Cisco 2100 Series Manuale utente

TAKE OUT WHAT YOU NEED

RACK MOUNT THE HARDWARE

CONNECT CABLES

RUN THE SETUP PROGRAM

Quick Start Guide

CISCO INTELLIGENCE ENGINE 2100 SERIES

MOUNTING, CABLING, AND SETUP

MODE

Cisco Intelligence Engine 2100 Series

Routers

Console

Hub

53002

DRIVE0DRIVE1

MODE

Take Out What You Need

This guide explains how to mount, cable, and set up

your Cisco Intelligence Engine 2100 Series

(IE2100 Series).

Product Documentation

1 Quick Start Guide (this guide)

1 Regulatory Compliance and Safety Information

for Cisco Intelligence Engine 2100 Series

1 Cisco Intelligence Engine 2100 Series

Configuration Registrar Manual (for more detailed

information about subjects covered in this guide)

1 Release Notes for Cisco Intelligence Engine 2100

Series Configuration Registrar

Hardware Appliance

1 Cisco Intelligence Engine 2100 Series

53000

Intelligence Engine 2100 Series

LINK

CONSETHERNET0 ETHERNET1

100MbpsLINK100MbpsDRIVE0 DRIVE1

MODE

Take Out What You Need (continued)

Cables and Power Cord

1 yellow Ethernet 10BaseT cable

(to connect to a 10BaseT hub)

1 flat, light-blue console cable with

1 RJ-45 adapter, labeled TERMINAL

(RJ-45-to-DB-9)

1 black power cord

Rack-Mount Kit

2 L mounting brackets (left and right)

4 M4 Phillips countersunk-head screws

4 12-24 x 3/4-inch Phillips binder-head screws

4 10-32 x 3/4-inch slotted binder-head screws

1 8-32 x 1/2-inch black Phillips binder-head screw

Desktop-Mount Kit

4 Desktop mounting self-adhesive feet

Rack Mount the Hardware

49336

Intelligence Engine 2100 Series

LINK

CONS ETHERNET 0 ETHERNET 1

100Mbps LINK 100MbpsDRIVE 0 DRIVE 1

MODE

Phillips machine

screws

Installing Rack Mount

Hardware

This section describes how to install the

IE2100 Series in a standard 19-inch equipment rack.

A rack-mount kit is included for mounting the

system in a standard 19-inch equipment rack with

two unobstructed outer posts.

Note You can place the system on a desktop or other

flat, stable surface. Self-adhesive rubber feet are

provided for this purpose.

Warning The following guidelines are

provided to ensure your safety:

• This unit should be mounted at the bottom of

the rack if it is the only unit in the rack.

• When mounting this unit in a partially filled

rack, load the rack from the bottom to the top

with the heaviest component at the bottom of

the rack.

• If the rack is provided with stabilizing devices,

install the stabilizers before mounting or

servicing the unit in the rack.

To install the IE2100 Series in a rack:

Step 1 Measure the rack to verify that the system

will fit.

Step 2 Attach the L brackets to the sides of the

chassis using the provided screws so that

the L-bracket mounting surfaces are even

with the front or back panel of the chassis,

depending on which way you want to

install it.

Step 3 Position the chassis in the rack.

Step 4 Align the four mounting holes in the

L bracket with the four mounting holes in

the equipment rack.

Step 5 Secure the system in the rack by installing

the provided screws through the elongated

holes in the L bracket and into the

threaded holes in the mounting post.

Connect Cables

MODE

Cisco Intelligence Engine 2100 Series

Routers

Console

Hub

53002

DRIVE0DRIVE1

MODE

Connecting the Ethernet and

Console Cables

Use the console cable in the accessory kit to connect

the IE2100 Series console port (CONS) to a console or

computer that is running a console program.

Use the CAT 5 UTP cable in the accessory kit to

connect the IE2100 Series to your network.

Cisco Intelligence Engine 2100 Series

Console cable

Console

Cons Port (RJ-45)

53006

Intelligence Engine 2100 Series

LINK

CONSETHERNET0 ETHERNET1

100MbpsLINK100MbpsDRIVE0DRIVE1

MODE

Cisco Intelligence Engine 2100 Series

Ethernet Hub

(sold separately)

CAT 5 UTP cable

Ethernet 10/100BaseTX

port (RJ-45)

53005

Intelligence Engine 2100 Series

LINK

CONSETHERNET0 ETHERNET1

100MbpsLINK100MbpsDRIVE0 DRIVE1

MODE

Connect Cables (continued)

AC power

connector

49334

Power switch

Power receptacle

Connect the Power Cable

Step 1 Verify that the Power switch is set to OFF.

Step 2 Connect the black power cable to the

power receptacle on the rear panel of the

IE2100 Series.

Step 3 Connect the other end of the power cable

to an AC power source.

Step 4 Set the power switch to ON.

Step 5 Verify that the IE2100 Series is

operational.

Run the Setup Program

This section explains how to run the setup program

to configure the system.

Step 1 Boot the system without a configuration.

When the system finishes booting, a login

prompt appears.

Step 2 Log in with the username of setup.

