ryobi

Ryobi P524 Manuale utente

ROJEK

ROJEK FSN 300A Manuale utente

Kemper

Kemper 1740PRO Manuale utente

WABCO

WABCO OptiTire Manuale utente

EINHELL

EINHELL TE-MS 18/210 Li Manuale utente

Orgapack

Orgapack OR-T 85 Guida rapida

TOUGHCUT

TOUGHCUT Diamond 400 Manuale utente

Yaros

Yaros PB-3603 Manuale utente

Fein

Fein BSS 2.0 E Guida all'installazione

Baileigh Industrial

Baileigh Industrial SS-2725 Manuale utente

Milwaukee

Milwaukee 2674-20 Manuale utente

Fein

Fein BLs 1.6 Manuale utente

Princess

Princess Electric Multi Sharpener Manuale utente

FOREDOM

FOREDOM K.1050 Manuale