Cisco UC500 series Guida all'installazione

Smart Business Communications System

Unified Communications 500 Series

SBCS/UC500 – “First Look”

Rev 1.4

Hands On Technical Training

Lab Guide

Labs by

SBCS/UC500 Technical Marketing Team

Cisco Unified Communications Technical Training

Page 2 of 171

Table of Contents

Lab Topology.............................................................................................................................................. 4!

Lab Overview.............................................................................................................................................. 5!

LAB 1: Plug & Play.................................................................................................................................... 6!

LAB 2: PBX, Voicemail & DialPlan.......................................................................................................... 8!

LAB 3: Business Schedule and Auto Attendant....................................................................................... 23!

LAB 4: Advanced Feature Lab................................................................................................................. 39!

LAB 5: Verifying VoiceViewExpress & IMAP....................................................................................... 61!

LAB 6: Basic ACD ................................................................................................................................... 67!

LAB 7A: Security on UC500 and SR520................................................................................................. 71!

LAB 7B: Wireless................................................................................................................................... 106!

LAB 7C: Wireless setup wizard with SPA525G Phones........................................................................ 110!

LAB 8A: Configuring IPSEC VPNs between sites on the UC520......................................................... 132!

LAB 8B: UC520 Multi-Site Setup.......................................................................................................... 133!

APPENDIX A: Reset to factory default ................................................................................................. 146!

APPENDIX B: Key System w/ Voicemail............................................................................................. 147!

APPENDIX C: PPPoE on the WAN ...................................................................................................... 155!

APPENDIX D: IOS Dial-peer configuration via CLI ............................................................................ 158!

APPENDIX E: Designing for a Scenario ............................................................................................... 166!

APPENDIX F: Device Manager Cross Launch...................................................................................... 167!

Cisco Unified Communications Technical Training

Page 3 of 171

Start Here

The following lab guide offers step-by-step instructions on how to configure the Unified

Communications 500 System (UC500) using a base topology.

The different tasks are collaborative and assume that several PODs have been set up simultaneously.

However, some exercises can still be completed individually.

Each lab section follows a logical sequence, but is independent from the others, with the exception of

Lab 1 (Plug and Play), which is a prerequisite for the successful completion of the subsequent exercises.

Here is a short description of each lab:

Lab 1 – Plug and Play: Learn how the UC500 implements automatic phone registration and

configuration.

Lab 2 – PBX Mode: Learn how to implement PBX mode and what features are available for it.

Lab 3 – Auto Attendant: Learn how the Cisco Unity Express (CUE) Automatic Attendant is

configured.

Lab 4 – Advance Features: Learn how to configure Conferencing, Intercom, Hunt Groups, etc.

Lab 5 – VoiceView Express and IMAP: Learn how to integrate the UC500 with an email client using

IMAP and how to configure VoiceView Express, for checking voicemail using the IP Phone menus.

Lab 6 – Basic Automatic Call Distribution: Learn how to implement Call Center features using B-

ACD Scripts.

Lab 7A – Security: Firewall configuration for UC500

Lab 7B – Wireless Mobile Voice: Deploying the 792X Wi-Fi IP Phone

Lab 7C – Wireless Voice: Deploying the SPA525 IP Phone in wireless mode and adding AP521

Access Point.

Labs 8A and 8B cover Multisite Data using IPsec and multisite voice (no IPsec)

Appendixes A, B, C, D, E and F cover miscellaneous voice and data features, as well as system

operation. Lab Topology.

Cisco Unified Communications Technical Training

Page 4 of 171

Lab Topology

The value “xx” should be set to the POD number that you have (goes from 01 to 12)

WAN IP addressing:

WAN IP Address

1.1.100.xx

WAN Subnet Mask

255.255.255.0

WAN Default Router

1.1.100.254

Inbound SIP Trunk DID (PSTN Call in) Numbers (Use PSTN phone to test)

Auto attendant

4085xx1200

Extension 1 (201)

4085xx1201

Extension 2 (202)

4085xx1202

VoiceMail

4085xx1209

Outbound Numbers to Call (From IP Phones on UC520 to PSTN Phone)

Emergency Number

9911

Local Call

9 777 1000

Long Distance

9 1 650 7772000

International

9 011 44 1234512345

UC520

CCA

FXO 0/1/0 to FXS 0/0/0

FXS 0/0/0 to FXO 0/1/0

Simulated

Internet &

SIP Trunk

Even

POD

Odd POD

PSTN

CCA

Lab Overview

Be sure to turn off your wireless adaptor before completing the labs to avoid routing issues. An

Ethernet connection from your laptop to the UC500 / lab network should be the only network

connection.

