Cisco 8851 Manuale utente

Home

PBXware

SERVERware

TELCOware

SIPmon

SIPProt

Desktop & Mobile

BRM

UADs

Appliances

EOL

From Bicom Systems Wiki

Contents

1 Introduction

■

2 Video Tutorial

■

3 Requirements

■

3.1 Identifying Phone Model

■

3.2 Phone Firmware

■

3.3 DHCP Server

■

3.4 PBXware Version

■

4 Installation

■

4.1 Power Adapter

■

4.2 Find the Phone's IP Address

■

4.3 Reset to Factory Settings

■

5 Registering Device

■

5.1 Manual Configuration

■

5.2 Auto Provisioning

■

6 Configure BLF

■

6.1 Extension Settings

■

Introduction

This Congifuration Guide is written as a general guide on how to configure the Cisco phone

model 8851 to work with PBXware 5.3.8.

Video Tutorial

Please refer to the video tutorial explaining the auto-provisioning setup for a Cisco phone on

PBXware 5.

Requirements

Identifying Phone Model

To start and successfully complete the registration of your Cisco phone, you need to know which

phone model to set up.

On the back of each Cisco phone, there is model information that you should check. Although

various phone models can have exactly the same requirements and installation procedures,

phone models can also have significantly different requirements and installation procedures, so

that is why it is important to know the model you own which results in you setting up the device

successfully.

Phone Firmware

Make sure that your phone is loaded with an appropriate firmware version, 11-3-3.

■

To find out the software version for Cisco 8851, press the menu button, then type 71

■

DHCP Server

Fully configured and operational DHCP server.

■

PBXware Version

PBXware version 5.3.8

In order to find out the PBXware version:

■

Navigate to Settings: About.

■

On the top of About page is a code similar to this one Edition: Multi-Tenant, Release:

5.3.8.0 (2223ce45), Running: 13.23.1-gc-040bbaca, Proxy v5.3.8 (231c5f3), API: 5.3,

libmemcached version: 1.0.18, where Release denotes the current version of your PBXware.

Installation

This section describes how to install and connect the phone to the electrical power and data

network as well as how to apply factory settings.

The following topics are covered:

Power Adapter

■

Factory Settings

■

Power Adapter

Connect the Network and Power

Connect the DC plug on the power adapter to the DC port on the phone and connect the other

■

end of the power adapter into an electrical power outlet.

Connect the Ethernet cable between the Internet port on the phone and the network port on a

■

router or switch to access LAN.

Find the Phone's IP Address

Find out your Cisco phone's IP Address

Press the Settings button

■

Type 72 to check the phone's IP address

■

IP address should be displayed on the phone.

Reset to Factory Settings

This step is not required for brand new out-of-the-box phones, however, if the phone has been

already used, then it is a must.

Press the Settings button

■

Type 65

■

Confirm with OK to factory reset the phone

■

Wait some time for the phone to reboot.

■

NOTE: Do not unplug or remove power to the device while it is updating firmware and

configuration.

Registering Device

This section describes how to identify the Cisco phone model, requirements that must be met

and how to register the phone using manual configuration or auto provisioning.

The following topics are covered:

Manual Configuration

■

Auto Provisioning

■

Manual Configuration

This section describes how to set UAD settings, create a PBXware Extension and register the

phone.

The following topics are covered:

UAD Settings

■

Creating an Extension

■

Registering a Phone

■

UAD Settings

UAD settings

Open a new browser window and enter the IP address in order to access the PBXware's web

■

administration login screen. Example: http://192.168.1.10

■

UAD settings

Navigate to Settings: UAD.

■

Make sure that Cisco UAD is enabled. To check the UAD status, click the Edit icon

■

corresponding to the Cisco phone.

Make sure Status is set to Active, Auto provisioning is set to No, and DHCP is set to Yes.

■

Click the Save button to save changes.

■

Creating an Extension

Creating Extension

Add an Extension

Navigate to Extensions. Click Add Extension.

■

The standard options window will be shown below.

■

Select the Cisco phone model from the UAD select box.

■

Select Location: Local or Remote.

■

Local is for all Extensions registered on the LAN and Remote is for all Extensions

registered from remote networks, WAN, Internet, etc.

Click the Next step button.

■

Extension Values

Enter values into the required field text boxes.

REQUIRED FIELDS:

Name

■

Enter a name for the Extension being created. Example: John Smith.

E-mail

■

Enter the e-mail address associated with this Extension. This e-mail address will receive

all system notification messages. Example: [email protected]

Click the Save button.

