ci D-200 MKII Manuale utente
D•200 MKII Class D Monoblock Amplifier
Thank you for purchasing the D•200 MKII Power Amplifiers. These products are proudly
designed, assembled, and tested in the USA. We hope they will provide you with many years of
musical enjoyment.
Please read the entire contents of this manual before making connections to your audio
system.
Design
The D•200 MKII represents the latest in Class D audio amplifier technology.
At the AC Input, we use our smooth-start circuit, which eases the start-up tasks, then to our
XDC•2 circuit to eliminate any DC voltage riding on your AC line. Power is then fed to our
custom multiple-output power transformer, then rectified by discrete Schottky diode bridges.
Several individual voltages are then filtered and regulated to provide power to various circuits.
The output circuit is unregulated with over 40,000uF of capacitance.
The amplification circuit is a custom UcD design with power output of
200 watts into 8 ohms / 375 watts into 4 ohms. This design is 90% efficient at full power and
produces little heat (wasted energy). The small amount of heat generated by the amplifier is
dissipated by the machined aluminum chassis acting as a heat-sink.
This low operating temperature means the internal components aren't subject to the heat
cycles of traditional amplifiers, yielding better reliability, more consistent performance, and
longer life.
Specifications
Power Output: 200 watts @ 8 ohms/375 watts @ 4 ohms
Bandwidth: 50kHz
Frequency Response: 10Hz - 20kHz, +0dB/-0.5dB
Damping Factor: >1000
Input Impedance: 100k ohms
Gain: 32db (for use with VPC, PLC or other passive preamplifiers)
or 26db (for use with active preamplifiers)
Dimensions:8.5"w x 4.0"h x 13.5"d
Weight: 28 lbs (each)
Connecting your D•200's
TRIGGER
AC INPUT
SPEAKER
handcrafted in USA
Positive Speaker Output
Negative Speaker Output
RCA Signal Input
XLR Signal Input
Fuse
Remote Trigger Control
RoHS
XXXXXX
Serial Number
CAUTION
Signal Input
Connect your Left & Right signal to the respective input of each amplifier.
The toggle switch should be in the "up" position for use with RCA input, and "down" for use
with the XLR input (as shown below).
RCA XLR
Speaker Output
Next connect your speakers to the respective amplifiers. The "+" binding post is marked in red
and should be connected to the "+" terminal of the loudspeaker. The "-" binding post is marked
in black and should be connected to the "-" terminal of the loudspeaker.
12v Trigger
The 12 volt DC trigger feature can be used to remotely mute/play your D•200's. Two ports are
provided, allowing a daisy-chain of several amplifiers.
To make use of this feature, you will need our PLC•1 or similar device, which supports this
feature.
OUTPUT TAPE INPUT
L
R
L
R
21 OUT IN 4 3 2 1
TRIGGER
OUTPUT
14V AC
INPUT
handcrafted in USA
TRIGGER
AC INPUT
SPEAKER
handcr af ted in U SA
RoHS
XXXXXX
Serial Number
CAUTION
TRIGGER
AC INPUT
SPEAKER
handcr af ted in US A
RoHS
XXXXXX
Serial Number
CAUTION
AC Power
Before connecting AC power to your D•200's, put them in "mute" as described below. When
power is connected, you will hear a "click" as the SmoothStart circuit is engaged.
Front Panel Switch/Indicator
The front panel switch is used to alternate between "play" and "mute". When the button is in
the "out" position, the amplifier output is in “mute”. In this state, the input stage is being
powered but the output stage is turned off.
When the button is in the "in" position, the amplifier is in “play” mode, and the blue LED ring
will illuminate.
If using the 12v trigger option, leave the amplifier in "mute" and the remote trigger function
will control the mute/play state of the amplifiers. When turned on by the 12v trigger, the blue
LED ring will illuminate.
Maintenance
D•200 is essentially maintenance free other than occasional cleaning.
Always disconnect the amplifier from power prior to cleaning. The exterior can be cleaned with
a soft cloth moistened with window cleaner. Never apply liquids directly to the aluminum
surface.
Fuses
Standard AC line fuses are used to protect the amplifier. Fuses are located in the AC input block
above the power cord inlet. Each fuse holder houses a spare fuse in case of failure.
Always disconnect from AC power before checking or changing fuses.
D•200 MKII Fuse Ratings
4.0A/250V Fast Acting GBD Series (5mm x 20mm)
(Use for AC Input 100V~120V)
3.15A/250V Fast Acting GBD Series (5mm x 20mm)
(Use for AC Input 220V~240V)
Warranty
Your CIAudio product is covered by a 5 year Parts & Labor Warranty. For warranty service or
technical support, contact us at…
Channel Islands Audio
567 W. Channel Islands Blvd.
PMB #300
Port Hueneme, CA 93041
Phone (805) 984-8282
www.ciaudio.com
Indice
Altri manuali ci Amplificatore
