Chicago Electric 96298 Manuale utente

10.8 VOLT CORDLESS DRIVER

Model

96298

OPERATING INSTRUCTIONS

Due to continuing improvements, actual product may differ slightly from the product described herein.

3491 Mission Oaks Blvd., Camarillo, CA 93011

Visit our Web site at: http://www.harborfreight.com

TO PREVENT SERIOUS INJURY, READ

AND UNDERSTAND ALL WARNINGS AND

INSTRUCTIONS BEFORE USE.

this manual or any artwork contained herein may be reproduced in any shape

or form without the express written consent of Harbor Freight Tools.

For technical questions or replacement parts, please call 1-800-444-3353.

SKU 96298 For technical questions, please call 1-800-444-3353. PAGE 2

PRODUCT SPECIFICATIONS

Power Source 1.3Ah Battery

Charge Time 5-7 Hours, after initial charge

Charger Input 120V ~60Hz

Chuck Type 1/4” Hex Shank Drive

Torque Settings 24

Variable Speed 0-500 RPM

Maximum Torque 80 in./lb.

Reversible Yes

Trigger Lock Yes

Weight 1.8 Pounds

Included

1 Hex shank adapter

6 Phillips head bits

3 ﬂat head bits

1 Battery Charger

Save This Manual

You will need this manual for the safety warnings and precautions, assembly, oper-

ating, inspection, maintenance and cleaning procedures, parts list and assembly diagram.

Keep your invoice with this manual. Write the invoice number on the inside of the front

cover. Keep this manual and invoice in a safe and dry place for future reference.

GENERAL SAFETY RULES

WARNING!

READ AND UNDERSTAND ALL INSTRUCTIONS

Failure to follow all instructions listed below may result

in electric shock, ﬁre, and/or serious injury.

SAVE THESE INSTRUCTIONS

Work Area

Keep your work area clean and well lit. Cluttered benches and dark areas

invite accidents.

Do not operate power tools in explosive atmospheres, such as in the pres-

ence of ﬂammable liquids, gases, or dust. Power tools create sparks which may

ignite the dust or fumes.

Keep bystanders and children away while operating a power tool. Distractions

can cause you to lose control. Protect others in the work area from debris such as

chips and sparks. Provide barriers or shields as needed.

SKU 96298 For technical questions, please call 1-800-444-3353. PAGE 3

Electrical Safety

Avoid body contact with grounded surfaces such as pipes, radiators, ranges,

and refrigerators. There is an increased risk of electric shock if your body is

grounded.

Do not expose power tools to rain or wet conditions. Water entering a power

tool will increase the risk of electric shock.

Do not abuse the Charger’s power cord. Never use the Power Cord to carry

the Charger or pull the Plug from an outlet. Keep the Power Cord away from

heat, oil, sharp edges, or moving parts. Replace damaged Power Cords im-

mediately. Damaged Power Cords increase the risk of electric shock.

Personal Safety

Stay alert. Watch what you are doing, and use common sense when operat-

ing a power tool. Do not use a power tool while tired or under the inﬂuence

of drugs, alcohol, or medication. A moment of inattention while operating power

tools may result in serious personal injury.

Dress properly. Do not wear loose clothing or jewelry. Contain long hair.

Keep your hair, clothing, and gloves away from moving parts. Loose clothes,

jewelry, or long hair can be caught in moving parts.

Avoid accidental starting. Be sure the Rotation Button (6) is in the locked

position before inserting the Battery. Carrying power tools with your ﬁnger on

the trigger, or inserting the Battery with the trigger depressed, invites accidents.

Do not overreach. Keep proper footing and balance at all times. Proper footing

and balance enables better control of the power tool in unexpected situations.

Use safety equipment. Always wear eye protection. Dust mask, nonskid safety

shoes, hard hat, or hearing protection must be used for appropriate conditions.

Always wear ANSI-approved safety goggles when working with this tool.

Tool Use and Care

Use clamps (not included) or other practical ways to secure and support the

workpiece to a stable platform. Holding the work by hand or against your body

is unstable and may lead to loss of control.

Do not force the tool. Use the correct tool for your application. The correct

tool will do the job better and safer at the rate for which it is designed.

Do not use the power tool if the trigger does not operate it. Any tool that cannot

be controlled with the trigger is dangerous and must be replaced.

SKU 96298 For technical questions, please call 1-800-444-3353. PAGE 4

Remove the battery from the tool and set the Rotation Button (6) to the cen-

ter, locked position, before making any adjustments, changing accessories,

or storing the tool. These preventive safety measures reduce the risk of starting

the tool accidentally.

Store idle tools out of reach of children and other untrained persons. Tools

are dangerous in the hands of untrained users.

