Cisco NCS 1004 Manuale utente
Install Cisco NCS 1004
This chapter contains procedures to install Cisco NCS 1004.
•Rack Compatibility, on page 1
•Install NCS 1004 on an EIA/ANSI/ ETSI Rack, on page 3
•Stacking NCS 1004, on page 16
•General Power and Grounding Requirements, on page 17
•Power Supply, on page 19
Rack Compatibility
This section provides rack compatibility details for the Cisco NCS 1004.
Figure 1: Four Post Rack Type
Install Cisco NCS 1004
1
Figure 2: Four Post Rack Type
Figure 3: Two Post Rack Type
Install Cisco NCS 1004
2
Install Cisco NCS 1004
Rack Compatibility
Figure 4: Rack Specification
Mounting Flange
Dimension Z
Rack Mounting Hole
Center-Center Y
Rack Front Opening XRack Type
482.6mm (19")465mm (18.312")450.8mm (17.75")19" racks
584.2mm (23")566.7mm (22.312")552.45mm (21.75")23" racks
533.4mm(21")515.0mm(20.276")500.0mm(19.68")ETSI racks
The distance between the front and the rear post in a four post rack is 427 mm (closed position) and 707 mm
(open position).
Note
Install NCS 1004 on an EIA/ANSI/ ETSI Rack
It is mandatory to fix the fiber management brackets for all the cards in the chassis before installing the Cisco
NCS 1004 chassis onto the rack. See Attach Fiber Management Bracket section for the detailed procedure.
Install Cisco NCS 1004
3
Install Cisco NCS 1004
Install NCS 1004 on an EIA/ANSI/ ETSI Rack
Figure 5: Line Cards fitted with Fiber Management Bracket
Figure 6: Filler Cards fitted with Fiber Management Bracket
In ETSI racks, to maintain a footprint of 600 mm, the cabinet door cannot be installed and the horizontal bar
of the fiber management bracket should be maintained at the shortest length. See Adjusting the Fiber
Management Bracket.
Note
Install Cisco NCS 1004
4
Install Cisco NCS 1004
Install NCS 1004 on an EIA/ANSI/ ETSI Rack
The sliding rail must be used only for first chassis positioning. The chassis must be fixed with screws on the
front side.
Caution
Use only the fastening hardware provided with Cisco NCS 1004 to prevent loosening, deterioration, and
electromechanical corrosion of the hardware and joined material.
Caution
Before you begin
Ensure the rack is compatible. See the Rack Compatibility section.
Step 1 Attach the left and right mounting brackets to the chassis using the screws (48-2029-01) and tighten them to a torque
value of 1.5 N-m.
The left and right brackets have been marked accordingly.
Figure 7: Fixing the Brackets
Right Bracket (700-116388-01)1
Screws used for brackets2
Left Bracket (700-116386-01)3
Step 2 Install the four post slider or two post slider on the rack.
a) Install Two Post Slider into an EIA/ANSI Rack
b) Install Four Post Slider into an EIA/ ANSI Rack
Install Cisco NCS 1004
5
Install Cisco NCS 1004
Install NCS 1004 on an EIA/ANSI/ ETSI Rack
c) Install Two Post Slider into an ETSI Rack
d) Install Four Post Slider into an ETSI rack
Step 3 Insert the chassis (with brackets) onto the sliders assembled on the rack.
Step 4 After the chassis is completely inserted, fasten the chassis with four screws (48-101524-01) on each side of the bracket,
and using a number-2 Phillps screwdriver, tighten them to a torque value of 4.65 N-m.
See Install Air Filter for the air filter installation procedure, before you fasten the chassis to the rack.
Install Two Post Slider into an EIA/ANSI Rack
This procedure has details about installing the two post slider into an EIA/ ANSI rack.
Step 1 Identify the two post slider and adjust the length of the slider (3" to 5").
Slide the inner sliders and adjust the length to mate with the rack surface.
Figure 8: Two Post Slider Identification
Check for marking on the sliders; the right and the left sliders are indicated.1
Step 2 Integrate the two post slider with the rack. The procedure for 23" and 19" rack is discussed here:
• 19" rack - the slider can be directly fitted on to a 19" rack. On the front side, insert only the top most screw of the
slider (48-101524-01) and tighten it to a torque value of 4.65 N-m. On the rear side, insert three screws (48-101524-01)
and tighten to a torque value of 4.65 N-m.