■

Optionally, click the Save & E-mail button. The account details will be sent to the e-mail

■

address associated with this Extension.

OPTIONAL FIELDS

Extension

■

An auto-generated Extension number based on the next available sequential number. An

Extension value can be changed. Example: '1003'.

Secret

■

A secret value associated with the UAD is auto-generated in order to allow the UAD to

successfully register with the system. The secret value can be changed, however it is

highly recommended not to change the system generated value to a simple value like

"1234" or "1003" or others.

■

An auto-generated PIN will allow access to voicemail and online self-care (OSC).

Registering a Phone

This section describes how to register a Cisco phone using Hostname or IP Address.

Hostname or IP Address

Open a new browser window and enter the phone's IP address in order to access the phone's

■

web administration interface login screen. Example: http://192.168.1.22.

Click Admin Login in the top right corner of the administration interface.

■

Click Advanced in the top right corner of the administration interface.

■

Click Voice found in the main menu.

■

Click Ext 1 found in the sub menu.

■

Enter or set the following details into the respective fields.

■

REQUIRED FIELDS:

Proxy (Proxy and Registration section)

■

Enter the Hostname or IP Address of PBXware.

- Example of a Hostname: voip.bicomsystems.com

- Example of an IP Address: 192.168.1.10

User ID (Subscriber Information section)

■

PBXware Extension number. Example: 1003.

Password

■

The Secret of the extension as received in the e-mail associated with this Extension.

Example: _%Z4M3*Ts9y7. A password is generated automatically for each newly created

Extension.

Navigate down to the "Dial Plan" section. Clear the Dial Plan field, then copy and paste the

■

following value.

(*x.|**x.|*xx|[3469]11|0|00|[2-9]xxxxxx|1xxx[2-9]xxxxxx|xxxxxxxxxxxx.)

Click the Submit button.

■

You will have to wait some time for the phone to reboot. If everything is done as described

■

above, you should have successfully registered your phone to PBXware.

Auto Provisioning

This section describes how to set UAD settings, create a PBXware Extension and register the

phone using DHCP or Static IP address.

The following topics are covered:

UAD Settings

■

Creating an Extension

■

Registering a Phone

■

UAD Settings

UAD settings

Open a new browser window and enter the IP address in order to access the PBXware's web

■

administration login screen. Example: http://192.168.1.10.

■

UAD settings

Navigate to Settings: UAD.

■

Make sure Cisco UAD is enabled. To check the UAD status, click the Edit icon corresponding

■

to the Cisco phone.

Make sure Status is set to Active, Auto provisioning is set to Yes, and DHCP is set to Yes.

■

Click the Save button to save changes.

■

Creating an Extension

Creating Extension

Add an Extension

Navigate to Extensions. Click Add Extension.

■

The standard options window will be shown below.

■

Select a Cisco phone model from the UAD select box.

■

Select Location: Local or Remote.

■

Local is for all Extensions registered on the LAN and Remote is for all Extensions

registered from remote networks, WAN, Internet, etc.

Click the Next step button.

■

Extension Values

Enter values into the required field text boxes.

REQUIRED FIELDS:

Name

■

Enter a name for the Extension being created. Example: John Smith.

E-mail

■

Enter the e-mail address associated with this Extension. This e-mail address will receive

all system notification messages. Example: [email protected]

Auto Provisioning

■

Set to Yes.

MAC Address

■

Enter the Cisco phone's MAC address. Example: 0002FDFF1536. The MAC address can

be found at the back of the phone.

Click the Save button.

■

Registering a Phone

This section describes how to register a Cisco phone using DHCP, TFTP, or HTTP & HTTPS.

The following topics are covered:

DHCP

■

TFTP or HTTP & HTTPS

■

DHCP

Configure DHCP

Make sure that your DHCP router is configured to use option 66 to automatically instruct

■

devices with the URL for auto provisioning. For more information, please refer to your router

documentation or contact your network administrator.

Phone's first boot or user-initiated reboot

The auto-provisioning process will start during the phone's first boot or after the reboot

■

process has been initiated by the user. The DHCP server will instruct the phone from where to

pick up an appropriate configuration file. If everything is done as described above, you should

have successfully registered your phone to PBXware.

TFTP or HTTP & HTTPS

Open a new browser window and enter your phone's IP address in order to access the phone's

■

web administration interface login screen. Example: http://192.168.1.22

Click Admin Login in the top right corner of the administration interface.

■

Click Advanced in the top right corner of the administration interface.

■

Click Voice at the top navigation menu.