Step 3 Enter responses to the prompts that appear:

hostname

System hostname. Appears in command

prompt.

domain name

System domain name.

admin password

Password for the Linux administrative

user account on the IE2100 Series; case

sensitive, between 5 and 20 characters.

confirm password

Reenter password to verify that you typed

it correctly.

eth0 IP address

IP address of Ethernet 0 interface.

eth0 network mask

Network mask of Ethernet 0 interface.

eth0 default gateway IP address

IP address of default router that connects

IE2100 Series to network.

eth1 IP address

Optional. To skip, press Enter.

eth1 network mask

Optional. To skip, press Enter.

eth1 default gateway IP address

Optional. To skip, press Enter.

Primary DNS nameserver IP address

IP address of DNS server that

IE2100 Series uses for name/IP-address

resolution.

Secondary DNS nameserver IP address

Optional. To skip, press Enter.

enter country code

Enter the two (2) character country code.

enter Location code

Enter the location code or name without

embedded blanks.

enter Configuration Server username

Username for the Configuration Registrar

administrative account; case-sensitive

with a maximum of 32 characters.

<username> password

Password for the administrative user

account on the Configuration Registrar;

case sensitive, between 5 and 20

characters.

confirm password

Reenter password to verify that you typed

it correctly.

Would you like to save this configuration

[yes]

Press Enter to accept the configuration.

The configuration is saved.

Step 4 Log in as admin.

Step 5 Type rootenable.

Step 6 Set your root password.

Caution If you forget your root password,

you will be locked out of the system!

Run the Setup Program (continued)

Verify Configuration Registrar

is Running

Once the system has been installed and configured,

you can verify the installation of the Configuration

Registrar by following these steps:

Step 1 Go to a different computer and bring up a

web browser.

Step 2 On the net-site window enter the URL for

the Configuration Registrar.

For example:

http://<ip_address>/config/login.html

where: ip_address is the IP address you

entered during IE2100 Series setup.

The Configuration Registrar login page

appears.

Step 3 Enter the Configuration Registrar Userid

and Password that you entered during

IE2100 Series setup.

Step 4 On the message page, click Continue.

If you have reached the Configuration

Registrar Home page, you have verified the

successful installation on the Configuration

Registrar.

Altri manuali per 2100 Series

Indice

Altri manuali Cisco Firewall

Cisco

Cisco Firepower 2100 Series Manuale utente

Cisco

Cisco RV110W Manuale utente

Cisco

Cisco 5510 - ASA SSL / IPsec VPN Edition Manuale utente

Cisco

Cisco Cisco ASA 5500 Series Manuale utente

Cisco

Cisco FirePOWER 7000 Manuale utente

Cisco

Cisco Small Business RV215W Manuale utente

Cisco

Cisco S190 Manuale utente

Cisco

Cisco RV110W Manuale di istruzioni

Cisco

Cisco 5505 - ASA Firewall Edition Bundle Manuale utente

Cisco

Cisco ISA 3000 Manuale utente

Cisco

Cisco 5505 - ASA Firewall Edition Bundle Manuale

Cisco

Cisco Firepower 4100 Series Manuale utente

Cisco

Cisco 5510 - ASA SSL / IPsec VPN Edition Manuale utente

Cisco

Cisco 515E - PIX Restricted Bundle Manuale utente

Cisco

Cisco Cisco ASA 5510 Manuale utente

Cisco

Cisco Firepower 4100 Series Manuale di installazione e funzionamento

Cisco

Cisco ASA 5506-X Manuale utente

Cisco

Cisco Firepower 1010 Manuale utente

Cisco

Cisco MEREAKI MX65W Manuale utente

Cisco

Cisco 5505 - ASA Firewall Edition Bundle Manuale

Cisco

Cisco LightStream 1010 Manuale di istruzioni

Cisco

Cisco RV110W Manuale utente

Cisco

Cisco Firepower 7010, Firepower 7020, Firepower 7030, Firepower 7050, Firepower 7110, Firepower 7120, Firepower 7115, Firepower... Manuale utente

Cisco

Cisco PIX 501 Manuale utente

Manuali Firewall popolari di altre marche

Fortinet

Fortinet FortiGate Voice Series Manuale utente

ADTRAN

ADTRAN NetVanta 2300 Manuale utente

SecureLogix

SecureLogix ETM System Manuale utente

NETGEAR

NETGEAR ProSafe FVX538 Manuale utente

Lanner

Lanner FW-8877 Manuale utente

Huawei

Huawei USG6000 Series Manuale di installazione e funzionamento

H3C

H3C SecPath F5000-AI-15 Manuale utente

Nexcom

Nexcom DNA 1150 Manuale utente

Fortinet

Fortinet FortiGate-60 series Manuale utente

Draytek

Draytek Vigor2860 Series Manuale utente

Lanner electronics

Lanner electronics FW-7650 Series Manuale utente

Swisscom

Swisscom Internet Backup Manuale utente

SonicWALL

SonicWALL NSa 5700 Manuale utente

DPtech

DPtech FW1000 SERIES Manuale utente

FEITIAN

FEITIAN MultiPass FIDO Manuale utente

EBLOCKER

EBLOCKER PRO Manuale utente

GTA

GTA GB-200 Manuale utente

Trend Micro

Trend Micro Deep Edge Manuale utente