Chloride SGLO Manuale utente
July 2018
443580497441
Signify North America Corporation
200 Franklin Square Drive
Somerset, NJ 08873, USA
Phone: 855-486-2216
www.chloride-lighting.com
Signify Canada Ltd./Signify Canada Ltée.
281 Hillmount Road,
Markham, ON, Canada L6C 2S3
Phone: 800-668-9008
SGLO EDGE-GLO
EXIT
INSTALLATION AND
OPERATING
INSTRUCTIONS
IMPORTANT
SAFEGUARDS
When using electrical equipment, basic safety
precautions should always be followed, including
the following:
READ AND FOLLOW ALL
SAFETY INSTRUCTIONS
This sign shall be installed only where there is
adequate color contrast between the sign legend and
the interior wall finish behind the sign to provide
for sufficient visibility.
All servicing should be performed by qualified
personnel only.
Equipment should be mounted in locations and at
heights where it will not be readily subjected to
tampering by unauthorized personnel.
The use of accessory equipment not recommended
by the manufacturer may cause an unsafe condition.
Do not use this equipment for other than intended
use.
Do not use outdoors.
Do not let supply cords touch hot surfaces.
Do not mount near gas or electric heaters.
Use caution when servicing batteries. Battery acid
can cause burns to skin and eyes. If acid is spilled
on skin or eyes, flush acid with fresh water and
contact a physician immediately.
SAVE THESE
INSTRUCTIONS
WARNING – Shut off AC power to branch
circuits to which units will be connected. All
wiring should be per N.E.C. Articles 501-4(b)
and local codes.
To maintain warranty, equipment with batteries
must be installed or placed on charge within
prescribed period after shipment.
July,2018
443580497441
Signify North America Corporation
200 Franklin Square Drive
Somerset, NJ 08873, USA
Phone: 855-486-2216
www.chloride-lighting.com
Signify Canada Ltd./Signify Canada Ltée.
281 Hillmount Road,
Markham, ON, Canada L6C 2S3
Phone: 800-668-9008
GENERAL INSTRUCTIONS
Mounting Instructions
The SGLO surface mount fixture is designed to mount to any ceiling or wall conduit box by using the universal mounting plate.
Knockouts and mounting holes are also provided in the center of the top of the housing for mounting to the ceiling. Knockouts and
mounting holes are also provided in the center of one long side and one end for mounting to a wall.
Figure 1 provides an overall view of the fixture and shows all the critical dimensions. Refer to this illustration as you mount the
fixture.
1. Remove Edge-Glo Exit fixture and hardware from the box. Inspect contents to ensure that no damage occurred during
shipment.
2. Remove the two screws securing the wireway and remove the wireway from the housing.
3. Determine where the Edge-Glo fixture is going to be mounted.
4. Remove and retain the two screws from the conduit box. Orient the universal mounting plate to the conduit box so that the
studs align with the mounting holes in the fixture. Attach the plate using the screws removed from the conduit box. (The
universal mounting plate may not need to be used in ceiling mount installations. Use the plate if the conduit box plate does
not match the hole configuration in the housing).
5. Pull the AC feed wires through the center hole in the universal mounting plate.
6. Remove the appropriate knockouts from the housing depending on the mounting configuration.
7. Place the cover plate over the universal mounting plate as shown in Figure 2. (The cover plate does not need to be used in
ceiling mount applications).
July,2018
443580497441
Signify North America Corporation
200 Franklin Square Drive
Somerset, NJ 08873, USA
Phone: 855-486-2216
www.chloride-lighting.com
Signify Canada Ltd./Signify Canada Ltée.
281 Hillmount Road,
Markham, ON, Canada L6C 2S3
Phone: 800-668-9008
8. Pull the AC feed wires into the housing.
9. Secure the housing to the mounting plate with two lockwashers and nuts.
10. Using wire nuts (not supplied) connect wires from the wireway to the AC feed. Connect Green wire to ground, White wire to
Common, and Black wire to 120VAC or Blue Wire to 277VAC (cap off unused wire to prevent shorting).
11. Reattach the wireway to the housing using the two screws removed in Step 2.
12. To install the EXIT panel, squeeze the ends of each torsion spring together and insert the ends into the slots in the wireway.
Slowly release the springs, making sure that they stay in the slots. Carefully push the panel into place.
13. Energize the AC circuit and ensure that the fixture lights.
Altri manuali Chloride Attrezzatura di sicurezza