■

Click Provisioning found in the sub-menu.

■

You can use TFTP or HTTP & HTTPS protocols in order to auto-provision your Cisco phone.

■

TFTP

This section describes how to use TFTP protocol in order to register the Cisco phone.

In the Profile Rule field, enter tftp:// followed by a Hostname or an IP Address, then

■

followed by /$MA.cfg.

- Example of a Hostname: tftp://voip.bicomsystems.com/$MA.cfg

- Example of an IP Address: tftp://10.1.70.150/$MA.cfg

Click Submit and wait for 35 seconds. The phone may reboot.

■

The auto-provisioning process will start during the phone's reboot process. The phone will pick

■

up an appropriate configuration file from PBXware. If everything is done as described above,

you should have successfully registered your phone to PBXware.

HTTP & HTTPS

This section describes how to use HTTP & HTTPS protocol in order to register the Cisco phone.

NOTE: Your PBXware needs to be configured correctly for HTTP to work. Please make sure

that HTTP username and HTTP passwords are set in the auto-provisioning section in 'Settings' -

> 'Servers/Tenants' -> 'Server/Tenant Name'.

Please contact your PBXware administrator. Bicom Systems can provide a service to set this up

for you.

In the Profile Rule field, enter the following:

■

- Example of a Hostname using HTTP: [--uid username --pwd

password]http://voip.bicomsystems.com/prov/$MA.cfg

- Example of a Hostname using HTTPS: [--uid username --pwd

password]https://voip.bicomsystems.com/prov/$MA.cfg

- Example of an IP Address using HTTP: [--uid username --pwd

password]http://10.1.70.150/prov/$MA.cfg

- Example of an IP Address using HTTPS: [--uid username --pwd

password]https://10.1.70.150/prov/$MA.cfg

Altri manuali per 8851

Indice

Altri manuali Cisco Telefono IP

Cisco

Cisco SPA 303 Series Manuale utente

Cisco

Cisco Unified 7900 Series Manuale utente

Cisco

Cisco 7910 - IP Phone VoIP Manuale utente

Cisco

Cisco 8811 Guida alla risoluzione dei problemi

Cisco

Cisco SPA504 Manuale utente

Cisco

Cisco 8821 Manuale utente

Cisco

Cisco MCS 7800 Series Manuale utente

Cisco

Cisco 9951 Standard Manuale utente

Cisco

Cisco 6800 Series Manuale utente

Cisco

Cisco 7945 Series Manuale utente

Cisco

Cisco 7921G - Unified Wireless IP Phone VoIP Manuale utente

Cisco

Cisco 6861 Guida di riferimento rapido

Cisco

Cisco 7970 Series Manuale utente

Cisco

Cisco 8811 Manuale utente

Cisco

Cisco 8800 Series Manuale utente

Cisco

Cisco 7975G - Unified IP Phone VoIP Guida rapida

Cisco

Cisco Razorline 7975 Manuale utente

Cisco

Cisco Unified 7900 Series Come usare

Cisco

Cisco Cisco 7940 Manuale utente

Cisco

Cisco 7906G - Unified IP Phone VoIP Manuale utente

Cisco

Cisco SPA50 Series Manuale utente

Cisco

Cisco 8941 Manuale utente

Cisco

Cisco Cisco Unified IP Phone 7960G Manuale di servizio

Cisco

Cisco SPA-500 Series Manuale utente

Manuali Telefono IP popolari di altre marche

Alcatel

Alcatel 4028 Manuale utente

Polycom

Polycom Polycom VVX 600 Manuale utente

Polycom

Polycom SoundPoint IP 450 Manuale utente

Polycom

Polycom SoundPoint IP 650 Manuale utente

Proximus

Proximus Maestro 3016 IP Manuale utente

Fanvil

Fanvil X4 Manuale utente

Snom

Snom 320 Manuale utente

Yealink

Yealink Yealink SIP-T46G Manuale utente

Avaya

Avaya 4625SW Manuale utente

Yealink

Yealink SIP-T52S Manuale utente

Nortel

Nortel 1140E Manuale utente

Nexotek

Nexotek NT-P500 Manuale utente

Avaya

Avaya Integral 5 R3.0 Manuale utente

GE 28320EE2 - Dect 6.0 InfoLink 2 Manuale utente

Avaya

Avaya 4600 Series Manuale di servizio

Mitel

Mitel MIVOICE OFFICE 400 6940 SIP Manuale utente

Nortel

Nortel i2050 Manuale utente

Fiberme

Fiberme FAP260 Series Manuale utente