Maintain the Cordless Driver with care. Keep screwdriver bits clean. Properly

maintained accessories with a clean edge are less likely to bind and are easier to

control. Do not use a damaged tool or accessory. Tag damaged tools “Do not use”

until repaired.

Check for misalignment or binding of moving parts, breakage of parts, and any

other condition that may affect the tool’s operation. If damaged, have the tool

serviced before using. Many accidents are caused by poorly maintained tools.

Use only accessories that are recommended by the manufacturer for your

model. Accessories that may be suitable for one tool may become hazardous

when used on another tool.

Service

Tool service must be performed only by qualiﬁed repair personnel. Service or

maintenance performed by unqualiﬁed personnel could result in a risk of injury.

When servicing a tool, use only identical replacement parts. Follow instruc-

tions in this manual. Use of unauthorized parts or failure to follow maintenance

instructions may create a risk of electric shock or injury.

SPECIFIC SAFETY RULES

Maintain a safe working environment. Keep the work area well lit. Make sure

there is adequate surrounding workspace. Always keep the work area free of ob-

structions, grease, oil, trash, and other debris. Do not use the Cordless Driver in

areas near ﬂammable chemicals, dusts, and vapors. Do not use this product in a

damp or wet location.

Maintain labels and nameplates on the Cordless Driver. These carry important

information. If unreadable or missing, contact Harbor Freight Tools for a replace-

ment.

When using the Cordless Driver, always maintain a ﬁrm grip on the tool with

both hands.

Hold the tool by its insulated gripping surfaces when performing an opera-

tion where the Cordless Driver may contact hidden wiring. Contact with a

SKU 96298 For technical questions, please call 1-800-444-3353. PAGE 5

“live” wire will make exposed metal parts of the Cordless Driver “live” and shock

the operator.

Do not use the Cordless Driver or Charger if it has been dropped, damaged,

left outdoors, or immersed in liquid.

To avoid electric shock, do not pull or carry the Charger by its Power Cord or

pull the Power Cord around sharp corners or edges. Do not unplug the Charger

by pulling on the Power Cord. Keep the Power Cord away from heated surfaces.

To avoid electrical shock, do not handle the Charger, the Adapter, or the Cord-

less Driver with wet hands.

Keep the Handles of the Cordless Driver dry, clean, and free from oil or

grease.

Avoid unintentional starting. Make sure you are prepared to begin work before

turning on the Cordless Driver.

Never leave the Charger unattended when it is plugged into an electrical outlet.

Unplug the Charger from its electrical outlet before leaving. Place the Charger on

a solid surface such as a garage ﬂoor; never place on anything ﬂammable.

PROPER BATTERY PACK CARE: Battery Pack (19) leakage may occur under

extreme usage or temperature conditions. If Battery Pack ﬂuid comes in con-

tact with skin, rinse with lemon juice and vinegar then wash with soap and water.

If the ﬂuid comes into contact with the eyes, ﬂush with water for several minutes

and contact a doctor immediately. Never burn the Battery Pack, as it can explode

in a ﬁre. Do not charge the Cordless Driver with a leaking Battery Pack. Contact

local solid waste authorities for instructions on correct disposal or recycling of the

Battery Pack.

WARNING! Some dust created by power sanding, sawing, grinding, drilling, and

other construction activities, contain chemicals known (to the State of California) to

cause cancer, birth defects or other reproductive harm. Some examples of these

chemicals are: lead from lead-based paints, crystalline silica from bricks and cement

or other masonry products, arsenic and chromium from chemically treated lumber.

Your risk from these exposures varies, depending on how often you do this type of

work. To reduce your exposure to these chemicals: work in a well ventilated area,

and work with approved safety equipment, such as dust masks that are specially

designed to ﬁlter out microscopic particles. (California Health & Safety Code §

25249.5, et seq.)

WARNING! People with pacemakers should consult their physician(s) before

using this product. Operation of electrical equipment in close proximity to a heart

pacemaker could cause interference or failure of the pacemaker.

10.

11.

12.

13.

SKU 96298 For technical questions, please call 1-800-444-3353. PAGE 6

GROUNDING

WARNING!

Improperly connecting the grounding wire can result in the risk of electric shock.

Check with a qualiﬁed electrician if you are in doubt as to whether the outlet is

properly grounded. Do not modify the power cord plug provided with the tool.

Never remove the grounding prong from the plug. Do not use the tool if the

power cord or plug is damaged. If damaged, have it repaired by a service facil-

ity before use. If the plug will not ﬁt the outlet, have a proper outlet installed by

a qualiﬁed electrician.

GROUNDED TOOLS: TOOLS WITH THREE PRONG PLUGS

Tools marked with “Grounding Required” have a three wire cord and three prong

grounding plug. The plug must be connected to a properly grounded outlet. If

the tool should electrically malfunction or break down, grounding provides a low

resistance path to carry electricity away from the user, reducing the risk of electric

shock. (See Figure A.)

