Chipkin Mircom PRO2000 FS-8705-17 Manuale utente

ffffnbjjjjjj

salesgroup1@chipkin.com

Tel: +1 866 383 1657

Driver Version: 1.00a

Document Revision: 1

FS-8705-17 Mircom Pro2000 Serial Driver Page 2 of 32 
© 2021 CHIPKIN AUTOMATION SYSTEMS 
TABLE OF CONTENTS 
1MIRCOM PRO2000 FIRE ALARM PANEL SERIAL DRIVER DESCRIPTION.......................................................................................3 
2DRIVER SCOPE OF SUPPLY.........................................................................................................................................................5 
2.1 SUPPLIED BY FIELDSERVER TECHNOLOGIES FOR THIS DRIVER...................................................................................................................5 
2.2 PROVIDED BY THE SUPPLIER OF 3RD PARTY EQUIPMENT........................................................................................................................5 
 Required 3rd Party Hardware................................................................................................................................................5 
 Required 3rd Party Software .................................................................................................................................................5 
 Required 3rd Party Configuration..........................................................................................................................................5 
3HARDWARE CONNECTIONS.......................................................................................................................................................6 
3.1 HARDWARE CONNECTION TIPS /HINTS .............................................................................................................................................7 
4CONFIGURING THE FIELDSERVER AS A PRO2000 FIRE ALARM PANEL ACTIVE CLIENT ..............................................................10 
4.1 DATA ARRAYS/DESCRIPTORS .........................................................................................................................................................10 
4.2 CLIENT SIDE CONNECTION DESCRIPTIONS.........................................................................................................................................12 
4.3 CLIENT SIDE NODE DESCRIPTORS....................................................................................................................................................14 
4.4 CLIENT SIDE MAP DESCRIPTORS .....................................................................................................................................................15 
 FieldServer Related Map Descriptor Parameters ...............................................................................................................15 
 Driver Related Map Descriptor Parameters .......................................................................................................................16 
 Timing Parameters .............................................................................................................................................................16 
 Map Descriptor Example 1 .................................................................................................................................................17 
4.5 HOW POINT DATA IS STORED ........................................................................................................................................................18 
4.6 HOW MOST RECENT EVENT DATA IS STORED....................................................................................................................................18 
4.7 DRIVER LIMITATIONS AND EVENT PROCESSING..................................................................................................................................20 
 How to use the tool ............................................................................................................................................................23 
4.8 DRIVER LIMITATIONS....................................................................................................................................................................25 
5CONFIGURING THE FIELDSERVER AS A PRO2000 SERVER ........................................................................................................26 
6REVISION HISTORY..................................................................................................................................................................27 
 ADVANCED TOPICS.................................................................................................................................................28 
 DRIVER ERROR MESSAGES ...............................................................................................................................................28 
 DRIVER STATISTICS .........................................................................................................................................................30 
 Exposing Driver Stats .....................................................................................................................................................30 
 THE CLIENT SIDE OF THE CONFIGURATION ...........................................................................................................................31 
 

FS-8705-17 Mircom Pro2000 Serial Driver Page 3 of 32

1Mircom PRO2000 Fire Alarm Panel Serial Driver Description

The driver provides an interface to monitor a Mircom Pro2000 Fire Alarm Panel. It is able to read status data from the

panel –when combined with another protocol driver this data can be served using another protocol such as BACnet,

Lonworks, Johnson Controls N2, Rockwell, XML etc. A block diagram showing potential connectivity is provided below.

To avoid manual configuration the driver is provided with a utility that is used to aid in the creation of the FieldServer

configuration. This utility reads the PRO2000 Modbus CSV and uses this to make BACnet objects, for each device

connected to the system. One set of objects for each device is created –reporting the alarm, trouble and other status

info of the device. The Modbus CSV file is created when the panel is configured and is provided by the engineer who

configures the fire alarm panel.

This is an active client driver –it sends commands and polls and the panel responds with data.

The driver supports a small subset of the command/query functions and assumes the devices have been configured

correctly and appropriately to achieve the control required.

