Cisco LINKSYS RFC 2364 Manuale utente

QUICK INSTALLATION GUIDE

ADSL Gateway

There are two ways to set up the Gateway, run the

Setup CD-ROM or use this Quick Installation. Linksys

strongly recommends that you run the Setup CD-ROM.

Run the Setup CD-ROM

Insert the Setup CD-ROM into the CD-ROM

drive, and follow the on-screen instructions.

Use this Quick Installation

Follow the instructions in this Quick

Installation. This method should only be

used if you cannot run the Setup CD-ROM.

Installation1

Make sure that all the devices that you are working with are poweredA.

down, including your computer(s) and the Gateway. If you have a

modem connected to your network, disconnect it. The Gateway

replaces your modem.

B. Connect one end of the

provided Ethernet cable to your

computer’s Ethernet adapter.

Connect the other end of the

Ethernet cable to one of the

Ethernet ports on the back of

the Gateway.

Repeat step B for every computer or device that you want to connect toC.

the Gateway via Ethernet. If you connect more than four computers to

the Gateway, then you also need to connect a switch to the Gateway.

NOTE: If your computer’s Ethernet adapter is not set up,

refer to the Ethernet adapter’s documentation for more

information.

D. Connect one end of the phone

cable to the DSL port on the

back of the Gateway.

Connect the other end of theE.

phone cable to the wall jack

with ADSL service or microfilter.

NOTE: To avoid interference, you may need to place a

microlter or splitter between the phone cable and wall

jack. Contact your ISP to determine if one is required. (UK

residents need to connect the microlter to the wall phone

jack with ADSL service, and then connect one end of the

provided phone cable to the DSL port on it.) If you have more

than one phone and you experience static on the line after

installing the Gateway, then you need to install an additional

microfilter for each phone or fax that you use. If you use

ISDN, then you do not need a microlter.

Connect the Computer

Connect the DSL

F. Connect the power adapter to

the Gateway’s power port and

the electrical outlet.

Power on the computer thatG.

you want to use to configure the

Gateway.

The Power, Wireless, and at least one of the numbered Ethernet (1, 2, 3,H.

or 4) LEDs should light up. If not, make sure the Gateway is powered on

and the cables are securely connected.

Connection is complete. Go to Step 2: Configuration.

Configuration2

In step 2, configure the Gateway to access the Internet through your ADSL

Internet Service Provider (ISP). Use the setup information provided by your

ISP.

NOTE: You only need to congure the Gateway once.

A. Open your web browser. Enter

http://192.168.1.1 in the web

browser’s Address field. Press

Enter.

B. On the login screen, enter

admin in lowercase letters

in both the User name and

Password fields (admin is

the default user name and

password). Click OK.

TheC. Basic Setup screen appears. Refer to the settings provided by your

ISP. Select the Encapsulation method your ISP has specified.

For the Multiplexing setting, selectD. LLC or VC.

Conexão da alimentação

Access the Web-Based Utility

For the Virtual Circuit, enter the VPI and VCI settings.E.

Proceed to the appropriate instructions for your Encapsulation method.F.

Enter the following settings unless otherwise instructed by your ISP.

Encapsulation Settings by Country

Country Encapsulation Multiplexing VPI VCI

Australia PPPoE LLC 8 35

New Zealand PPPoA VC 0 100

UK PPPoA VC 0 38

RFC 2364 PPPoA or RFC 2516 PPPoE

Enter your User Name and1.

Password.

2. Select Keep Alive if you always

want to be connected to your

ISP, or select Connect on

Demand if you are charged

for the time that you are

connected to your ISP.

Click3. Save Settings.

RFC 2364 PPPoA

RFC 2516 PPPoE

RFC 1483 Routed or IPoA

1. Enter the IP Address, Subnet

Mask, and Default Gateway IP

address.

In the2. Primary and/or

Secondary DNS elds, enter at

least one DNS IP address.

Click3. Save Settings.

RFC 1483 Bridged - Dynamic IP Address

1. For the IP Setting, select

Obtain an IP Address

Automatically.

Click2. Save Settings.