The grounding prong in the plug is connected through the green wire inside the

cord to the grounding system in the tool. The green wire in the cord must be the

only wire connected to the tool’s grounding system and must never be attached to

an electrically “live” terminal. (See Figure A.)

Your tool must be plugged into an appropriate outlet, properly installed and grounded

in accordance with all codes and ordinances. The plug and outlet should look like

those in the following illustration. (Se Figure A.)

FIGURE A FIGURE B.

DOUBLE INSULATED TOOLS: TOOLS WITH TWO PRONG PLUGS

Tools marked “Double Insulated” do not require grounding. They have a special

double insulation system which satisﬁes OSHA requirements and complies with

the applicable standards of Underwriters Laboratories, Inc., the Canadian Standard

Association, and the National Electrical Code. (See Figure B.)

SKU 96298 For technical questions, please call 1-800-444-3353. PAGE 7

Double insulated tools may be used in either of the 120 volt outlets shown in the

preceding illustration. (See Figure B.)

EXTENSION CORDS

Grounded tools require a three wire extension cord. Double Insulated tools can

use either a two or three wire extension cord.

As the distance from the supply outlet increases, you must use a heavier gauge

extension cord. Using extension cords with inadequately sized wire causes a seri-

ous drop in voltage, resulting in loss of power and possible tool damage.

(See Chart A, next page.)

The smaller the gauge number of the wire, the greater the capacity of the cord. For

example, a 14 gauge cord can carry a higher current than a 16 gauge cord.

(See Chart A.)

When using more than one extension cord to make up the total length, make sure

each cord contains at least the minimum wire size required. (See Chart A.)

If you are using one extension cord for more than one tool, add the nameplate am-

peres and use the sum to determine the required minimum cord size.

(See Chart A.)

If you are using an extension cord outdoors, make sure it is marked with the sufﬁx

“W-A” (“W” in Canada) to indicate it is acceptable for outdoor use.

Make sure your extension cord is properly wired and in good electrical condition.

Always replace a damaged extension cord or have it repaired by a qualiﬁed electri-

cian before using it.

Protect your extension cords from sharp objects, excessive heat, and damp or wet

areas.

SKU 96298 For technical questions, please call 1-800-444-3353. PAGE 8

RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS*

(120 OR 240 VOLT)

NAMEPLATE

AMPERES

(at full load)

EXTENSION CORD LENGTH

25 Feet 50 Feet 75 Feet 100 Feet 150 Feet

0 – 2.0 18 18 18 18 16

2.1 – 3.4 18 18 18 16 14

3.5 – 5.0 18 18 16 14 12

5.1 – 7.0 18 16 14 12 12

7.1 – 12.0 18 14 12 10 -

12.1 – 16.0 14 12 10 - -

16.1 – 20.0 12 10 - - -

Chart A * Based on limiting the line voltage drop to ﬁve volts at 150% of the rated amperes.

SYMBOLOGY

Double Insulated

Canadian Standards Association

Underwriters Laboratories, Inc.

V~ Volts Alternating Current

AAmperes

n0xxxx/min. No Load Revolutions per Minute (RPM)

SKU 96298 For technical questions, please call 1-800-444-3353. PAGE 9

UNPACKING

When unpacking, check to make sure that the product is complete and undamaged.

If any parts are missing or broken, please call Harbor Freight Tools at the number shown

on the cover of this manual as soon as possible.

CHARGING (INITIAL CHARGE)

The Battery Pack (19) requires charging before use. The recommended initial charge

time is twelve hours, prior to ﬁrst use of the Cordless Driver.

Note: Always switch to a fresh battery when tool performance begins to diminish. Severe

heat is destructive to batteries; the more heat generated, the faster the battery will

lose power. A battery that gets too hot can be permanently damaged. Never over-

discharge a battery by using the tool after performance decreases. Never attempt to

discharge a battery by continuing to pull the trigger. When tool performance begins

to diminish, stop the tool, recharge the battery, and use a fully charged battery for

optimal performance.

When the Battery Pack-after the initial charge-requires recharging it must charge

for ﬁve to seven hours in order to operate at full power.

Charging room temperature: 50° F. – 104° F.

Depress both buttons at the rear of the Battery Pack and slide the unit down to

detach from the Driver.

Insert the Battery Pack (19) into the Charger (24) (the Battery Pack can only ﬁt into

the Charger in one position), plug Charger

into Adapter (25), and plug Adapter into any

standard electrical outlet.

While charging, the Battery Pack, Charger,

and Adapter may become warm to the touch.

This is normal, and does not indicate a prob-

lem.