The driver can only be used as a client. Minimal server functionality is provided only to support our ongoing quality

assurance program by facilitating automated testing of the driver. It is not documented or supported.

Synchronization

No special steps are required for synchronization. On startup the driver will looked for new flagged events, thereafter it

will read the status of every device thus providing an automatic synch.

Driver Functionality

The driver continuously polls the panel reading a set of change flags. These flags are set by the panel when a device’s

status changes. Actually each flag may represent more than one device. The Pro200 refers to these groups of devices as

blocks. When a change flag is seen, the driver reads the set of data associated with the device that the change flag

represents. This can range from 1 to 100 devices. The quantity (block size) is determined by the panel configuration

engineer. When data associated with a change flag is read, the panel unsets the flag.

If more than one change flag is set this is how the driver operates. It reads, the data associated with the 1st one set. In

the next cycle, when it reads the change flags again, it will look for a change flag for a higher block number and then

read that block’s data. It only returns to look at the start of the change flags again when all the change flags have been

processed.

If no change flags are set, the driver will read the data for each device by reading the blocks of data associated with each

flag. In this mode, with no change flags set, the driver sequences through each block in turn and starts at the beginning

again.

Each device has 16 bits allocated to it. These bits report the status of the device. They are documented in this manual

but you should check with the manufacturer’s documentation in case there have been changes. This data can be

mapped onto any other FieldServer protocol such as BACnet or Modbus/TCP.

FS-8705-17 Mircom Pro2000 Serial Driver Page 4 of 32

Configuration Tool

CAS has developed a configuration tool to assist in the automation of the production of the configuration file. To obtain

a copy of the tool send an email to [email protected] and ask for the ‘Mircom Pro2000 configuration tool’.

Use of this tool eliminates the need to create the 16 potential objects for each device, eliminates the need to retype the

device labels etc. .. ie use it for productivity and accuracy.

The tool uses the data in the Modbus file to produce a portion of a FieldServer configuration. This is then added to the

base configuration file and the result is a complete configuration to map the panel data onto BACnet/IP objects.

Max Nodes Supported

FIELDSERVER MODE

NODES

COMMENTS

Active Client

Only one panel can be connected to a single FieldServer . If

this LIMITATION has significant impact for your project,

Active Server

(Simulate a PRO2000

Panel)

Not supported or documented.

FS-8705-17 Mircom Pro2000 Serial Driver Page 5 of 32

2Driver Scope of Supply

2.1 Supplied by FieldServer Technologies for this driver

FIELDSERVER

TECHNOLOGIES

PART #

DESCRIPTION

No specific cables are shipped with this driver.

A generic RJ45 Ethernet cable must be shipped with this driver.

A generic male and Female connector kit must be shipped with

this driver.

FS-8705-17

Driver Manual.

2.2 Provided by the Supplier of 3rd Party Equipment

Required 3rd Party Hardware

PART #

DESCRIPTION

Required 3rd Party Software

Required 3rd Party Configuration

None known.

FS-8705-17 Mircom Pro2000 Serial Driver Page 6 of 32

3Hardware Connections

Multiple upstream protocols and connection supported. See list of FieldServer Drivers.

Ethernet Network

Connection via std

networking interfaces

such as hubs, switches,

routers.

Lonworks

Device

RS232/RS485 Network

(Units with 1-8ports

available)

Lonworks Network

FS30 Series

Modbus

TCP

BACnet

IP BACnet

Ethernet

Rockwell

Ethernet/IP

CSP

HTTP

and other web

protocols

XML

Omron

Fins

GE-SRTP

GE-EGD

Other serial protocols

such as

Rockwell DF1

GE-SNP

JCI Metasys N2

Bacnet MSTP

Free BACnet test software with purchase*

Confidently test the BACnet interface.

Discover devices and their objects. Test

and document them. Arm yourself with a

powerful field tool. Full license.

We are always adding to

the library of protocols

and can add yours.