• 23" rack - the slider is fitted on to a 23" rack using an adapter (refer the following image). The formed surface must
always face the inner side of the rack post. On the front side of the adapter (towards the chassis), insert only the top
most screw of the slider (48-101524-01) and tighten it to a torque value of 4.65 N-m. On the rear side (towards the
chassis), insert three screws (48-101524-01) and tighten them to a torque value of 4.65 N-m. For the adapter portion
which is towards the rack, all the six screws are fitted on the front and rear side.
Install Cisco NCS 1004
6
Install Cisco NCS 1004
Install Two Post Slider into an EIA/ANSI Rack
Figure 9: Two Post Slider Integration - 19" Rack
Inner surface of the sliding bracket.1
Slider fixing screws (48-101524-01)2
Install Cisco NCS 1004
7
Install Cisco NCS 1004
Install Two Post Slider into an EIA/ANSI Rack
Figure 10: Two Post Slider Integration - 23" Rack
Adapter1
Slider fixing screws (48-101524-01)2
Install Four Post Slider into an EIA/ ANSI Rack
This procedure has details about installing the four post slider into an EIA/ ANSI rack.
Step 1 Identify the four post slider and adjust the length of the slider.
Slide the inner slider arm and adjust the length to mate with the rack surface.
Install Cisco NCS 1004
8
Install Cisco NCS 1004
Install Four Post Slider into an EIA/ ANSI Rack
Figure 11: Four Post Slider Identification
Slide and adjust the length of the slider arm.1
Step 2 Integrate the four post slider with the rack. The procedure for the 23" and 19" rack is discussed here:
• 19" rack - the slider can be directly fitted on to a 19" rack. On the front side, insert only the top most screw of the
slider (48-101524-01) and tighten it to a torque value of 4.65 N-m. On the rear side, insert five screws (48-101524-01)
and tighten them to a torque value of 4.65 N-m.
• 23" rack - the slider is fitted on to a 23" rack using an adapter (refer the following image). The formed surface must
always face the inner side of the rack post. On the front side (towards the chassis), insert only the top most screw
of the slider (48-101524-01) and tighten it to a torque value of 4.65 N-m. On the rear side (towards the chassis),
insert five screws (48-101524-01) and tighten them to a torque value of 4.65 N-m. For the adapter portion which is
towards the rack, all the six screws are fitted on the front and rear side.
Install Cisco NCS 1004
9
Install Cisco NCS 1004
Install Four Post Slider into an EIA/ ANSI Rack
Figure 12: Four Post Slider Integration - 19" Rack
Edge surface of the slider1
Slider fixing screws (48-101524-01)2
Install Cisco NCS 1004
10
Install Cisco NCS 1004
Install Four Post Slider into an EIA/ ANSI Rack
Altri manuali per NCS 1004
5
Indice
Altri manuali Cisco Hardware di rete
Cisco
Cisco Linksys Business Series Network Storage System... Manuale utente
Cisco
Cisco CE 2000 Platform SCE 2000 4xGBE Manuale dell'operatore
Cisco
Cisco ASR 9000 Series Manuale utente
Cisco
Cisco Firepower 1010 Manuale utente
Cisco
Cisco VIC-2FXS - 3600 Voice Interface Card-Fxs... Manuale di istruzioni
Cisco
Cisco MERAKI CW9166D1 Manuale utente
Cisco
Cisco Wide Area Virtualization Engine 274 Manuale
Cisco
Cisco ATM Cable Interface Processor ACIP-SM(=) Manuale dell'operatore
Cisco
Cisco ISA500 Series Manuale di istruzioni
Cisco
Cisco IAD1101 Manuale utente
Cisco
Cisco Firepower 2100 Series Manuale utente
Cisco
Cisco NCS 1000 Manuale utente
Cisco
Cisco MERAKI MR57 Manuale utente
Cisco
Cisco Aironet 1000 Series Manuale
Cisco
Cisco NSS2000 Series Manuale utente
Cisco
Cisco Firepower 1010 Series Manuale
Cisco
Cisco 6500 - Catalyst Series 10 Gigabit EN Interface Module... Manuale utente
Cisco
Cisco GS7000 Istruzioni operative
Cisco
Cisco 15530-LCMB-0200 - ESCON Multiplexing Line Card... Manuale
Cisco
Cisco Firepower 9300 Manuale
Manuali Hardware di rete popolari di altre marche
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manuale utente
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manuale utente
Yudor
Yudor YDS-16 Manuale utente
D-Link
D-Link ShareCenter DNS-320L Manuale utente
Samsung
Samsung ES1642dc Istruzioni per l’uso
Honeywell Home
Honeywell Home LTEM-PV Istruzioni per il montaggio