When the Battery Pack is in the Charger,

both the red and green lights on the Charger

will be illuminated while charging, when the

Battery Pack is fully charged the red light

will turn off, indicating that the Battery Pack

is ready for use. Once the Battery Pack is

fully charged, unplug the Charger from the

electrical outlet, unplug the Charger from the electrical outlet and remove the Bat-

tery Pack from the Adapter.

Battery

Pack (19)

Charger

(24)

Adapter

(25)

Battery

Pack (19)

Charger

(24)

Adapter

(25)

SKU 96298 For technical questions, please call 1-800-444-3353. PAGE 10

OPERATING INSTRUCTIONS

NOTE: For additional information regarding the parts listed in the following pages, refer to

the Parts List & Assembly Diagram.

WARNING! Remove the Battery Pack (19) from the tool and set the Rotation Button

(6) to its center, locked, position before making any adjustments, changing acces-

sories, or storing the tool.

Battery Pack

(19)

Trigger (12)

Gear Box with

Torque Ring (2)

Rotation Button (6)

Chuck (1)

To install a screwdriver bit, insert the correct Bit (26) for the application into the

magnetic Bit Adapter (27). Never insert one of the included Bits (26) directly

into the Chuck. A smaller gauge than 1/4” will not be ﬁrmly secured and may

result in injury or property damage. With the Chuck (1) pointing away from you,

pull gently on the Chuck sleeve and insert the Bit Adapter into the Chuck. Release

the Chuck sleeve and the Bit Adapter will lock ﬁrmly in place. The Chuck accepts

1/4” Hex Shank only. To remove the Bit Adapter (27), reverse the above-mentioned

procedure.

Secure the workpiece in place, using a vise or clamps (not included).

Note: Never change Torque Setting while the Cordless Driver is still rotating, as this can

damage the Cordless Driver.

Selecting an appropriate torque setting (1-24):

Indice

Altri manuali Chicago Electric Utensili elettrici

Chicago Electric

Chicago Electric 68221 Manuale utente

Chicago Electric

Chicago Electric 62213 Istruzioni per il montaggio

Chicago Electric

Chicago Electric 95313 Manuale di installazione

Chicago Electric

Chicago Electric 92115 Manuale utente

Chicago Electric

Chicago Electric Chicago 94560 Manuale di installazione

Chicago Electric

Chicago Electric 35 LB Manuale di istruzioni originale

Chicago Electric

Chicago Electric 46055 Manuale utente

Chicago Electric

Chicago Electric 62866 Istruzioni per il montaggio

Chicago Electric

Chicago Electric 60713 Manuale di istruzioni originale

Chicago Electric

Chicago Electric 68861 Manuale utente

Chicago Electric

Chicago Electric 33710 Guida di riferimento rapido

Chicago Electric

Chicago Electric 37793 Manuale di installazione

Chicago Electric

Chicago Electric 68364 Manuale utente

Chicago Electric

Chicago Electric 90287 Manuale utente

Chicago Electric

Chicago Electric 68199 Manuale utente

Chicago Electric

Chicago Electric 68821 Manuale utente

Chicago Electric

Chicago Electric 38437 Manuale utente

Chicago Electric

Chicago Electric 68012 Manuale utente

Chicago Electric

Chicago Electric 67119 Manuale di istruzioni

Chicago Electric

Chicago Electric 68012 Istruzioni per il montaggio

Chicago Electric

Chicago Electric 61687 Manuale dell'operatore

Chicago Electric

Chicago Electric 90541 Manuale utente

Chicago Electric

Chicago Electric 97114 Manuale di installazione

Chicago Electric

Chicago Electric 68848 Manuale utente

Manuali Utensili elettrici popolari di altre marche

AEG

AEG OMNI-JS Manuale utente

SIP

SIP 01533 Manuale utente

Ribimex

Ribimex PRS499 Manuale utente

3M Fiber Optic Connector Crimp Tool Manuale utente

Ryobi

Ryobi P524 Manuale utente

ROJEK

ROJEK FSN 300A Manuale utente

Kemper

Kemper 1740PRO Manuale utente

WABCO

WABCO OptiTire Manuale utente

EINHELL

EINHELL TE-MS 18/210 Li Manuale utente

Orgapack

Orgapack OR-T 85 Guida rapida

TOUGHCUT

TOUGHCUT Diamond 400 Manuale utente

Yaros

Yaros PB-3603 Manuale utente

Fein

Fein BSS 2.0 E Guida all'installazione

Baileigh Industrial

Baileigh Industrial SS-2725 Manuale utente

Milwaukee

Milwaukee 2674-20 Manuale utente

Fein

Fein BLs 1.6 Manuale utente

Princess

Princess Electric Multi Sharpener Manuale utente

FOREDOM

FOREDOM K.1050 Manuale