In the lab documents, ‘xx’ refers to your Pod number. For example, if you are seated at POD01, you

would replace all instances of ‘xx’ in the lab documents with ‘01’.

Several of the labs will require you to partner with another pod to demonstrate certain features of the

system. This is to emulate an analog PSTN connection for the lab environment. Normally, you would

plug trunks from the PSTN into the FXO or ISDN ports and analog devices (such as fax machines) into

the FXS ports. Please be sure and coordinate with the team seated at your ‘buddy’ pod so that you are

both working on roughly the same portion of a lab and can complete the verification steps successfully.

One of the labs requires an analog phone for completion. There is only a single analog phone for each

pair of Pods. Please share the phone between yourselves and your ‘buddy’ pod.

There are two Ethernet cables at each pod. These are both ‘broadband internet’ connections (emulating

the internet). One of these is for the UC500 WAN port, the other is used during the VPN lab to connect

your laptop. Either cable will work for either connection – there is no difference between them.

All of the software needed on your laptops to complete the lab is available from the lab facilitator.

Please copy all of this software to your hard drive before the lab begins so you will have it when needed.

This software will include the Cisco Configuration Assistant (CCA), Cisco IP Communicator (CIPC),

Cisco VPN Client and the new auto attendant (AA) script.

Unless otherwise noted, it is necessary to restore the UC500 to factory default condition after each lab

section. Instructions for how to do this are included in Appendix A.

Please read items in RED very closely. These are notes / tips that will make the lab go much more

smoothly.

LAB 1: Plug & Play

Introduction:

UC520 is a unified communications appliance that is designed to be deployed quickly and easy. To help

facilitate this, the system automatically detects phones as they are connected and configures them with

basic default settings that allow calls to be made without intervention. For instance, if a 7960G phone is

plugged in, the system detects the type of the phone and auto configures a useable extension on the first

line button.

Objective:

The objective of the “PLUG & PLAY” lab is to show the ease of install of the UC520 system. At the

completion of this lab, all IP phones (including the CIPC softphone) and analog phones on the UC520

should get dial tone and be able to call each other. You should be able to call out as well if a PSTN

connection is available via a FXO or ISDN lines.

Topology:

Use the following topology

Setup steps:

Be sure to turn off your wireless adaptor before completing the labs to avoid routing issues.

The only network connection from your laptop should be to the UC500 / lab network.

1. Be sure your UC500 system is powered up, then plug one of the “Internet” cables into the WAN

port.

2. Plug in the 7970 and 524 phones in to the UC520 Power Over Ethernet (POE) ports at each POD

using the Ethernet cables provided.

3. Connect your laptop to the back of an IP phone or to a POE port on the UC500. Verify that you

get an IP address assigned to the laptop.

4. After both 7970 and 524 IP Phones have registered to the UC500, install and launch Cisco IP

Communicator (CIPC) SoftPhone on your laptop.

UC520

LAB 1: Plug & Play

Cisco Unified Communications Technical Training

Page 7 of 171

a. After launching CIPC, a Preferences Screen will appear (Right click on the CIPC to view

preferences if it does not appear). Now configure specific TFTP server on the network

tab as the UC520 IP address (192.168.10.1).

Verify steps:

1. Ensure that all the phones register to the UC520 and receive an extension. Verify the extensions

as 201, 202 and 203 (CIPC)

2. Place a call between 201 & 202 – answer the call, place on HOLD and check if the Music on

Hold (MOH) works.

3. Place a call between 201 and CIPC (x203). Answer the call and place on hold on the IP

Communicator and note that the music plays to the IP phone. Take the call off hold and place it

on hold on the IP phone. Note that the IP Communicator only hears a hold tone and not the

MoH source.

NOTE: It is NOT necessary to restore the system to factory defaults at the end of

this lab.

LAB 2: PBX, Voicemail & DialPlan

Introduction:

The UC520 supports two voice system configuration types – PBX type and Keysystem type. LAB2

focuses on the PBX system configuration. Keysystem configuration is included as an addendum in

Appendix B. Outbound calls are routed through the SIP and/or PSTN line based on the dialplan that is

configured. In addition to this, local extensions have voicemail boxes where callers can leave messages.

A typical PBX system involves an Auto Attendant that handles incoming calls from a PSTN line (eg.

Analog FXO or ISDN trunks) and transfers the caller to one of the internal extensions. Auto Attendant

configuration is covered in Lab xx.

Objective:

The main objective of this lab is to configure the basic PBX system, voicemail and outbound dialplan.

These features will be configured using Cisco Configuration Assistant (CCA). After completion of this

lab – you will be able to:

a) setup the SBCS system as a PBX

b) place calls between extensions

c) setup a SIP Trunk on the UC520 to a Service Provider (Lab Simulation)

d) place calls in & out to the PSTN via the SIP trunk.

