ChiliTec MILOS 22781 Manuale utente
operation manual EAR (WEEE): DE25841852
LUCID VerpackG: DE5562476395648
GRS (UBA Register) No.: 21003466
- Product data sheet-Page 1 of 2 Status: 01/2020 - Ver. 1.01
Item no.: 22781 (white) - 23045 (anthracite)
MILOS dimmer for LED lamps
250V~/ 3-60W, incl. frame, UP
Product description:
Brightness control through phase control for dimmable LED lamps, incl. pressure switch
function! The MILOS series offers you mature quality and an excellent look and feel with a matt
white finish at attractive prices.
Technical details:
• All components suitable for
lengthwise and crosswise assembly
• LED 3-60W (max. 10 LED lamps)
• Halogen lamps 7-110W
• Switch ON/OFF via control button
• for electronic transformers
• 2-wire technology - simple assembly
• Screw connection
Safety instructions and important information!
In order to ensure safety at all times and to use the full performance range of the device, please
read the safety instructions carefully and at your leisure!
The product must not be changed technically or mechanically, otherwise the operating license
and the conformity will expire immediately!! The type plate / imprint must not be removed under
any circumstances! Check the product for damage before each use. If damage is visible on the
product, it must be checked, repaired or replaced by a specialist company and disposed of in
accordance with the applicable guidelines (see footer on page 1). Under no circumstances may a
damaged or defective product continue to be put into operation! Please make sure that all
packaging material and accessories, especially small parts such as screws and foils, are protected
from children and animals. Danger of suffocation! In the event of non-compliance with the
instructions or improper use, the manufacturer Misappropriation or changes made to the
product, no liability for property damage or personal injury. The product must never be covered
during operation! This product must never be operated, kept, placed or stored within the reach
of children or animals.
Please keep this manual safe. If this product is passed on, the instructions and the packaging
must be included. Thanks! We reserve the right to misprints or changes to the packaging, the
product or the instructions.
- Notes on cleaning, care and environmental protection -
Clean this product with a dry, lint-free cotton cloth. For heavier soiling, possibly with a slightly
damp, slightly damp cloth. Make sure that the product is switched off and disconnected from the
mains. Never use chemical cleaning agents. Never use liquids that could damage the surface of
the product (e.g. scouring cream). The product contains no serviceable parts. The product is
marked with a crossed-out garbage can. Please note the disposal information in the footer on the
first page of these instructions.
Electronic devices that are marked with the crossed-out wheeled bin do not belong in the household waste! You can hand in these
devices free of charge to municipal collection points. Inquire here at your municipal administration, the responsible town hall or a
local or municipal waste disposal company. Thanks very much.
Reproduction only with the permission of ChiliTec GmbH, teaching
Translated from German to English - www.onlinedoctranslator.com
operation manual EAR (WEEE): DE25841852
LUCID VerpackG: DE5562476395648
GRS (UBA Register) No.: 21003466
- Product data sheet-Page 2 of 2
WEEE reg. no. 25841852 Status: 01/2020 - Ver. 1.01
Installation (see also page 1 for safety instructions)
• Connection or installation may only be carried out by qualified electricians!
• For all work, completely switch off the circuit in which the installation is being carried out at
the main fuse!Otherwise there is a DANGER TO LIFE!!
• Attach the bracket to the mounting location.
• Connect the supply line according to the following figure. Before doing this, check once
again that your power supply is switched off at the main fuse!
• There are no serviceable parts inside this product.
• The correct connection must be checked, the voltage may only be switched on again if the
installation is faultless.
• The power circuit may only be put into operation when all components have been
professionally and securely installed in the wall/mounting/ceiling and have been
checked for full functionality.
• No installation on or near (50cm distance) combustible / flammable materials
(ignition temperature < 200°C). Also pay attention
Gas -/ dust -/ ambient air mixture. If necessary, ventilate the room thoroughly beforehand.
Assembly / Disassembly
connectivity
1.knob
2. Fixing nut
3. Coverage
A. Switching circuit
A1. toggle switch
A2. dimmer
FROM 3. Dimming range setting
Setting the basic brightness:
To set the basic brightness, set the rotary knob to the left stop (minimum brightness). Now use a
screwdriver to set the desired basic brightness on the potentiometer (No. 3). In accordance with
EN 60669-2-1 (8.6.102), the basic value must be set in such a way that the light shines visibly over
the entire load range (at a nominal voltage of 10%) when it is dark. If the dimmer stops working,
please check the connected lamps or the fuse installed in the dimmer? If necessary, replace the
fuse only with fuses of the same rating and the same type.
Reproduction only with the permission of ChiliTec GmbH, teaching
Questo manuale è adatto per i seguenti modelli
1
Indice
