Cisco NCS 1010 Foglio di istruzioni
Install Cisco NCS 1010
This chapter contains tasks to install Cisco NCS 1010.
•Rack Compatibility, on page 1
•Install Slide Rail into the Rack, on page 2
•General Power and Grounding Requirements, on page 6
•Equipment Installation to Power Warnings, on page 10
•Rack-Mount Warnings, on page 12
•Install Cisco NCS 1010 on an EIA/ANSI/ETSI Rack, on page 12
Rack Compatibility
The NCS1010 chassis can be installed in a standard EIA (19"), ANSI (23"), or ETSI rack. .
• The rack can be two post type or four post type rack.
• The 19" and 23" racks must be compliant with "EIA Universal" holes.
• The ETSI Rack must be compliant with "ETSI Universal" holes.
Figure 1: Rack Specification
Install Cisco NCS 1010
1
Mounting Flange
Dimension Z
Rack Mounting Hole
Center-Center Y
Rack Front Opening XRack Type
482.6mm (19")465mm (18.312")450.8mm (17.75")19" racks
584.2mm (23")566.7mm (22.312")552.45mm (21.75")23" racks
533.4mm(21")515.0mm(20.276")500.0mm(19.68")ETSI racks
Install Slide Rail into the Rack
The length of the slide rail fits only in the front posts of the four-post rack. Therefore, the same slide rails can
be used for both two-post and four-post racks.
•Install Slide Rail into an EIA 19" Rack, on page 2
•Install Slide Rail into an ANSI 23" Rack, on page 3
•Install Slide Rail into an ETSI Rack, on page 4
Install Slide Rail into an EIA 19" Rack
Use the following task to install the slide rail into two-post or four-post EIA rack.
Procedure
Step 1 Identify the left side and right side slide rail.
Step 2 On the left side front post of the rack, place the left side slide rail.
Step 3 Insert all the four screws into the slide rail, one by one.
Figure 2: Slide Rail Integration - EIA Rack
Slide rail1
Install Cisco NCS 1010
2
Install Cisco NCS 1010
Install Slide Rail into the Rack
8x 12–24 Pan head screws2
Step 4 Tighten the screws to a torque value of 4.65 N-m (41 lbs-in).
Step 5 Similarly, fix the right side slide rail on the right side front post.
Install Slide Rail into an ANSI 23" Rack
Use the following task to install the slide rail into a two-post or four-post ANSI rack.
Procedure
Step 1 Identify the left side and right side slide rails.
The slide rail is fitted on to an ANSI rack using a 23" rack to 19" rack adapter.
Step 2 Identify the left side and right side adapters.
Step 3 Fix the adapters on both the left side and right side posts using the 12–24 screws that are available in the
accessory kit (NCS1010-23-KIT).
Figure 3: Fixing 23" Adapter
23" rack to 19" rack adapter1
12–24 screws (14x)2
Step 4 On the left side adapter, place the left side slide rail and insert the 12–24 pan head screws.
Install Cisco NCS 1010
3
Install Cisco NCS 1010
Install Slide Rail into an ANSI 23" Rack
Figure 4: Slide Rail Integration
Slide rail1
12–24 Pan head screws (8x)2
Step 5 Tighten the screws to a torque value of 4.65 N-m (41 lbs-in).
Step 6 Similarly, fix the right side slide rail on the right side post.
Install Slide Rail into an ETSI Rack
Use the following task to install the slide rail into a two-post or four-post ETSI rack.
Procedure
Step 1 Identify the left side and right side slide rail.
The slide rail is fitted on to an ETSI rack using an ETSI to 19" adapter. The same adapter can be used for both
left and right sides.
Step 2 Fix the adapters on both the left side and right side posts using the M6 four screws available in the accessory
kit (NCS1010-ETSI-KIT).
Install Cisco NCS 1010
4
Install Cisco NCS 1010
Install Slide Rail into an ETSI Rack
Figure 5: Fixing 19'' to ETSI Adapter
ETSI rack to 19" rack adapter1
M6 screws (8x)2
Step 3 On the left side adapter, place the left side slide rail and insert the12–24 pan head screws (4x).