Topology:

Setup steps:

1. Install Cisco Configuration Assistant (CCA) on your laptop.

2. Connect your laptop to one of the UC520 Ethernet ports or the Ethernet connection on the back of an

IP phone (if not already connected) & launch CCA.

UC520

CCA

PSTN

SIP Trunk

Service

Provider

WAN

LAB 2: PBX, Voicemail & DialPlan

Cisco Unified Communications Technical Training

Page 9 of 171

3. When you launch CCA, a Connect window will appear. Click on “Create community” and click on

OK button.

4. Now you should see a dialog as below:

oCreate a community UC520-xx. For the Company name, use POD-xx (where ‘xx’ is your Pod #)

oChoose discover option as “a single device by IP address” and use IP address 192.168.10.1

oClick Start - now you should get a “Security Certificate Alert”, click ‘Always’.

oEnter username/password as cisco/cisco.

LAB 2: PBX, Voicemail & DialPlan

Cisco Unified Communications Technical Training

Page 10 of 171

oOnce discovery is complete (this may take up to a minute) click ‘OK’ to view the topology. The

progress for discovery can be seen at the bottom of the screen.

oCheck the topology to ensure all the phones show up. You may or may not see the CIPC device,

depending on where your laptop is plugged in. If it is plugged into a POE port of the UC520, the

CIPC will appear. If the laptop is plugged into the back of an IP phone, the CIPC will not appear.

oClick on ‘Configure -> Telephony -> Voice’ on the side bar or click the ‘Phone’ icon on the top

menu bar. In the next steps, we will configure the various tabs – “System”, “Voicemail”, “SIP

Trunk”, “Dial Plan” and “Users”.

NOTE: It may take up to 60 seconds for CCA to load voice data. If

you see the window below, please follow the instructions in the

Altri manuali per UC500 series

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Cisco Sistema di conferenza

Cisco

Cisco 3200 Series Manuale utente

Cisco

Cisco TelePresence SX20 Manuale utente

Cisco

Cisco TelePresence SX20 Manuale di servizio

Cisco

Cisco Quick Set C20 Istruzioni per il montaggio

Cisco

Cisco TelePresence SX10 Manuale di servizio

Cisco

Cisco TelePresence SX10 Manuale di servizio

Cisco

Cisco TelePresence Touch 10 Manuale utente

Cisco

Cisco EX60 Manuale utente

Cisco

Cisco TelePresence MX Series Manuale di servizio

Cisco

Cisco Telepresence MX800 Manuale utente

Cisco

Cisco Webex Room Kit Pro Manuale utente

Cisco

Cisco TelePresence DX80 Manuale utente

Cisco

Cisco TANDBERG Edge MXP Istruzioni per il montaggio

Cisco

Cisco Codec C Series Manuale utente

Cisco

Cisco Webex Room Kit Plus Precision 60 Manuale utente

Cisco

Cisco EX60 Manuale di servizio

Cisco

Cisco TelePresence IX5200 Manuale utente

Cisco

Cisco 500 Series Manuale utente

Cisco

Cisco EX90 Manuale utente

Cisco

Cisco Catalyst 3000 Manuale utente

Cisco

Cisco Telepresence MX800 Manuale utente

Cisco

Cisco Webex Codec Pro Manuale utente

Cisco

Cisco TelePresence MX700 Manuale utente

Cisco

Cisco TelePresence DX80 Manuale utente

Manuali Sistema di conferenza popolari di altre marche

Kramer

Kramer VIA GO Manuale utente

AVT

AVT MAGIC AC1 Go Manuale utente

ProSoft Technology

ProSoft Technology AN-X4-AB-DHRIO Manuale utente

Sony

Sony PCS-I150 Manuale utente

Middle Atlantic Products

Middle Atlantic Products VTC Series Manuale utente

Prentke Romich Company

Prentke Romich Company Vanguard Plus Guida

Speakerbus

Speakerbus iD 712 Manuale utente

Trelleborg

Trelleborg SafePilot CAT PRO Manuale utente

Sennheiser

Sennheiser ADN Manuale utente

ADTRAN

ADTRAN NetVanta 7100 Manuale utente

AINA

AINA PTT Voice Responder Manuale utente

Yamaha

Yamaha ProjectPhone PJP-100H Manuale utente

vissonic

vissonic VLI Series Manuale utente

Panasonic

Panasonic KX-VC500 Manuale utente

Poly

Poly Trio 8300 Manuale utente

Crestron

Crestron Mercury CCS-UCA-SMK Disegno dimensionale

Inmarsat

Inmarsat mini M Manuale utente

Tenveo

Tenveo ALL-IN-ONE Manuale utente