CHIEF MSB-6053 Manuale utente
INSTALLATION INSTRUCTIONS
CHIEF MANUFACTURING, a products division of
Milestone AV Technologies.
1-800-582-6480 952-894-6280 FAX 952-894-6918
8401 EAGLE CREEK PKWY
SAVAGE, MINNESOTA 55378 USA
8840-000040 RevC
2008 Milestone AV Technologies
A Duchossois Group Company
www.chiefmfg.com
12/08
ALL COMPONENTS MUST BE SECURELY FASTENED TO A
STRUCTURAL MEMBER CAPABLE OF SUPPORTING 4 TIMES
THE COMBINED WEIGHT OF ALL COMPONENTS PLUS THE
EQUIPMENT BEING MOUNTED. IF IT CANNOT SUPPORT
THIS WEIGHT, THE STRUCTURE MUST BE REINFORCED.
THE MAXIMUM WEIGHT TO BE INSTALLED ON THE
INTERFACE IS 125 POUNDS (79.38 KG).
MSB-6053
DISPLAY MOUNTING BRACKET
Prior to assembly, unpack carton completely and verify contents.
(2) Interface Side Brackets (2) Interface Center Brackets
(4) Mounting Buttons – Tapped (8) 10-24 x .5 Button Head Cap Screws
(4) M8 x 65mm Hex Head Cap Screws (4) 18mm x 8.3mm x 20mm Nylon Spacers
(4) M8 Flat Washers (4) Nylon Shoulder Washers
(1) 1/8” Allen Key (4) .74x.39x1.0” Nylon Spacers
BEFORE PROCEEDING, READ INSTALLATION INSTRUCTIONS COMPLETELY
DISPLAYS ARE EXTREMELY FRAGILE.
NOTE:If installing screen on a Chief J-series wall mount, proceed to Step 3 (J-Series VESA Interface Installation).
1. Chief Q-latch Button Installation (Used with MSR, MTR, MWH, MWR, MCS and MCD mounts):
Using a 10-24 button head cap screw inserted from back side of bracket, secure mounting button, with
chamfered hole of mounting button (larger surface) facing bracket, to center brackets (four places) (see
Figure 2 & Figure3).
2. Proceed to Step 4 (Side Bracket Assembly).
CAUTION!
Figure 1
WARNING!
Figure 2 Figure 3
3. J-Series VESA Interface Installation:
Using the 10-24 button head cap screws along with the 10-24 Nylock
nuts (provided with J-Series mount), attach VESA interface from J-Series mount to center brackets (see
Figure 4 & Figure 5).
4. Side Bracket Assembly: Attach center brackets to side brackets using the 10-24 button head cap screws (see
Figure 6 & Figure 7).
5. Bracket Installation: Place four nylon spacers over mounting holes on back of screen. Attach mounting
brackets to display using the M8 screws, shoulder and steel washers (see Figure 8 & Figure 9). Do not over
tighten screws.
NOTE: Select nylon spacers to use based upon the type of device being mounted. The remaining four
spacers will not be used.
6. Follow the Chief mount instruction manual for screen installation.
Figure 4 Figure 5
Figure 6 Figure 7
Figure 8 Figure 9
Indice
Altri manuali CHIEF Supporto TV
CHIEF
CHIEF FSB-4228 Manuale utente
CHIEF
CHIEF iC Series Manuale utente
CHIEF
CHIEF CM2 Manuale utente
CHIEF
CHIEF PSB-2397 Manuale utente
CHIEF
CHIEF MPAU Manuale utente
CHIEF
CHIEF FHB7017 Manuale utente
CHIEF
CHIEF KSA1250 Manuale utente
CHIEF
CHIEF PSM-2534 Manuale utente
CHIEF
CHIEF FSB-4226 Manuale utente
CHIEF
CHIEF PSBU Manuale utente
CHIEF
CHIEF CM8 Manuale utente
CHIEF
CHIEF TA350 Manuale utente
CHIEF
CHIEF CHILCM1X2U Manuale utente
CHIEF
CHIEF Kontour K4G310 Manuale utente
CHIEF
CHIEF MSBU Manuale utente
CHIEF
CHIEF SSC Bracket SSC-1 Manuale utente
CHIEF
CHIEF PSB-2307 Manuale utente
CHIEF
CHIEF iCMPFM1S Manuale utente
CHIEF
CHIEF PSB-2364 Manuale utente
CHIEF
CHIEF Flat Panel Wall Plate Accessory FSA-1001 Manuale utente