Figure 6: Slide Rail Integration - ETSI Rack
Step 4 Tighten the screws to a torque value of 4.65 N-m (41 lbs-in).
Step 5 Similarly, fasten the right side slide rail on the right side adapter.
Install Cisco NCS 1010
5
Install Cisco NCS 1010
Install Slide Rail into an ETSI Rack
General Power and Grounding Requirements
General power and grounding requirements are:
• Installation of the routing system must follow national and local electrical codes:
• In the United States: United States National Fire Protection Association (NFPA) 70 and United
States National Electrical Code (NEC).
• In Canada: Canadian Electrical Code, part I, CSA C22.1.
• In other countries: International Electrotechnical Commission (IEC) 60364, parts 1 through 7.
• Two separate and independent AC or DC power sources are needed to provide 2N redundancy for system
power. Each power source requires its own circuit breaker.
• Each power source must provide clean power to the site. If necessary, install a power conditioner.
• The site must provide short-circuit (over-current) protection for devices.
• Proper grounding is required at the site to ensure that equipment is not damaged by lightning and power
surges.
Ground lug connection is mandatory for the AC chassis version too.
Note
• Site power planning must include the power requirements for any external terminals and test equipment
you will use with your system.
Be sure to review the safety warnings in the Regulatory Compliance and Safety Information - Cisco Network
Convergence System 1010 before attempting to install the chassis.
Note
Ground Connection Warnings
Take note of the following ground connection warnings:
The appliance must be connected to a grounded outlet.
Apparatets stikprop skal tilsluttes en stikkontakt med jord, som giver forbindelse til stikproppens jord.
Laite on liitettävä suojakoskettimilla varustettuun pistorasiaan.
Apparatet må tilkoples jordet stikkontakt.
Apparaten skall anslutas till jordat uttag. Statement 414
Warning
Install Cisco NCS 1010
6
Install Cisco NCS 1010
General Power and Grounding Requirements
To reduce risk of electric shock and fire, you must incorporate a readily accessible two-poled disconnect
device in the fixed wiring. Statement 1022
Warning
To reduce risk of fire, use copper conductors only. Statement 1025
Warning
To reduce the risk of electric shock, refer to national and local codes for proper installation and
grounding of antennas. Statement 1052
Warning
Ground Cisco NCS 1010
In the installation of the chassis, the ground lug must be connected first.
This task provides the grounding details for the Cisco NCS 1010 chassis. In the installation of the chassis,
connect the ground lug first.
High touch/leakage current—Permanently connected protective earth ground is essential before
connecting to the system power supply. Statement 342
Warning
When terminating the frame ground, do not use soldering lug blocks, screwless (push-in) blocks, quick connect
blocks, or other friction-fit blocks.
Caution
The ground lug must be attached before energizing the chassis.
Note
Procedure
Step 1 Connect the ground lug in one of the following ways as per your requirement:
a. To connect the ground lug in the front side:
• Fix the upper two screws of the left slide rail.
• Align the ground adapter (provided with ETSI accessory kit (NCS1010-ETSI-KIT)), with the lower
two screw holes of the slide rail.
• Fix the lower screws using a screw driver to a torque value of 4.65 N-m (41 lbs-in). These screws
hold both the ground adapter and the slide rail.
• Place the ground lug on the ground adapter and insert the two screws with the washers.
Install Cisco NCS 1010
7
Install Cisco NCS 1010
Ground Cisco NCS 1010
• Tighten the screws by using a screw driver to a torque value of 3.1 N-m (27.4 lbs-in).
Figure 7: Fixing Ground Lug on the Ground Adapter - ETSI Rack
Ground adapter1
12–24 Pan head screws2
Ground lug3
Washers (2x)4
M5X10mmL Screws (2x)5
You can use the preceding option 'a' only for the ETSI rack.
Note
b. To connect the ground lug in the front side:
• Place the lug on the provision at the rear side of the left slide rail.
• Fix the M5X10mmL screws with the washers, by using a screw driver to a torque value of 3.1 N-m
(27.4 lbs-in).