Monitor and Control Mircom PRO2000 FIre Panels using BACnet, Lonworks or a PLC system

MIRCOM

PRO2000 Series

Fire and Gas

Panels

FS-8705-17 Mircom Pro2000 Serial Driver Page 7 of 32

3.1 Hardware Connection Tips / Hints

Jack J4 Pinout

FS-8705-17 Mircom Pro2000 Serial Driver Page 8 of 32

MPU Switch Positions

Led’s for RS232

Mircom

Jack J4

(RJ11

Telephone

Jack)

FieldServer

RJ45

6 4

GE-TLC Direct Connect

to RJ111 to RJ45 Cable

Blue

Yellow

Green

Red

Black

White

Orange-White

Blue-White

Brown

Assembly Instructions

1. Cut one end off a

RJ45 Patch cable.

Jumper between 1,3 and 6.

Gnd

Cable Assembly –This cable is not provided.

FS-8705-17 Mircom Pro2000 Serial Driver Page 9 of 32

Mircom

Jack J4

(RJ11

Telephone

Jack)

Blue

Yellow

Green

Red

Black

White

Jumper between 1,3 and 6.

Gnd

DB9

Female

Cable Assembly –This cable is not provided.

FS-8705-17 Mircom Pro2000 Serial Driver Page 10 of 32

4Configuring the FieldServer as a PRO2000 Fire Alarm Panel Active Client

For a detailed discussion on FieldServer configuration, please refer to the FieldServer Configuration Manual. The

information that follows describes how to expand upon the factory defaults provided in the configuration files included

with the FieldServer (See “.csv” sample files provided with the FS).

This section documents and describes the parameters necessary for configuring the FieldServer to communicate with a

PRO2000 Panel.

4.1 Data Arrays/Descriptors

The configuration file tells the FieldServer about its interfaces, and the routing of data required. In order to enable the

FieldServer for FSC - Electronic Siren Controllers Serial Driver communications, the driver independent FieldServer buffers

need to be declared in the “Data Arrays” section, the destination device addresses need to be declared in the “Client Side

Nodes” section, and the data required from the servers needs to be mapped in the “Client Side Map Descriptors” section.

Details on how to do this can be found below.

Note that in the tables, * indicates an optional parameter, with the bold legal value being the default.

SECTION TITLE

Data_Arrays

COLUMN TITLE

FUNCTION

LEGAL VALUES

Data_Array_Name

Provide name for Data Array

Up to 15 alphanumeric

characters

Data_Array_Format

Provide data format. Each Data Array

can only take on one format.

Float, Bit, UInt16, Uint32,

SInt16, Packed_Bit, Byte,

Packed_Byte,

Swapped_Byte

Data_Array_Length

Number of Data Objects. Must be

larger than the data storage area

required by the Map Descriptors for

the data being placed in this array.

1-10,000

Indice

Manuali Pannello di controllo popolari di altre marche

RDZ

RDZ PC-HRX Manuale utente

STG-BEIKIRCH

STG-BEIKIRCH MZ3 Manuale tecnico

Efka

Efka Variocontrol V810 Manuale utente

Cebora

Cebora 208-10 Manuale utente

AMX

AMX AutoPatch CP-15 Manuale utente

Satel

Satel CA-6 KLED-S Manuale utente

Evolution

Evolution IQ plus 800 Manuale utente

Fagor

Fagor 8040 TCO CNC Manuale utente

Trane

Trane ComfortLink II XL950 Control Manuale utente

AKO

AKO PROCool AKO-17635-2 Manuale utente

ABB

ABB 6136/30M-101 Manuale utente

Telikou

Telikou BK-603 Belt Pack Manuale utente

Mapei

Mapei Mapeheat Thermo Touch Manuale utente

Bosch

Bosch D9412GV4 Manuale utente

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries SC-SL4-AE2/1 Manuale utente

Sminn

Sminn BOX L VF1L EI Manuale utente

Balboa

Balboa TP600 Manuale utente

Nice

Nice HSCU1 Specifiche tecniche