RFC 1483 Routed

IPoA

RFC 1483 Bridged - Dynamic IP Address

For additional information or troubleshooting help, refer to the User Guide on the CD-ROM.

Additional support is also available by phone or online.

Website

http://www.linksys.com/international

Australia

http://www.linksys.com/au/registration

Product Registration

United Kingdom

http://www.linksys.com/uk/registration

New Zealand

http://www.linksys.com/nz/registration

RFC 1483 Bridged - Static IP Address

1. For the IP Setting, select Use

the Following IP Address.

Enter the IP Address, Subnet2.

Mask, and Default Gateway IP

address.

In the3. Primary and/or

Secondary DNS elds, enter at

least one DNS IP address.

Click4. Save Settings.

Bridge Mode Only

Use this mode only if you are

using the Gateway as a bridge,

which makes the Gateway act

like a stand-alone modem. Click

Save Settings.

In the web browser’sG. Address field, enter the appropriate website:

www.linksys.com/uk/registration (United Kingdom),

www.linksys.com/au/registration (Australia), or

www.linksys.com/nz/registration (New Zealand). Then press Enter.

NOTE FOR WIRELESS GATEWAYS: Refer to the User Guide

on the CD-ROM for instructions on wireless conguration.

Linksys recommends that you change the default wireless

settings and enable the appropriate security method.

Congratulations! The installation of the Gateway is complete.

RFC 1483 Bridged - Static IP Address

Bridge Mode Only

8031010NC-RR

Altri manuali per LINKSYS RFC 2364

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Cisco Portale

Cisco

Cisco ISDN GW 3241 Manuale utente

Cisco

Cisco AS5400XM Manuale utente

Cisco

Cisco Explorer 4250 Manuale utente

Cisco

Cisco DPR2320 Istruzioni operative

Cisco

Cisco Linksys WAG160N Manuale utente

Cisco

Cisco Meraki Z3C Manuale utente

Cisco

Cisco ATA 188 Manuale di servizio

Cisco

Cisco Connected Life CLG-8202-WW Manuale utente

Cisco

Cisco Expressway CE1000 Appliance Manuale utente

Cisco

Cisco Comcast Xfinity DPC3939 Manuale utente

Cisco

Cisco DPC3929CM Manuale utente

Cisco

Cisco S195 Manuale utente

Cisco

Cisco DPC2434 Manuale utente

Cisco

Cisco SIEMENS HICOM 330E Istruzioni per l'installazione e il funzionamento

Cisco

Cisco DPA 7610 Manuale di istruzioni

Cisco

Cisco VG350 Manuale utente

Cisco

Cisco ASR 5000 Manuale di istruzioni

Cisco

Cisco EVM-IPVS-16A Guida rapida

Cisco

Cisco ASR 9000 Series Manuale di installazione

Cisco

Cisco SPA232D Manuale di istruzioni

Cisco

Cisco VG410 Manuale

Cisco

Cisco Meraki Z3 Manuale utente

Cisco

Cisco 3521 Manuale di servizio

Cisco

Cisco DPC2425 Manuale utente

Manuali Portale popolari di altre marche

LST

LST M500RFE-AS Manuale utente

Kinnex

Kinnex Media Gateway Manuale utente

2N Telekomunikace

2N Telekomunikace 2N StarGate Manuale utente

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuale utente

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Manuale utente

Telsey

Telsey CPVA 500 - SIP Manuale utente

RTA

RTA 460A-NNA4 Scheda tecnica

Shaw

Shaw Gateway HDPVR Manuale utente

ABB

ABB VSN900 Guida rapida

Commander

Commander Pulse Manuale utente

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Manuale utente

NETGEAR

NETGEAR C6300BD Manuale utente

Amit

Amit CDW531AM Manuale utente

HMS

HMS Netbiter EasyConnect EC150 Manuale utente

Huawei

Huawei EchoLife HG620 Manuale utente

AT&T

AT&T U-verse 3801 Manuale per l'uso e la cura

Logic IO

Logic IO RTCU MX2 turbo Manuale utente

Suttle

Suttle MediaMAX MXM-521 Manuale utente