Install Cisco NCS 1010
8
Install Cisco NCS 1010
Ground Cisco NCS 1010
Figure 8: Fixing Ground Lug in the Rear Side of the Slide Rail
Ground lug1
Washers (2x)2
M5X10mmL screws (2x)3
c. To fix the ground lug at the rear side of the chassis:
• Place the lug on that provision at the rear left side of the chassis. You can see a grounding symbol
next to the provision for the ground lug.
• Fix the M5X10mmL screws with the washers by using a screw driver to a torque value of 3.1 N-m
(27.4 lbs-in).
Install Cisco NCS 1010
9
Install Cisco NCS 1010
Ground Cisco NCS 1010
Figure 9: Fixing Ground Lug in the Rear Side of the Chassis
Ground lug1
Washers (2x)2
M5X10mmL Screws (2x)3
When you use the options 'a' and 'b', the ground lug remains attached to the slide rails. This allows
you to remove the chassis without needing to remove the ground lug.
Note
If the ETSI rack does not have rear access, front ground lug (option 'a') must be attached before
mounting the NCS1010 chassis on the slide rails. In all other cases, you can use the two rear ground
lug options (option s 'b' and 'c") that can be assembled after the chassis is mounted on slide rails.
Note
Step 2 Verify that the office ground cable is connected to the top of the rack and the office ground, according to local
site practice.
Step 3 Remove any paint and other nonconductive coatings from the surfaces between the shelf ground and bay
frame ground point. Clean the mating surfaces and apply appropriate antioxidant compound to the bare
conductors.
Step 4 Attach one end of the shelf ground cable (#6 AWG cable) to the ground point using the lug.
Step 5 Attach the other end of the shelf ground cable to the bay frame using a lug connector according to the equipment
rack frame specifications.
Equipment Installation to Power Warnings
Take note of the following power safety warnings:
To reduce the risk of electric shock, secure the modules with the provided screws. Statement 347.
Warning
Install Cisco NCS 1010
10
Install Cisco NCS 1010
Equipment Installation to Power Warnings
Altri manuali per NCS 1010
2
Indice
Altri manuali Cisco Hardware di rete
Cisco
Cisco Octal-Port DMT ATU-C Line Card Manuale tecnico
Cisco
Cisco MA-UMNT-MR-A3 Manuale utente
Cisco
Cisco ASR 5000 Series Manuale utente
Cisco
Cisco ONS 15454 SDH Manuale
Cisco
Cisco SCE 1000 and Manuale dell'operatore
Cisco
Cisco N540X-6Z18G-SYS-A Manuale utente
Cisco
Cisco Cisco ONS 15600 SDH Manuale utente
Cisco
Cisco IDS-4230-FE - Intrusion Detection Sys Fast Ethernet... Manuale dell'operatore
Cisco
Cisco ONS 15454 Manuale di istruzioni
Cisco
Cisco ISA500 Series Manuale utente
Cisco
Cisco 2431 - IAD Router Manuale utente
Cisco
Cisco TELEPRESENCE MCU ACCESSING CONFERENCES - Manuale utente
Cisco
Cisco Catalyst X6148 Manuale utente
Cisco
Cisco NCS 1002 Aggiornamento firmware
Cisco
Cisco C7200-I - Input/Output Controller - Control... Manuale utente
Cisco
Cisco 5400 Series Manuale di istruzioni
Cisco
Cisco NCS 2000 series Manuale utente
Cisco
Cisco NSS2000 Series Manuale utente
Cisco
Cisco C8510MSR-SKIT-DC - Catalyst 8510 Multiservice Switch... Manuale utente
Cisco
Cisco ISA500 Series Manuale di istruzioni
Manuali Hardware di rete popolari di altre marche
Matrix Switch Corporation
Matrix Switch Corporation MSC-HD161DEL Manuale utente
B&B Electronics
B&B Electronics ZXT9-IO-222R2 Manuale utente
Yudor
Yudor YDS-16 Manuale utente
D-Link
D-Link ShareCenter DNS-320L Manuale utente
Samsung
Samsung ES1642dc Istruzioni per l’uso
Honeywell Home
Honeywell Home LTEM-PV Istruzioni per il montaggio
